Glasdon NEXUS 8G Specifications

All CMYK Versions
White
NEXUS® 8G
OPERATOR INSTRUCTIONS
IMPORTANT NOTE: ENSURE ALL RELEVANT PERSONNEL READ THESE INSTRUCTIONS PRIOR TO OPERATION.
LIFT OFF WALL FIXING KIT
OPENING YOUR NEXUS 8G
Using finger lip at front of lid,
lift lid upwards.
Lift lid to upright position
until it is held by stay
feature.
SECURING SACK IN POSITION
Stretch sack and hook over side
and front lugs so that sack does
not over hang body of
container. Close lid securing
sack in position.
With lid open, install correct
size sack (approx 13 " x 21" x
23½ " available from Glasdon)
by firstly hooking onto
retention lugs at back
of container.
Using wall fixing bracket as
template, mark out 4 off drill
holes at top and bottom of
bracket.
Align wall fixing bracket with
drilled holes ensuring two slots
are positioned at top and single
slot at bottom. Screw 4 off 1.5’’
screws with washers (provided)
into wall using a screw driver.
Using a 7mm diameter
masonry bit, drill 4 off holes
into wall. Place a plastic
anchor provided into each
drilled hole.
1. 2. 4 .3.
EMPTYING YOUR NEXUS 8G
Open lid as shown above. Unhook sack from lugs and lift
sack out of container.
7. 8.
LOCKING/UNLOCKING YOUR NEXUS 8G
The Confidential Paper model
comes complete with push
lock located on front of
container. With lid closed, push
lock centre to lock unit.
Using key provided unlock
container. (Lock is
available as an optional
extra on all models.)
5. 6.
13. 14. 15. 16.
ATTACHING A GRAPHIC HOLDER TO YOUR NEXUS 8G
Open lid and position graphic
holder at rear of container so
that the holes are aligned with
holes in container.
Place graphic behind clear
polycarbonate sheet and slide into
graphic holder so that lugs locate into
slots along bottom of graphic holder.
From inside of container, place 4 off screws with washers
provided through holes and fix on back of container with
washers and nyloc nuts (using your fingers.) Using a 10mm
wrench and allen key tighten nuts until secure.
9. 10. 11. 12.
INSERTING GRAPHIC
Holding container up to wall
bracket, place 4 off M6 x
16mm screws and washers
provided through holes on
inside of container and fix
with nyloc nuts using your
fingers. Using a 10mm
wrench and allen key
provided tighten nuts until
secure.
PERMANENT WALL FIXING KIT
Using wall fixing bracket as
template, mark out 4 off drill
holes at top and bottom of
bracket.
Align wall fixing bracket
with drilled holes and screw
4 off M5.5 x 50mm screws
provided into wall using
security allen key.
Using a 7mm diameter
masonry bit, drill 4 off holes
into wall. Place a plastic
anchor provided into each
drilled hole.
13. 14. 15. 16.
With the 3 off brackets
already attached to the
container, hook the
container onto wall bracket
so that the hooks locate into
the slots.

All CMYK Versions
White
AND NEXUS®ARE TRADEMARKS OF GLASDON GROUP OR ITS
SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES
Issue 3 August 2011 C000/0382
©Copyright 2013
Glasdon reserve the right to alter specications without prior notice.
Glasdon, Inc.
5200D Anthony Road
Sandston
VA 23150
Sales Inquiries: 1-855-USGLASDON
General Inquiries: 804-726-3777
Fax: [phone]
E-mail: [email protected]
Web: www.glasdon.com
HB256/65
nA planned maintenance schedule of regular inspection is recommended,
replacing components as necessary.
nReplacement components are available direct from GLASDON, Inc.
nGLASDON, Inc. cannot be held responsible for claims arising from
incorrect installation, unauthorized modications or misuse of the
product.
LIFT OFF WALL FIXING KIT
OPENING YOUR NEXUS 8G
Using finger lip at front of lid,
lift lid upwards.
Lift lid to upright position
until it is held by stay
feature.
SECURING SACK IN POSITION
Stretch sack and hook over side
and front lugs so that sack does
not over hang body of
container. Close lid securing
sack in position.
With lid open, install correct
size sack (approx 13 " x 21" x
23½ " available from Glasdon)
by firstly hooking onto
retention lugs at back
of container.
Using wall fixing bracket as
template, mark out 4 off drill
holes at top and bottom of
bracket.
Align wall fixing bracket with
drilled holes ensuring two slots
are positioned at top and single
slot at bottom. Screw 4 off 1.5’’
screws with washers (provided)
into wall using a screw driver.
Using a 7mm diameter
masonry bit, drill 4 off holes
into wall. Place a plastic
anchor provided into each
drilled hole.
1. 2. 4 .3.
EMPTYING YOUR NEXUS 8G
Open lid as shown above. Unhook sack from lugs and lift
sack out of container.
7. 8.
LOCKING/UNLOCKING YOUR NEXUS 8G
The Confidential Paper model
comes complete with push
lock located on front of
container. With lid closed, push
lock centre to lock unit.
Using key provided unlock
container. (Lock is
available as an optional
extra on all models.)
5. 6.
13. 14. 15. 16.
ATTACHING A GRAPHIC HOLDER TO YOUR NEXUS 8G
Open lid and position graphic
holder at rear of container so
that the holes are aligned with
holes in container.
Place graphic behind clear
polycarbonate sheet and slide into
graphic holder so that lugs locate into
slots along bottom of graphic holder.
From inside of container, place 4 off screws with washers
provided through holes and fix on back of container with
washers and nyloc nuts (using your fingers.) Using a 10mm
wrench and allen key tighten nuts until secure.
9. 10. 11. 12.
INSERTING GRAPHIC
Holding container up to wall
bracket, place 4 off M6 x
16mm screws and washers
provided through holes on
inside of container and fix
with nyloc nuts using your
fingers. Using a 10mm
wrench and allen key
provided tighten nuts until
secure.
PERMANENT WALL FIXING KIT
Using wall fixing bracket as
template, mark out 4 off drill
holes at top and bottom of
bracket.
Align wall fixing bracket
with drilled holes and screw
4 off M5.5 x 50mm screws
provided into wall using
security allen key.
Using a 7mm diameter
masonry bit, drill 4 off holes
into wall. Place a plastic
anchor provided into each
drilled hole.
13. 14. 15. 16.
With the 3 off brackets
already attached to the
container, hook the
container onto wall bracket
so that the hooks locate into
the slots.