Globalmediapro IP01F User manual

Ethernet Extender
User Manual
Model：IP01F
Ethernet to Fiber Media Converter/Extender

Introduction
IP01F is a networking device capable of transmitting data communication protocol including Ethernet,
Fast Ethernet, and Gigabit Ethernet over fiber optics. The transmission distance can reach up to 20km
over a single-mode fiber module and single-core fiber cable. The plug and play media converter is an
ideal solution for CCTV network, AVoIP system, and IT infrastructure.
Features
●Supports inter-conversion between 10/100/1000Base-TX and 1000Base-SX.
●Supports full/half-duplex.
●Transmission distance up to 20KM via single-mode single-core fiber cable.
●Built-in SC optical connector.
●Supports IGMP, and jumbo frames.
●Supports multiple mounting options (Wall/Rack mounting & Din-rail).
Diagram
※Other than PC, it can also connect a Gigabit Ethernet switch.
Transmission Distance
Module
Cable
Max. Distance
Single-mode
Single-core Fiber (9/125µm)
20㎞
N/A
CAT.5e UTP/ STP/ FTP/ CAT.6 UTP
100m
1

Panel View
No
Interface
Description
1
Power Input
To input a DC5V power
2
RJ45
To connect a network cable
3
SC Fiber Connector
To connect a single fiber cable
4
LED Indicators
To indicate the status of power and connection
LED Indication
LED
LED Status
Description
FX/ACT
Blink
Data Transmitting
TP/ACT
Blink
Data Transmitting
PWR
ON/ OFF
Power On/ Off
Caution
●Transmission distance may vary by cable quality, installation, and connected equipment.
●Using CAT.5e UTP/ STP/ FTP, and CAT.6 UTP (Solid Conductor) cables are recommended, the
greater the diameter of the cable, the fewer the signal and power loss.
●To enable Jumbo frame, both Tx and Rx devices should enable the function at the same time.
2

Package Includes
No
Item
Quantity
1
IP01FA
x 1
2
IP01FB
x 1
3
DV5V 2A Power Adapter
x 2
4
Accessory Set
x 2
3

Specification
Item No
IP01F
Support
Compliance
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-T
IEEE802.3ab 1000BASE-T
IEEE802.3z 1000BASE-SX/1000BASE-LX
IEEE802.3az
Max. Transmission Distance
Ethernet: 100M over a network cable
Fiber: 20㎞ over single mode single fiber
Data Bandwidth
10/100/1000Mbps
Jumbo Frame
9K
Flow Control
Half/ Full Duplex
ESD Protection
15kV (Air), 8kV (Contact)
Ports & Interfaces
Data Input
1 x RJ45 (Auto-MDI/MDI-X)
Data Output
1 x SC Connector (9/125um)
Power
Power Input
DC5V 1A
Power Consumption
<5W
Ambient Temperature
Operation
-40 to 75℃
Storage
-40 to 85℃
Working Altitude
2000M
Humidity
Up to 95%
Physical Characteristics
Dimension
50 x 93 x 32mm
Weight
405g
4

5

Installation Guide
Accessory
A
Machine Screw
B
Self-drilling Screw
C
Screw Plug
D
Angle Bracket
E
DIN-rail Mounting Plat
F
1U Rack
6

Installed on a Platform
Step 1 Use machine screws to fix angle brackets on both sides of your product
Step 2 Use self-drilling screws to fix the product on a platform
7

Step 3 Move the product to get fixed and then lock the screws
8

Installed on Wall
Step 1 Same way as “Installed on a Platform”, but need to put screw plugs into the pilot hole before
inserting the screws (leave 2mm space from the platform)
Installed on a DIN-rail
Step 1 Use machine screws to fix a DIN-rail mounting plat on the side of your product
9

Step 2 Install your product on a DIN-rail as following instruction
Installed on a Rack
Step 1 Lock machine screws in the rack
Step 2 Put your products on the rack
10

Step 3 Push the products to the other side of the rack
Step 4 Install the rack in a cabinet
11