GLOCK PRECISION User manual

OPERATING INSTRUCTIONS
CHRONOGRAPH
Movement Cal. 5030.D & 5021.D

2
DESCRIPTION OF THE DISPLAY AND CONTROL BUTTONS
SETTING THE TIME
Display Elements Control Buttons
* Pull out the crown to position III (the
watch stops).
Turn the crown until you reach the correct
time,8:45.
* Push the crown back into position I.
Please note: * In order to set the time to the
exact second, must be pulled out when
the second hand is in position «60». Once
the hour and minute hands have been set,
must be pushed back into position Iat
the exact second.
Second Hand
Push Button A
Crown
Push Button B
Minute Hand
Hour Hand
Second Counter
Minute Counter
Hour Counter
(only 5030.D)
Date 5021.B
Date 5030.D

3
SETTING THE DATE (QUICK MODE)
SETTING THE DATE/TIME FOLLOWING A BATTERY CHANGE
Example:
• Date/time on the watch: /1:25 AM
• Present date/time: /8:30 PM
Pull out the crown to position II (the
watch continues to run).
Turn the crown until yesterday’s date
appears .
Example:
Pull out the crown to position II (the watch
continues to run).
Turn the crown until the correct date 
appears.
Push the crown back into position I.
Please note: During the date-changing
phase between approx. 9 PM and midnight,
the date must be set to the date of the
following day.

4
BASIC FUNCTION (START/STOP/RESET)
Example:
Start: Press push button A.
Stop: To stop the timing, press push
button Aonce more and read the
chronograph hands: 1 h/20 min/38 sec.
Zero positioning: Press push button
B. (The chronograph hands will be reset
to their zero positions.)
* Pull out the crown to position III (the
watch stops).
Turn the crown until the correct date
appears.
** Continue to turn the crown until the
correct time of 8:30 PM appears.
Push the crown back into position I.
Please note: * To set your watch to the exact
second, please refer to the chapter entitled
«SETTING THE TIME».
** Please observe the AM/PM clock rhythm.

5
Example:
Start: (start timing)
Stop: (e.g., 15 min 5sec following )
Restart: (timing is resumed)
*Stop: (e.g., 5 min 12 sec following )
= 20 min 17 sec
(The accumulated measured time is shown.)
Reset: The chronograph hands are
returned to their zero positions.
ACCUMULATED TIMING
INTERMEDIATE OR INTERVAL TIMING
Example:
Start: (start timing)
Display interval: e.g., 20 min 17sec
(timing continues in the background)
* Making up the measured time:
(The chronograph hands are quickly
advanced to the ongoing measured
time.)
Stop: (Final time is displayed)
Reset: The chronograph hands are
returned to their zero position.
Please note: *Following , further intervals
or intermediates can be displayed by
pressing push button B (display interval/make
up measured time, ...).
Please note: * Following , the
accumulation of the timing can be continued
by pressing push button A (Restart/Stop,
Restart/Stop, …).

6
Adjusting the hour counter hand at 5030.D (position 6h)
Single step A 1 x short
Continuous A long
Adjusting the minute counter hand (position 9h)
Single step A 1 x short
Continuous A long
ADJUSTING THE CHRONOGRAPH HANDS TO ZERO POSITION
Adjusting the second counter hand
Single step A 1 x short
Continuous A long
Example:
One or several chronograph hands are not
in their correct zero positions and have to be
adjusted (e.g., following a battery change).
Pull out the crown to position III (all
chronograph hands are in their correct or
incorrect zero position).
Keep push buttons A and B depressed
simultaneously for at least 2 seconds (the
second counter hand rotates by 360°
corrective mode is activated).
Returning the crown to position I
Termination of the chronograph hands adjustment (can
be carried out at any time).
Adjusting the next hand B
Adjusting the next hand B