Global Industrial Tri-Temp User manual

globalindustrial.ca
Distribucion Industrial Globales S DE RL DE CF
Instruction Manual Manual de Instrucciones Manuel d'instruction
Customer Service
US: 1-800-645-2986
Servicio de atención al Cliente
México: 01.800.681.6940
Service à la clientèle
Canada: 888-645-2986
1
1. Prior to use, the dispenser must be set-up and installed in
accordance with this manual.
2. This unit is intended for water dispensing only. DO NOT
use other liquids. DO NOT use for other purposes. Never
use any other liquid in the dispenser other than known and safe
tap water in accordance with local safe drinking water regulations.
3. This dispenser is for Indoor use only. Install and use only on
a hard, flat and level surface. Keep the dispenser in a dry
place away from direct sunlight.
4. DO NOT install or store in extreme heat or freezing temperatures.
5. DO NOT place the dispenser in an enclosed space or cabinet.
6. DO NOT operate in the presence of explosive fumes.
7. Position back of the dispenser no closer than 4 inches
from the wall. Permit free airflow between the wall and the
dispenser. There must be at least 4 inches clearance on the
sides of the dispenser to permit airflow.
8. The dispenser is intended to be plugged into a ground
fault circuit interrupter (GFCI) receptacle.
9. Do not use extension cord with your water dispenser.
10. Always grab plug and pull straight out from the outlet. Never
unplug by pulling on the power cord.
11. Do NOT use dispenser if the power cord or plug is damaged.
12. To protect against electric shock, do NOT immerse cord,
plug, or any other part of the dispenser in water or other liquids.
13. The dispenser must be unplugged before cleaning.
14. Never allow children to dispense hot water without proper
supervision.
15. Keep dispenser upright. If the unit is placed on it’s side or is
leaning more than 45°, place it upright and let is stand for 24 hours
prior to operation.
Read this manual thoroughly prior to installation, operation or maintenance.
Failure to execute the instructions in this manual can cause personal injury or property damage.
Water dispenses at a very high temperature. Failure to use properly can cause personal injury.
Keep these instructions for future reference. For questions, visit globalindustrial.com
or contact Customer Service at 1 [phone].
Tri-Temp UV Water Dispenser
Model 670436
WARNING: When operating the dispenser, always follow
these safety precautions:

Instruction Manual
2
Tri-Temp UV Water Dispenser
SET UP & OPERATION
Note: Always connect to a water main that supplies
drinking water only.
Note: Filter (model 761014) sold separately.
1. Place the dispenser upright.
2. Position the unit at least 4 inches away from the
wall on all sides (rear, left and right).
3. Turn off water supply.
4. Connect one end of the 10-ft 1/4” PE water line to
the water inlet connection of the filter head.
5. Connect the other end of the 10-ft water line to the
water supply using the 1/2” water supply adapter.
6. Connect the 3-ft 1/4” PE water line to the water
outlet connection of the filter head.
7. Connect the other end of the 3-ft water line to the
water tank.
8. Turn on water supply and check for leaks.
9. Plug power cord into outlet. Wait at least 10
minutes before operating hot and cold water taps.
9. For initial use, flush all lines clean before consum-
ing. Place a bucket under the taps, press and hold
down all water activation buttons until water flows
out. Note: Initial water flow may have sputter due to
air in the water lines; this will be eliminated once air
is purged from all water lines.
MAINTENANCE
NOTE: Before performing maintenance, unplug the
unit. Cleaning should be done every 3 months.
Parts List
General Cleaning
1. Use a vacuum to clean the condenser. Use a
clean wet cloth to remove dirt from the unit, taps and
especially the condenser.
2. Empty and clean drip tray as needed.
Water tank cleaning
1. Fill the main water tank with water.
2. Add one to two teaspoons of liquid chlorine
bleach. Let stand for five to 10 minutes.
3. Open the drain valve and drain the water using a
bucket.
4. Let the water from filters refill tank and drain a
second time.
5. Also drain the water from the spout using the hot
and cold water taps.
Note: Upon completion of cleaning, wait at least 10
minutes after the power cord is plugged in before
turning on the hot and cold water buttons.
TROUBLESHOOTING
Problem Solution
Water is not coming out
of the taps.
Make sure all water lines are
connected properly.
Cold water is not cold.
It takes up to one hour after setup
to dispense cold water.
Make sure the unit is plugged in
and the cold water switch is on.
Excessive use of cold water; wait
a few minutes for water to chill.
Clean the condenser.
Hot water is not hot.
It takes up to one hour after setup
to dispense hot water.
Make sure the unit is plugged in
and the hot water switch is on.
Dispenser is noisy.
Place the dispenser on a level,
flat surface.
Excessive use of hot water; wait
a few minutes for water to reheat.
SPECIFICATIONS
Voltage:
Heating Power:
Cooling Power:
Heating Capacity:
Cooling Capacity:
Refrigerant:
Climate Type:
Weight:
Dimensions:
Frequency:
110-120V
420W
100W
1.3 G/h
0.5 G/h
R134a
ST
48.5 lbs.
14.6”L x 16”W x 45”H
60Hz
Hot Water Temperature:
Cold Water Temperature:
≥ 194°F (90°C)
≤ 50°F (10°C)
No. Name No. Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Power Indicator
Heating Indicator
UV Indicator
Cooling Indicator
Water Spouts
Night Light
Drip Tray
Door
Cooling Switch
Heating Switch
Power Cord
Drain Valve
Water Inlet
Night Switch