SRC B-TRK502-01-01-SL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
No. Description Quantity Torque * (N-m) Remarks **
1 Head Light Guard 1
2 Grommet 4
3 Mounting Pin 4
4 Bracket - RH 1
5 Bracket - LH 1
6 Washer M5 8
7 Screw M5 x 16 2 5 - 6 Use Liquid Thread Locker
8 Screw M5 x 20 2 5 - 6 Use Liquid Thread Locker
9 Screw M5 x 10 4 5- 6 Use Liquid Thread Locker
SRC Design uses Metric System of Measurement and all dimensions are in Millimeters
* Recommended to use the Torque specified in the table
** Denotes Usage of Liquid Thread Locker in specified locations
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: B-TRK502-01-01-SL / B-TRK502-01-02
Part Description: Head Light Guard –BENELLI TRK502 / TRK502 X
Applicable to Finished colour versions of Black and Silver
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
Mounting Instructions
Step 1:
Mounting of Bracket LH (5)
Orient the Bracket LH (5), as
shown, in-line with the two
mounting holes in the Motorbike
on the Left hand side.
Slip-in Washer M5 (6) –2 off, and
M5 x 16 (7) –1 off, M5 x 20 (8) –1
off as shown and secure the
threads in the mounting holes.
Step 2:
Repeat the step on the Right Hand
side, to mount the Bracket RH (4),
as shown.
The Mounting Pin (3), 2 off on
each of the Bracket LH & Bracket
RH, can be assembled off-line.
Slip-in Washer M5 (6) –2 off ,
Screw M5 x 10 –2 off and secure
the Mounting Pin (3), from the
other side, as shown.

Copyright By SRC
Design and Specification are subjected to change
Page 4
Step 5:
Ensure Orientation, Mounting Symmetry of the
Head Light Guard from the front side and
tighten the fasteners to torque as specified in
the BOM table
The Head Light Guard “As is final Mounted
Condition”
Step 3:
Orient the Head Light Guard, as shown,
to the Bracket (LH) and slip-in the
Grommet (2) –2 off, as shown.
The groove in the Grommet will closely
hug the outer surfaces of the Head Light
Guard and holding on to the Mounting
Pin.
Step 4:
Repeat the Step 3 for mounting the Head
Light Guard on the Right hand side.

Copyright By SRC
Design and Specification are subjected to change
Page 5
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and follow the step-by-
step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the Accessory part to the
Vehicle. We have prepared this based on our experience and knowledge, related to the Vehicle, Part and
its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s accessory part. It
is advised to the User, to inspect and ensure the original state of all other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving behaviour and/or the
stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all functions of
the Vehicle. It is always advised to check loosening of the fasteners after the first 50 kilo meters of ride and
at regular intervals.
7. To the maximum extent possible, our design use the current Mounting/Fitment of the Original
Equipment, so that Installation of these accessories will not affect the Payload or Function of the Vehicle or
the Part on which it is mounted to protect it
8. If any additional modifications are to be done, prior to the fitment of the accessories, it will be explicitly
specified in the instruction sheets