Glacier bay FW6AC012CP Assembly instructions

INSTALLATION AND CARE GUIDE
Questions, problems, missing parts?
Before returning to the store, call Glacier Bay Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday
9 a.m. - 6 p.m., EST, Saturday
1-855-HD-GLACIER (1-855-434-5224)
HOMEDEPOT.COM/GLACIERBAY
THANK YOU
We appreciate the trust and confidence you have placed in Glacier Bay through the purchase of this lavatory
faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see
our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!
WIDESPREAD LAVATORY FAUCET
Model#
FW6AC012CP
FW6AC012BNV
FW6AC012BL
SKU#
304774945
304774954
304774956
THD 09/2017 REV.02

2
□Observe all local plumbing and building codes.
□Cover the drain in your sink to avoid losing parts.
□Review the care and cleaning section included in this guide.
□This product is engineered to meet the EPA WaterSense flow requirement. The flow rate is governed by the
aerator or flow controller. If replacement is ever required, be sure to replace it with a WaterSense compliant
aerator or flow controller to retain the water conserving flow rate of this product.
Important Information..............................2
Warranty ...................................................2
Pre-installation.........................................2
Planning Installation ................................2
Tools and Hardware Required..................2
Package Contents....................................3
Installation................................................4
Operation...................................................8
Care and Cleaning ....................................9
Troubleshooting........................................9
Service Parts...........................................10
Table of Contents
Important Information
Warranty
Pre-installation
Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our
limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of
defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.
Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD Glacier (1-855-434-
5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer
purchaser must be made available for all Glacier Bay warranty claims.
This warranty excludes incidental / inconsequential damages and failures due to misuse, abuse or normal wear and
tear. This warranty excludes all industrial, commercial & business usage, whose purchasers are hereby, extended
a five year limited warranty from the date of purchase, with all other terms of this warranty applying except the
duration of warranty.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specific legal rights and you may also have other
rights that vary from state to state and province to province. Please see a store or contact 1-855-HD Glacier for
more details.
Before you begin to install this product, ensure that all parts are present. Compare parts with the package
contents list. If any part is missing or damaged, do not attempt to install the product. Contact customer service for
replacement parts.
LIMITED LIFETIME WARRANTY
PLANNING INSTALLATION
TOOLS AND HARDWARE REQUIRED
SILICONE
Adjustable
Wrench
Phillips
Screwdriver
Channel-
Lock Pliers
Safety
Goggles Sealant
(2)
Supply
Lines

3HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER for further assistance.
Pre-Installation (continued)
PACKAGE CONTENTS
C*
D*
E*
B
A
G*
H*
I*
J
K
F*
Faucet Assembl
yD
rain Assembly
U
S
T
Q
R
M*
L*
N*
O*
P*
NOTE: *Items come pre-assembled.
Part Description Quantity
AFaucet body 1
BHandle assembly - Hot 1
CRubber washer 2
DMetal washer 2
EGuide washer 2
FAerator 1
GRubber spacer 1
HMetal spacer 1
ILock nut 1
JQuick connecting hose 1
KHandle assembly - Cold 1
Part Description Quantity
LPop up stopper 1
MDrain flange 1
NRubber washer 1
OLock nut 1
PDrain body 1
QJoint 1
RHorizontal rod 1
SLift rod strap 1
TClip 1
ULift rod 1

4
Installation
G
H
I
A
G
H
I
I
A
E
K
C
D
E
B
E
K
B
CAUTION: Always turn off the water supply before
removing an existing faucet or replacing any part of a
faucet. Open the faucet handle to relieve water pressure
and ensure that the water is completely shut off.
1 Installing the faucet assembly 2 Installing the faucet handles
□Shut off the water supply. Remove the old
faucet.
□Clean the mounting surface.
□Place the faucet (A) through the mounting
holes in the sink.
□Ensure the slot openings of the rubber
spacer (G) and metal spacer (H) face toward
the rear of the sink.
□Secure the faucet (A) to the sink using the
lock nut (I) provided.
□Remove the preassembled guide washers (E),
metal washers (D) and rubber washers (C) from
the hot and cold faucet handles (B and K).
□Loosen the screws on the guide washers (E) until
the ends of the screws are flush with the face of
the guide washers (E).
□Insert the hot faucet handle (B) to the left of the
spout and cold faucet handle (K) to the right of
the spout.
□Attach the faucet handles (B and K) under-neath
the sink using the rubber washers (C), metal
washers (D) and guide washers (E). Securely
tighten the screws on the guide washers (E).

5HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER for further assistance.
Installation (continued)
1
2
SILI
N
1
O
M
P
1
2
N
O
P
M
L
3 Preparing the pop-up assembly 4 Installing the drain body
□Remove the pop up stopper (L) and drain flange
(M) from the drain body (P).
□Screw the lock nut (O) all the way down, and
push the rubber washer (N) down.
□Apply silicone sealant (not included) under the
drain flange (M) and place the drain flange (M)
over the drain hole in the sink.
□From underneath the sink, screw the drain body
(P) onto the drain flange (M). Ensure that the
opening (1) for the ball rod on the drain body (P)
faces towards the rear of the sink.
□Tighten the rubber washer (N) and lock nut (O)
on the drain body (P). Do not overtighten.

6
1
3
Insert 2
Insert 1
2
R
Q
R
Q
2
1
P
L
P
Installation (continued)
5 Installing the stopper and
horizontal rod
□Slide the lift rod (U) through
the faucet (A).
□Slide the lift rod (U) down
into the lift rod strap (S)
until it clicks into the lift rod
strap (S).
2
U
S
U
S
U
1
A
6 Installing the lift rod
□Before installation, unscrew the protective cap (1)
from the horizontal rod (R).
□Insert the stopper (L) into the drain hole in the
sink.
□Insert the horizontal rod (R) into the drain body
(P) and through the hole of the stopper (L). See
insert 1.
□For easier removal and cleaning, rotate the
stopper (L) 90 degrees so that the horizontal rod
(R) does not go through the hole in the stopper
(L). See insert 2.
□Make sure the joint (I) on the horizontal rod (R)
inserts into the drain body (P) completely, as
shown (2). You can press the two sides of the
joint (I) to remove the horizontal rod (R).

7HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER for further assistance.
Installation (continued)
1
3
2
3
4
4
5
S
T
S
T
S
T
L
T
R
L
R
L
R
Hole
7 Attaching the horizontal rod and strap
□Press the rod (R) down to ensure the stopper (L) is in the maximum open position.
□Slide the clip (T) upward, adjust the location of the lift rod strap (S) to the appropriate height and insert the
horizontal rod (R) with the correct hole of the lift rod strap (S).
□Move the lift rod strap (S) in or out to choose an appropriate location.
□Slide the clip (T) downward until it secures with the horizontal rod (R).
NOTE: If the pop up lift rod strap (S) is interfering with your installation, the lift rod strap (S) can be cut shorter. Once you have identified
the proper hole in the lift rod strap (S) that is necessary for your installation, you may cut off the bottom portion of the lift rod strap (S).
NOTE: If a shorter lift rod (U) is required for your installation, you may call Glacier Bay Customer Service for assistance.
8 Checking the operation of the
pop up
□Operate the lift rod (U) up and down to verify
that the stopper (L) opens and closes correctly.
U
L

8
Installation (continued)
A
JK
I
1
2
3
B
FK
A
Flushing and checking for leaks
1
Operation
IMPORTANT: After installation is complete, remove
the aerator to the flush the water lines. Do not lose the
gasket in the aerator.
9 Attaching the quick connecting
hose
□Remove the cap from the quick connect hose.
□Attach the quick connecting hose (I)
connections to the hot faucet handle (A)
connection, faucet body (J) connection, and
cold faucet handle (K) connection. Push until
the connections snap together.
□Pull down moderately to ensure the connection
has been made.
10
Connecting the supply lines
□Use 1/2 in. I.P.S. faucet connections (1), or
a 3/8 in. O.D. ball-nose riser (2) with supply
line coupling nuts (3) (not included).
□Use two wrenches to tighten the
connections. Do not over tighten or torque
the copper supply line.
□Ensuring the handles are in the off position,
turn on the water supply and check for
leaks. If you discover any leaks, check your
connections to ensure they are installed
properly.
□Use a coin to remove the aerator (F) from the
faucet (A). Turn on the hot and cold handles to
allow the water to run for at least one minute.
This flushes away any debris that could cause
damage to internal parts.
□Turn off the water and reinstall the aerator and
housing (if applicable).

9HOMEDEPOT.COM/GLACIERBAY
Please contact 1-855-HD-GLACIER for further assistance.
3
2
1
Care and Cleaning
Troubleshooting
Removing the quick connecting
hose
Operation (continued)
2
CAUTION: Use caution when removing the quick
connecting hose connections in order to prevent cutting
your hands.
NOTE: Refer to the service parts section in this manual for a
detailed drawing showing the location of the parts listed below.
Problem Possible Cause Solution
There are leaks from the
handle.
□The bonnet nut is loose.
□The O-ring on the cartridge is
dirty or damaged.
□Tighten the bonnet nut.
□Clean or replace the O-ring.
The aerator leaks or has a
reduced water ow.
□The aerator is dirty or mis-fitted.
□The cartridge may be clogged.
□Remove the aerator and check for debris.
□Remove cartridge and check for debris.
□Ensure the aerator is properly installed.
The spout leaks.
□The retainer nut is loose. □Tighten the retainer nut.
The sink drain at the base of
the sink is leaking.
□The sink surface is rough or
irregular.
□Apply additional silicone sealant to the
beveled side of the drain ange.
□Retighten and test for leaks.
The water will not shut off
completely.
□The locking nut is loose or
cartridge is not positioned
correctly.
□Remove the cartridge to check the rubber
seat and spring.
□Tighten the lock nut.
□Clean or replace.
□If it is necessary to remove the quick
connector, push the quick connecting hose (I)
up, hold the housing together and pull down.
□To clean, wipe down with a damp cloth and towel dry.
□Do not use abrasive cleaners, steel wool, or harsh chemicals when cleaning this faucet, or the warranty will
be voided.

10
*Specify Finish
Service Parts
2.
1.
6.
8.
5.
3.
18.
10.
12.
11.
13.
14.
15.
16.
17.
9.
7.
4.
DATE CODE：
DO NOT REMOVE
1-888-328-2383
HOT
Part Description Part No.
1Handle A069455*
2Index button & set screw A075210
3Handle extension (C) A66D574C
4Handle extension (H) A66D574H
5Bonnet nut A016003*
6Ceramic disc cartridge (C) A507104N
7Ceramic disc cartridge (H) A507103N
8Handle trim ring A667287*
9Handle valve body A661047W
Part Description Part No.
10 Handle mounting hardware
assembly A663951
11 Spout assembly A666442W*
12 Spout trim ring A667288*
13 Spout mounting
Hardware A66D455
14 Supply hose A135004N
15 Aerator A500026N-T*
16 Lift rod A025110*
17 ClickInstall™ drain assembly A505032*
18 Aerator wrench A031245
Faucet ID Tags can be found
on the hot supply line
Many replacement cartridges, aerators, and drain
assemblies can be purchased at your local The
Home Depot store or online at HOMEDEPOT.COM.