GO MOTO HJC F70 User manual
GO MOTO CHIN MOUNT
GO SECURE, GO MOTO!
USER MANUAL
Table of content:
The basics
Mounting instructions
Customer support
Mounting Action Camera
Removing mount
WARNING
ALUMINUM ACTION CAMERA MOUNT
ASA HELMET SPECIFIC BASE
The Basics
3M VHB SURFACE CLEANER
ORIGINAL 3M VHB 4991 F ADHESIVE
2.
2
3
5
6
7
8
3.
Mounting instructions.
Before mounting the Go Moto mount
to your helmet, we strongly advise
you to find the optimal placement on
your helmet. To do this, you can refer
to the product photos on our website
for the chin mount and use them as a
guide. It is important to note that you
should not remove the 3M protective
film during this process.
Carefully adjust the mount until all
sides align seamlessly with your
helmet. This will ensure the best fit
and security for your camera.
Step 1 Find the right spot!
If your helmet is really dirty, it is
recommended to clean it with soapy
water first.
Clean the mounting surface on your
helmet with the provided 3M VHB
Surface Cleaner.
This will ensure a strong bond
between the 3M VHB adhesive and
your helmet.
After cleaning the surface, allow it to
air dry for approximately one minute.
Step 2 Clean mounting surface
4.
Gently peel off the protective film from
the 3M VHB adhesive.
To optimize adhesion we recommend
warming up the 3M VHB adhesive
(NOT HOT!) with a hair dryer.
Carefully line up the mount with your helmet
(remember step 1). Avoid applying pressure
until you are confident that the placement is
just right. When you think the mount is on
the right spot, press down firmly and hold for
at least one minute with consistent pressure.
Potential gaps may be present between the
3M adhesive and the helmet. This could be
due to misplacement or not applying enough
pressure.You may want to warm up and
press the chin mount again. Alternatively,
you can use a credit card to gently press the
edges of the 3M adhesive against the
helmet, removing any gaps.
Step 3 Prepare for mounting!
Step 4 Placing the mount
5.
You mounted your Go Moto mount?!
Well done!
Just a little patience...
Before using your Go Moto Mount,
we recommend not using it for at
least 24 hours to let the adhesive
properly cure.
The optimal waiting time for the 3M
VHB adhesive to settle is 72 hours.
We’d love to see your results! Share
your Go Moto mount on Instagram
or Facebook with gomotomounts!
Questions?
Need any help mounting your Go Moto mount, or do you have any other questions? We’ll be
happy helping you out!
www.go-moto.com
gomotomounts
www.facebook.com/gomotomounts
Find Go Moto online!
Step 5 Waiting...
24 hrs
6.
You can mount an action camera mount
by using a compatible mounting buckle.
This will be universal for different brands
including: GoPro Hero/Session, Insta360
ONE R, DJI Osmo Action, Xiaomi Yi 4K
and more.
Carefully align the buckle with the mount
and push it firmly into place until you hear
a clicking sound. This will ensure that the
camera is securely attached to the mount
and will not come loose during use.
Using an extension arm with your
camera mount can provide additional
adjustability and flexibility for achieving
the perfect camera angle. By attaching
the extension arm between the mount
and your camera, you can easily adjust
the angle, height, and distance of the
camera to capture the perfect shot.
Mounting action camera
Adjusting camera angle
7.
Removing the mount from your helmet can be a challenging
task, but it is important to do it correctly to avoid causing any
damage to your helmet or the Go Moto mount. Here are some
tips that can make the process easier and smoother:
We strongly recommend using a hair dryer to warm up the
sides of the mount. This will help to loosen the adhesive and
make it easier to remove the mount from your helmet.
To avoid scratching your helmet, we advise using a soft and
flat object, such as an old credit card, to remove the mount.
Carefully push the credit card between the mount and the
adhesive, starting from the corners, until it starts coming
loose.
When the corners of the adhesive are
released, try twisting the Go Moto
mount (you can attach something to the
mount to get more grip). It is important
to take your time during the removal
process to ensure that the mount and
the adhesive come off cleanly and
without causing any damage. If you
encounter any resistance, stop
immediately and reapply heat to the
area before trying again. By twisting
the mount it should release from your
helmet without causing any damage.
Removing the mount
Step 1 Weakening the adhesive
Step 2 Twisting the mount
8.
WARNING:
Only use the correct Go Moto mount for the intended helmet.
Always clean your helmet with original 3M VHB surface cleaner before mounting the Go Moto mount.
The 3M VHB adhesive may not stick properly without using the 3M VHB cleaner.
Only use original 3M VHB 4991 F adhesive for the Go Moto mount. Any other adhesives may fail to
hold.
Always check your action camera is properly mounted before riding.
Go Moto is not responsible for any damage caused by improper installation.
Be careful when using the mount in high temperatures. At temperatures above 40 degrees, the
adhesive can weaken. Keep the mount out of the sun at high temperatures.
DANGER. 3M VHB surface cleaner:
Contains: Propan-2-ol.
Highly flammable liquid and vapour. Causes serious eye irritation. May cause drowsiness or
dizziness.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
Avoid breathing vapours.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and
easy to do. Continue rinsing.
Table of contents
