Go-Go Babyz gogo Kidz User manual

gogo Kidz™ Travelmate
Safety, Assembly &
Operating Instructions
Model #UNI06
Go-Go Babyz Corporation

EXPRESS LIMITED WARRANTY
Go-Go Babyz Corporation (“Go-Go Babyz”) warrants this product to be free from
defects in materials and workmanship for a period of one year from the date of
purchase. Go-Go Babyz will repair or replace, at its sole option, the defective
product within that one-year time period.
If you have a problem with your Go-Go Babyz product or are not satisfied with it,
please contact Go-Go Babyz Customer Service at 1.888.686.2552.
This express limited warranty does not cover:
(1) Pick-up, delivery, or freight charges.
(2) Corrosion caused by improper storage or failure to reasonably protect the
product from salt water and adverse conditions.
(3) Deterioration due to lack of maintenance and cleaning as specified in the
product instructions.
Go-Go Babyz SHALL NOT BE LIABLE FORANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING FROM BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT. ANY IMPLIED WARRANTY,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS
FOR A PARTICULAR PURPOSE, IS LIMITED TO THE DURATION OF
THE EXPRESS, LIMITED WARRANTY (ONE-YEAR FROM THE DATE OF
PURCHASE).
Under no circumstance shall any liability of Go-Go Babyz under this Express
Limited Warranty, or otherwise, exceed the price of the defective product or parts.
Note: Some states do not allow the exclusion or limitation on incidental or
consequential damages, so the above limitation may not apply to you. Some
states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you.
This Express Limited Warranty gives you specific legal rights, and you may have
other rights, which vary from state to state.
CONTACT GO-GO BABYZ' CUSTOMER SERVICE FOR INFORMATION AND
ALL RETURNS:
Go-Go Babyz Returns
7011 Realm Drive, Suite A5
San Jose, CA 95119
408.360.0653
WARRANTY
ii
Warranty

Safety .. ..................................................................................4
What's Included ..............................................................................6
Parts for assembling the gogo Kidz .........................................6
Parts for attaching the gogo Kidz ............................................6
Handle Assembly ............................................................................7
General Information for Attaching the gogo Kidz ............................8
General Instructions for Attaching the gogo Kidz ........................... 9
Instructions for Attaching to Britax®& Fisher Price®...............10
Instructions for Attaching to Recaro®.......................................11
Instructions for Attaching to the Evenflo Triumph....................12
Commercial Airlines, Car Seats and the gogo Kidz Travelmate....13
Care and Maintenance..................................................................14
TABLE OF CONTENTS iii
Table of Contents

Safety DO NOT USE the gogo Kidz™ Travelmate until you
read and understand these instructions. Your child’s
safety depends on you reading and following these
instructions.
!WARNING: NEVER LEAVE CHILD UNATTENDED.
!WARNING: AVOID SERIOUS INJURY FROM FALLING OR
SLIDING OUT. ALWAYS USE CAR SEAT RESTRAINT SYSTEM.
Be sure to follow the manufacturer’s instructions on how to
properly secure your child in their car seat.
!WARNING: DO NOT EXCEED WEIGHT AND SIZE LIMITATIONS
OF THE CAR SEAT MANUFACTURER OR 50 LBS. MAXIMUM.
This product is to be used as an add-on to you toddler car
seat. The warnings and instructions are in addition to the
safety manual provided by your car seat manufacturer.
!WARNING: DO NOT LEAVE THE GOGO KIDZ ATTACHED TO A
CAR SEAT WHILE DRIVING IN AN AUTOMOBILE. THE GOGO KIDZ
HAS NOT BEEN TESTED IN COMBINATION WITH THE CAR SEATS
IN ANY CRASH TESTING PROGRAM AND INJURY TO YOUR CHILD
COULD OCCUR.
!WARNING: TO AVOID INJURY, KEEP CHILD AWAY FROM
TELESCOPING HANDLE AND THUMBSCREWS. THIS IS NOT A TOY.
!WARNING: ALWAYS ENSURE THUMBSCREWS ARE TIGHT
WHENEVER THE GOGO KIDZ IS ATTACHED TO THE CAR SEAT.
Injury to your child could result if the unit were to come off
accidentally when traveling with your child.
The thumbscrews may loosen over time or have been
loosened without a parent's knowledge. Always check the .
thumbscrews prior to using the gogo Kidz.
!WARNING: DO NOT USE WHILE EXERCISING
Do not use this product while running, jogging, in-line
skating or participating in other athletic activities.
SAFETY
4

SAFETY 5
!WARNING: EXCESSIVE WEIGHT, PARCELS, OR ACCESSORY
ITEMS PLACED OR HUNG ON THE HANDLE MAY CAUSE THE UNIT
TO BECOME UNSTABLE.
Do not place parcels or accessory items on the handle in
excess of 3 pounds.
Do not allow children to play with or hang onto the gogo
Kidz.
!WARNING: DO NOT ALLOW CHILDREN TO CLIMB INTO OR OUT
OF THE CAR SEAT WHILE GOGO KIDZ IS SECURED, UNLESS YOU
ARE HOLDING THE GOGO KIDZ AND INSTRUCTING THE CHILD.
!WARNING: NEVER USE THE GOGO KIDZ ON STAIRWAYS OR
ESCALATORS.
!WARNING: THE GOGO KIDZ IS DESIGNED TO ROLL.
Make sure the front of the car seat is on the floor and the
entire unit is on a flat surface before letting go of the handle.
Accessories which are not approved by the manufacturer or
distributor should not be used.
!WARNING: PLASTIC MATERIAL WILL WEAKEN OVER TIME IF
EXPOSED TO EXCESSIVE HEAT OR LIGHT. USE OF THIS PRODUCT
SHOULD BE DISCONTINUED 5 YEARS FROM THE DATE OF
MANUFACTURER, AS SHOWN ON THE PRODUCT.
Safety

What's Included Please refer to this page during any part of the assembly
instructions and attaching instructions.
You will use the following parts to assemble the gogo
Kidz™ Plate:
1 Plate with axle, wheels and push caps already assembled
1 Handle
2 Handle Screws
You will use the following parts for attaching the gogo
Kidz™ Plate to:
Britax® & Fisher-Price®:
2 Thumbscrews You will find the thumbscrews located in the
retainer bar.
1 Retainer Bar
Evenflo® Triumph™:
1 Long Strap Please remove the cleats and o-rings from the
short strap
2 Cleats and O-Rings
2 Thumbscrews You will find the thumbscrews located in the
retainer bar. They have been inserted into the
retainer bar for quality assurance. Please
remove from retainer bar prior to any assembly.
Recaro®:
2 J-Bolts & Located is a separate bag.
Thumb Nuts
Most other car seats:
1 Short Strap
2 Cleats and O-Rings
2 Thumbscrews You will find the thumbscrews located in the
retainer bar. They have been inserted into the
retainer bar for quality assurance. Please
remove from retainer bar prior to any assembly.
WHAT'S INCLUDED6
Plate with axle, wheels and
push caps
Handle screws
Thumbscrews
Strap with cleat and o-ring
Retainer bar - for use with
Britax®
Handle
J-Bolts with
Thumb nuts
- for use with
Recaro®

The gogo Kidz™ Travelmate comes pre-assembled
except for the handle. Please follow the instructions
below to assemble the handle.
A Phillips Head Screwdriver is all that is needed to
assemble the handle.
NOTE: It is important that the handle be orientated properly before
insertion into the openings of the gogo Kidz plate. There are two ways to
make sure the handle is inserted correctly. 1. There is a rivet in each leg
of the handle (at the bottom on one side). There is a corresponding slot in
the plate that allows the rivet to pass through and still provide a tight fit. 2.
Lining up the screw holes in the handle and plate.
1. Insert the handle.
Locate the side of the handle with the pre-drilled holes at the base.
Insert the handle into the openings of the gogo Kidz plate, aligning
the handle holes to the holes in the plate. Make sure the handle is
pushed in all the way to the base of the opening. You may use a
rubber mallet if needed to hammer the handle into the plate.
2. Fasten handle to the gogo Kidz plate.
Find the two screw holes on the front of the plate and firmly secure
each screw into the existing hole, allowing the screw to go through
the metal of the handle. You may use an electric screw driver if
desired. Secure them tightly, but do not over tighten. The screws
are to prevent the handle from sliding out of the pocket.
NOTE: Drilled holes in the handle may not align exactly with the holes in
the plate. This is okay. At first the screw may go in at an angle but it will
straighten itself out as you tighten.
IMPORTANT
3. Secure the connection.
Once you have screwed the handle to the plate, pull up on the
handle to ensure it is secure.
4. Test the handle.
Open the handle by pushing on the release button located at the
top of the handle and test the handle by locking it in the bottom
and top positions a few times prior to proceeding onto attaching the
gogo Kidz Travelmate to a car seat.
HANDLE ASSEMBLY 7
Handle Assembly
Phillips Head Screwdriver
Handle screws
Back of the plate with inserted
handle.
Front of plate with handle
inserted and one screw
inserted

General Attaching
Information You may use the general instructions below as a quick
start guide for attaching the gogo Kidz™ Travelmate to
your car seat.
Most car seats have two ribs that go from top to bottom on the back
of the car seat with a space between them. The handle area on
the back of the gogo Kidz plate goes between the ribs in the space
with the smooth, front side of the plate facing out.
Align the two support tabs on the bottom of the gogo Kidz plate at
the bottom of the ribs to help support the car seat.
Lay the gogo Kidz plate on the back of the car seat. The wheels
should be able to rotate freely.
Use appropriate attachment (i.e. short or long strap, retainer bar or
j-bolts) and fasten to the plate and car seat.
NOTE: Some car seats do not have these two long ribs in the back. For
these types of seats, the support tabs on the bottom of the gogo Kidz
should be located underneath the base itself.
NOTE: You may be required to move the bar on the back that adjusts
shoulder straps to allow the handle to sit properly.
NOTE: The seat recline angle may have to be adjusted to make room for
the support tabs or the wheels on some seats.
Attach the tether strap to the handle of the gogo Kidz plate to
ensure the gogo Kidz is secure.
RECOMMENDED CAR SEATS
The gogo Kidz™ Travelmate will accommodate most convertible
and toddler car seats. Please refer to the list of recommended car
seats, located on the back page, to ensure a safe fit. Go-Go Babyz
is continually testing new seats with the gogo Kidz and will update
our web site frequently whenever we discover a new match or to
confirm which seats will not fit with the gogo Kidz. If you do not see
your car seat listed on the product box or manual, please check our
web site to see if we have had to opportunity to test it with the gogo
Kidz.
GENERAL INFORMATION FOR ATTACHING THE GOGO KIDZ TO A CAR SEAT8
Attaching the tether clip to the
gogo Kidz
Arrows pointing to support tabs
Arrows pointing to car seat ribs

General Attaching
Instructions
9
Adjusting the cleat on the strap
Make sure tabs align with ribs
at the bottom of the car seat.
Use opening if available
Leave thumbscrew loose until
you begin threading opposite
side, and then tighten
Instructions below are for attaching to Cosco®, Eddie
Bauer® , Evenflo®, Graco® & Safety 1st® car seats. If
you are using a Britax®, Fisher-Price®, Evenflo® Triumph™
or a Recaro® car seat, please refer to the appropriate
section.
You will use two thumbscrews, the short strap with two
cleats attached by two o-rings and the tether strap from
the car seat.
1. Place the seat face down on the floor.
2. Align the plate.
Align the two support tabs on the back side of the gogo Kidz plate to the
bottom of the car seat and lay the gogo Kidz plate on the back of the car
seat. (Please refer to general information if you are having difficulty)
3. Attach the strap.
Begin by securing the end of the strap that has only one grommet to either
the left or right side of the gogo Kidz plate. Insert a thumbscrew into the
highest hole possible on the plate and thread the thumbscrew into the
cleat. The strap should be in between the plate and the cleat. Leave the
strap loose because you will tighten it later. Make sure the strap is not
twisted. Once one side is attached, thread the strap through the seat belt
opening of the car seat.
NOTE: The cleat can be relocated if necessary to fit the needs of your
particular car seat. To change the location of the cleat, remove the o-ring
that attaches the cleat to the strap. Place the cleat over the proper hole
and replace the o-ring.
6. Attach the other side of the strap.
Insert the thumbscrew into the other side of the plate, at the same height
as the first side. Begin threading thumbscrew into the cleat. Retighten the
first thumbscrew until it is almost flush with the plate Then retighten the
second thumbscrew again.
7. Test the connection.
Once the strap is tightened, lift the car seat and gogo Kidz into the upright
position and test the connection by pulling on the handle and moving the
gogo Kidz side to side. Retighten the strap.
8. Attach the tether strap.
The tether strap is connected to the car seat and attached onto the handle
of the gogo Kidz plate (as shown on the general information page).
NOTE: ALWAYS SECURE YOUR CHILD WITH THE SAFETY HARNESS
PROVIDED BY THE CAR SEAT MANUFACTURER.
GENERAL INSTRUCTIONS FOR ATTACHING THE GOGO KIDS TO A CAR SEAT

10
Attaching to the Britax® & Fisher Price® car seats
NOTE: The gogo Kidz does not attach to the Britax® Parkway™
To attach to the Britax® or Fisher-Price® car seats, you
will use two thumbscrews, the retainer bar and the tether
strap from the car seat.
1. Place the seat face down on the floor.
2. Insert retainer bar.
Place the retainer with the flat side lying against the car seat. If you
are using a Wizard® or Boulevard™ car seat, place the retainer bar
above the metal bar on the back of the car seat.
3. Align the plate.
Align the support tabs at the bottom of the gogo Kidz plate with the
bottom of the car seat and lay the gogo Kidz plate on the back of
the car seat.
4. Insert thumbscrews.
Insert the thumbscrews into the two holes located in the center of
the plate and tighten. You may need to hold the bar closer to the
plate with your other hand while screwing in the thumbscrews.
Retighten the first thumbscrew after tightening the second.
5. Test the connection.
Once the retainer bar been attached to the plate and the gogo Kidz
is secure, lift the car seat and pull the gogo Kidz into the upright
position. Test the connection by pulling on the handle and moving
the gogo Kidz side to side. Retighten the thumbscrews as needed.
6. Attach the versa-tether strap.
Pull 10 inches of the “versa-tether” strap from the pouch that is
located on the rear of the seat near the top. Pull the strap over the
handle and tighten the “versa-tether” by pulling on the end of the
tether strap. Place excess strap back into the pouch. Tuck in all
remaining latch and tether straps in order not to get tangled when
in use.
NOTE: ALWAYS SECURE YOUR CHILD WITH THE SAFETY HARNESS
PROVIDED BY THE CAR SEAT MANUFACTURER.
ATTACHING THE GOGO KIDZ TO A BRITAX®OR FISHER-PRICE®CAR SEAT
Attaching to a
Britax® or Fisher
Price® car seat
Shown above on Britax®
Roundabout®
Shown above on Britax®
Wizard®
Looking in from the top of the
seat (above) bottom (below)

Attaching to the
Recaro® car seat
Attaching to the Recaro® car seat
To attach to the Recaro® car seat you will use two j-bolts,
two thumb nuts and the tether strap of the car seat.
1. Place the seat on the floor.
2. Attach the j-bolt.
Hook the j-bolt over the L-shaped metal rod on the side of the
Recaro® seat and align the gogo Kidz plate so the threaded end of
the j-bolt goes through the middle hole on the side of the plate.
3. Attach the Thumb Nut.
4. Repeat steps 2 & 3 for the other side of the seat and plate.
5. Attach the tether strap.
Take the tether strap that is attached to the Recaro® seat and .
pull it all the way out.
Thread the strap through the shoulder strap opening of the car
seat. Refer to seat manufacturers instructions if needed.
Wrap the tether strap around the outside of the gogo Kidz ........
handle and hook the tether clip over the entire strap as shown .
in pictures.
Tighten the strap and pull on it confirm it is secure.
6. Test the connection.
Once the strap is tightened, test the connection by pulling on the
handle and moving the gogo Kidz side to side. Retighten the strap.
NOTE: ALWAYS SECURE YOUR CHILD WITH THE SAFETY HARNESS
PROVIDED BY THE CAR SEAT MANUFACTURER.
ATTACHING THE GOGO KIDZ TO THE RECARO®CAR SEAT 11
Make sure the plate of the
gogo Kidz is positioned evenly
on the back of the car seat.
The support tabs on the
bottom of the plate will just be
touching the bottom of the car
seat.
Hook entire width of the tether
strap.

ATTACHING THE GOGO KIDZ TO THE EVENFLO® TRIUMPH™12
Attaching to the
Evenflo® Triumph™
car seat
Attaching to the Evenflo® Triumph™
To attach to the Evenflo® Triumph car seat you will
use the long strap with two cleats and o-rings, two
thumbscrews, and the tether strap from the car seat.
1. Recline Seat.
Begin by reclining the Triumph seat all the way in the reclined
position. The car seat should be adjusted to lean all the way back
otherwise; the child will end up being too vertical.
2. Attach one end of the long strap to a cleat.
3. Align gogo Kidz plate with car seat.
Rest back of car seat onto the support tabs of the gogo Kidz
Travelmate plate.
4. Attach the long strap.
Attach the strap/cleat to the plate with one thumbscrew by inserting
one thumbscrew into the 2nd or 3rd hole from the bottom of the
plate. Do not tighten, yet.
5. Insert the long strap.
Insert the other end of the strap through the seat belt hole located
at the back of the car seat.
6. Attach the other end of the strap with the second
thumbscrew.
NOTE: Make sure thumbscrews are located in the same position on each
side, and then tighten firmly.
7. Test the connection.
Once the retainer bar been attached to the plate and the gogo Kidz
is secure, lift the car seat and pull the gogo Kidz into the upright
position. Test the connection by pulling on the handle and moving
the gogo Kidz side to side. Retighten the thumbscrews as needed.
8. Attach the versa-tether strap.
Pull 10 inches of the “versa-tether” strap from the pouch that is
located on the rear of the seat near the top. Pull the strap over the
handle and tighten the “versa-tether” by pulling on the end of the
tether strap. Place excess strap back into the pouch. Tuck in all
remaining latch and tether straps in order not to get tangled when
in use.
NOTE: ALWAYS SECURE YOUR CHILD WITH THE SAFETY HARNESS
PROVIDED BY THE CAR SEAT MANUFACTURER.
Recline seat
Attach Cleat
Rest seat onto support tabs
Tighten Thumbscrews

COMMERCIAL AIRLINES, CAR SEATS AND THE GOGO KIDZ 13
Commercial
Airlines, car seats
and the gogo
Kidz™ Travelmate
Does the gogo Kidz™ Travelmate fit down the aisle of
an airplane? Can I leave it attached on an airplane? Any
suggestions about the car seat and the airplanes?
The gogo Kidz is 16 ½ inches wide and fits down the aisle of most
commercial airplanes. However, many car seats are wider and
they may not fit down the aisle of the coach section. A practical
approach is to have your child out of the seat and expect to carry
the seat to your assigned seat, once you reach the coach section.
The handle on the gogo kidz makes this easier to do than carrying
the car seat by itself.
There are dozens of car seat manufacturers with multiple models
of car seats. THE GOGO KIDZ™ TRAVELMATE HAS NOT BEEN
TESTED IN COMBINATION WITH THE CAR SEATS IN ANY
CRASH TESTING PROGRAM. Remove the gogo Kidz and either
stow it in the overhead bin or “gate check it.”
Fortunately, the gogo Kidz is very easy to put on and take off.
Only one thumbscrew needs to be removed for the strap version
and two thumbscrews for the Britax®, Fisher-Price® and Recaro®
seats.
Note: We recommend you remove the strap and keep it with you if
you check the gogo Kidz Travelmate at the gate.
There have been reports of the aircraft seat belt buckle being stuck
behind car seats, creating a removal problem at destination. You
may wish to ask the flight attendant for a seat belt extender to
eliminate the potential for this problem.
Other airplane information
We are updating our web site, www.gogobabyz.com, to include
information and links that offer some very good general information
about traveling with children on airplanes, safety issues and other
practical suggestions. We recommend you take the time to review
this information.

 Before connecting the gogo Kidz to your car seat, make sure
the unit is assembled correctly and all parts and fasteners are
secure.
 After assembly pull horizontally on the back of the gogo Kidz
to make certain the guides are aligned properly and there is no
slippage.
 Confirm that thumbscrews are tight.
 Periodically check that the handle, axle and wheels are secure.
 Replace any damaged parts immediately.
 Clean with a damp cloth and wipe dry.
 Do not store unit outside exposed to rain or extreme sunlight.
 Do not place heavy items on top of unit when storing it.
!WARNING: PLASTIC MATERIAL WILL WEAKEN OVER TIME IF
EXPOSED TO EXCESSIVE HEAT OR LIGHT. USE OF THIS PRODUCT
SHOULD BE DISCONTINUED 5 YEARS FROM THE DATE OF
MANUFACTURER, AS SHOWN ON THE PRODUCT.
CARE AND MAINTENANCE14
Care &
Maintenance

THANK YOU 15
Thank you!
Thank you for your recent order. We wish you many happy travels
with your new gogo Kidz™Travelmate!
Our goal for Go-Go Babyz is to offer innovative, high quality and
safe products to make life easier when you and your baby are “on
the go.”
We welcome suggestions and comments. Go-Go Babyz is
dedicated to making our current products and features easier
to use. Please send ideas for new features, products or general
feedback to us at [email protected].
In addition, we have created a photo gallery on our web site for
families, like us, using Go-Go Babyz products. Please feel free
to email or mail us any photos of you and your children using our
products and we would be happy to share them on our Family
Photo Gallery page.
Thank you again for your purchase. We appreciate your business.
Sincerely,
The Go-Go Babyz Family
Toll Free: 888.686.2552
www.gogobabyz.com

The gogo Kidz™ Travelmate will accommodate most convertible and toddler car seats. Below is a list of
confirmed manufacturer and model names. Go-Go Babyz is continually testing new seats with the gogo
Kidz and will update our web site frequently. If you do not see your car seat listed below, please check our
web site at www.gogobabyz.com
Manufacturer ModelName Manufacturer ModelName
Britax® Fisher-Price®
Roundabout® SafeVoyage™
Marathon™ Graco®
Decathlon™ Toddler SafeSeat™
Boulevard™ ComfortSport™ Convertible
Wizard® Treasured CarGo™ Booster
Advantage™ Recaro
Cosco® Young Sport
Alpha Omega® Elite 5-Point
High Back Booster Safety 1st®
Summit® High Back Booster 3-Phase
Eddie Bauer® Enspira
Summit Booster
Evenflo®
Titan™ Deluxe Convertible Car Seat
Tribute™ 5 Deluxe Convertible Car Seat
Tribute™ VLX
Tribute™ V
Triumph™
Generations™ Booster Car Seat
Harness Booster seat
Chase LX Booster
Go-Go Babyz® & gogo Kidz™ Travelmate are trademarks of Go-Go Babyz Corporation. Britax®, Boulevard™, Decathlon™, Marathon™,
Roundabout® and Wizard® are trademarks of Britax Child Safety, Inc. Cosco®, Alpha Omega®, Summit®, Safety 1st® and Eddie
Bauer® are trademarks of Inc, Dorel Industries, Inc. and/or their affiliates. Evenflo®, Titan™, Tribute™ and Generations™ are trademarks
of Evenflo Company, Inc. and/or their affiliates. Fisher-Price® and Safe Voyage™ are trademarks of Mattel, Inc. Graco®, Toddler
SafeSeat™, ComfortSport™ and Treasured CarGo® are trademarks of Graco Children’s Products. Recaro, Young Sport, Young Export and
Young Style are trademarks of Keiper Recaro Group.
The Go-Go Babyz® product illustrated here is not approved by or manufactured under license from Britax Child Safety, Inc, Dorel
Industries, Inc., Evenflo Company, Inc., Keiper Recaro Group, Mattel, Inc., Graco Children’s Products and/or their affiliates. Go-Go Babyz
Corporation is not affiliated with Britax Child Safety, Inc., Dorel Industries, Inc., Evenflo Company, Inc., Mattel, Inc., Graco Children’s
Products and/or their affiliates.