Glasdon Orion User manual

1
NOTE: ENSURE THAT ALL RELEVANT PERSONNEL READ THE POINTS LISTED WITHIN THIS LEAFLET AND THAT A COPY
INSTALLATION AND MAINTENANCE OF THIS PRODUCTIS GIVEN TO STAFF INVOLVED WITH THE
Opening Shutter/Cover
For a unit with locks, unlock the two padlocks at
the bottom of the shutter and remove. Release
the lock catch from the shutter/cover.
Using either the large handle at the bottom of the
shutter/cover or the handle in the centre of the
Rollatec cover, lift upwards until it is completely
open. At the base of the unit lift the two lock
catches so that they are folded neatly inside the unit.
To close, firstly release the lock catches at the base
of the unit so that they are protruding out of the
unit. Using the large handle, pull the shutter
downwards until it is completely closed ensuring
that your feet are not in the way.
Lift the lock catches upwards to locate with the
bracket on the shutter/cover. Feed the padlock
through the hole in the bracket and lock.
1. 2.
3. 4.
5. 6. 7.
Attaching Personalisation Display Stand(s) to the Storage Unit
Align the stand with the four post
mould inserts on top of the storage
unit. Ensure that the 3 off slots on the
stand are facing the front of the unit.
Place M6 x 20mm screw through
M6 x 14mm washer provided
and insert into each of the four
holes. Tighten using your fingers.
Using the 4mm allen key provided
tighten and secure each fixing in
position.
Closing Shutter/Cover
IMPORTANT NOTE: The unit has been designed to be located against a wall and there is a recessed area
at the rear of the unit to accept the roller shutter in the open position. Do not place your hands down
the recess. See warning sticker on the rear of the unit.

2
Glasdon U.K. Limited
Preston New Road
BLACKPOOL
Lancashire FY4 4UL
Tel: [phone]
Fax: [phone]
email: [email protected]
web: www.glasdon.com
AND ORION STORAGE UNITARE TRADEMARKS OF GLASDON GROUP OR ITS
SUBSIDIARIES IN THE U.K.AND OTHER COUNTRIES
• A planned maintenance schedule of regular inspection is recommended, replacing
components as necessary.
• Replacement components are available direct from GLASDON UK LIMITED.
• GLASDON UK LIMITED cannot be held responsible for claims arising from incorrect
installation, unauthorised modifications or misuse of the product.
Issue 1 December 2013 C000/0456
© Copyright December 2013
Glasdon UK Ltd reserve the right to alter specifications without prior notice.
TM
Cleaning the Unit
We would recommend a warm pressure wash with soap or alternatively hand wash with 10% solution of mild detergent in warm
water using a soft bristle brush followed by a rinse with clean water.
Graffiti
Felt tip pen or paint may be removed from Durapol using a proprietary graffiti remover such as Glasdon Grafitix graffiti wipes.
Carefully follow the instructions, particularly the guidelines covering safety. Ensure that all traces of chemicals are removed then
clean as detailed above.
CAUTION: Graffiti removers can damage stickers, some protection may be afforded by masking off such areas. Please refer
to Technical Services for our recommended graffiti removal supplier.
Maintenance
A planned maintenance schedule of regular inspection is recommended and
components replaced when necessary.
INSTRUCTIONS FOR CONCRETE FIXING KIT
(INTO PREPARED CONCRETE FOUNDATION)
DISTANCE FROM EDGE OF FOUNDATION TO CENTRE OF GROUND BOLT
TO BE NO LESS THAN 110MM
Permanently sited onto a prepared concrete ground site (20-30N/mmsq) utilising 4
M10x140mm ground fixing bolts. Note: The ground fixing kit is an optional extra.
1) Position unit onto siting area ensuring it is the correct distance away from the
edge of the concrete (minimum 110mm) and is in the correct orientation.
2) From the inside of the unit mark hole positions onto the concrete through the
fixing holes in the base with a 10mm diameter masonry drill. Remove the unit.
3) Using a 10mm diameter masonry drill bit, drill and clean out anchor holes to a
minimum depth of 150mm. Position unit back over the drilled holes.
4) Assemble the ground bolts as shown in diagram opposite by removing the
20mm washer and replacing it with the 50mm washer. Drive the ground bolts
through the holes in the base of the unit and into the holes in the concrete.
5) Tighten nut with correct spanner until fixings are secure. Max recommended
torque setting - 20lbs/ft (27Nm). Place the 4off bungs provided over the fixings
to create a smooth surface for ease of cleaning.
6) In the event of the unit being removed, simply remove the bolt to leave the site
hazard free. NOTE: For alternative fixing methods please contact us for details.
IMPORTANT NOTE: TO ENSURE A SECURE AND ROBUST INSTALLATION THE UNIT SHOULD BE SITED ONTO A
SOUND CONCRETE FOUNDATION AND THE 50MM DIAMETER WASHER MUST BE USED. WE STRONGLY
RECOMMEND THAT THE UNIT IS NOT INSTALLED ONTO TARMAC OR BLOCK PAVED AREAS.
Inserting/Removing Poster(s) - Accepts LAMINATED 2 x A4 landscape paper/card posters or a
636mm x 230mm laminated poster. For permanent signage an adhesive graphic can be
adhered to the stand.
Slide clear polycarbonate cover
upwards and remove from stand. Place one or two laminated
posters onto the stand. Place clear cover back over the stand so that it hooks over the top
and the three tabs sit in the slots.
8. 9. 10.
150mm
Concrete base
Base
Bung
Base
M10 x 140mm Ground Fixing Bolt
M10 x 50mm washer