Godox QE300 User manual

说 明 手 册
Instruction Manual
中英文双语
Chinese English Bilingual
705-QE0000-00 Made In China
地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋
Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong
Town, Baoan District, Shenzhen 518103, China
电话/Tel: [phone](8062) 传真/Fax: [phone]
邮箱/E-mail: [e-mail]
http://www.godox.com
神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
Professional Studio Flash
专 业 影 室 闪 光 灯

维护保养
闪光灯在工作时，如发现异常，应立即关掉电源，查明原因。
灯体应避免震动，平时注意表面除尘。
灯体稍有发热为正常现象，无特别需要时，勿连续引闪。
除灯管与造型灯消耗品允许用户用原厂配置的自行装卸更换外，闪光灯的其他维护
概由本厂指定可供原厂配件之维修部负责。
1年保修，由于灯管与造型灯为消耗品，不在1年保修范围。
擅自检修此闪光灯，经发现将取消闪光灯之一年保修期，维修需要收取相关费用。
如果本品出现故障或者被水淋湿，唯有在专业人员维修后方可继续使用。
在维修和清洁本品时请断开电源。
如有技术更改，恕不另行通知。
- 07 - - 08 -
FOREWORD
Thanks for choosing QE series studio flash. It is a durable and high-
performance strobe with complete functions to help professional
photographers create desired lighting effects. This product is suited for
wedding, advertisement, portrait, and fashion photography. The perfect light
source and a Must in studios and photo workshops! The QE flash offers:
CONTENTS
08 Foreword
09 For Your Safety
09 Caution
10 Names of Parts
10 Body•
10 Accessories•
11 Separately Sold Accessories•
11 Operations
11 Flash Preparation•
11 Power Connection•
11 Modeling Lamp•
12 Power Output Control•
12 Test Button•
12 Sync Triggering•
12 Slave Trigger Model•
12 Buzz Function•
13 Memory Function•
13 Wireless Control Function•
13 Tube Replacement•
14 Technical Data
14 Maintenance
Precise output control, 30 steps from 5.0-8.0 in 0.1 increments
High-qualified modeling lamp, 150W output steplessly adjustable
Outstanding output stability, a tolerance of ≤ 2% under the same output
Anti-preflash function, enabling synchronization with cameras having a one-
preflash firing system
Automatic power discharge when the flash output is adjusted from high to low
Adjusted parameters intelligently remembered after 3s and automatically
recovered after a restart
Wireless control of the flash power ratio, the on-and-off of modeling lamp and
buzzer, as well as flash triggering

FOR YOUR SAFETY
To prevent damage to the product or injury to you or to others, read the
following safety precautions in their entirety before using this device. Keep
these safety instructions where users can read them for ready reference.
Do not disassemble or modify
There are high-voltage components inside the unit. Failure to observe this
precaution could result in electric shock or product malfunction. Should the
product break open as the result of a fall or other accident, send the defective
back to the authorized service center for inspection and maintenance.
Keep dry
Do not handle with wet hands, immerse in water, or expose to rain. Failure to
observe this precaution could result in fire or electric shock.
Keep out of reach of children
This device contains small parts that may pose a choking hazard. Consult a
physician immediately if a child swallows any part of this device.
Do not expose to high temperature
Do not leave the device in a closed vehicle in the sun or in other areas subject to
extremely high temperature. Failure to observe this precaution could result in fire
or damage to the housing or internal parts.
CAUTION
After 30 continuous flashes at full power, the flash should be cooled down for
about 3 minutes. Overheating will occur if it is used continuously without cooling
down.
Do not keep using the modeling lamp for a long time, otherwise flammable
accessories attaching to flash head, e.g. softbox will get burnt. A 10-minute time
is recommended in this case. After 10 minutes, cool it down for 1 minute.
When using a snoot, do not keep the modeling lamp on for a long time or fire too
frequently (not over six times for one minute). Overheating will result in damages
for strobe housing and/or studio light.
Do not touch the lamp cap when the flash or modeling lamp is working, as it will
give out heat, leading to high surface temperature.
Do not touch the two terminals of the tube outlet as there is high voltage inside.
Wear insolated gloves before replacing the tube or modeling lamp.
Avoid sudden impacts as this can damage the flash tube and/or modeling lamp.
Do not flash directly towards naked eyes (especially those of babies), otherwise
it may lead to visual impairment.
Disconnect from the power supply when it will not be used for an extended
period.
15
4
1
7
17
8
20
14
3
10
2
5
6
11
12
16
18
13
19
Body
NAMES OF PARTS
1. AC Power Socket
2. Sync Cord Jack
3. Power Switch
4. Modeling Lamp Output Controller
5. Flash Output Controller
6. Modeling Lamp Button
7. Sound Button
8. Slave Model Button
9. Test Button
10. Digital Display
11. Modeling Lamp Indicator
12. Buzz Indicator
13. Slave Triggering Indicator
14. Test Indicator Lamp
15. Light Sensor
16. Fuse
17. Wireless Control Port
18. Mounting Bracket
19. Umbrella Input
20. Direction Adjusting Handle
1. Sync Cord
2. Power Cord
3. Standard Reflector
4. Lamp Cover
5. Modeling Lamp
6. Instruction Manual
Accessories
9
- 10 -- 09 -
1 2 345

FOR YOUR SAFETY
To prevent damage to the product or injury to you or to others, read the
following safety precautions in their entirety before using this device. Keep
these safety instructions where users can read them for ready reference.
Do not disassemble or modify
There are high-voltage components inside the unit. Failure to observe this
precaution could result in electric shock or product malfunction. Should the
product break open as the result of a fall or other accident, send the defective
back to the authorized service center for inspection and maintenance.
Keep dry
Do not handle with wet hands, immerse in water, or expose to rain. Failure to
observe this precaution could result in fire or electric shock.
Keep out of reach of children
This device contains small parts that may pose a choking hazard. Consult a
physician immediately if a child swallows any part of this device.
Do not expose to high temperature
Do not leave the device in a closed vehicle in the sun or in other areas subject to
extremely high temperature. Failure to observe this precaution could result in fire
or damage to the housing or internal parts.
CAUTION
After 30 continuous flashes at full power, the flash should be cooled down for
about 3 minutes. Overheating will occur if it is used continuously without cooling
down.
Do not keep using the modeling lamp for a long time, otherwise flammable
accessories attaching to flash head, e.g. softbox will get burnt. A 10-minute time
is recommended in this case. After 10 minutes, cool it down for 1 minute.
When using a snoot, do not keep the modeling lamp on for a long time or fire too
frequently (not over six times for one minute). Overheating will result in damages
for strobe housing and/or studio light.
Do not touch the lamp cap when the flash or modeling lamp is working, as it will
give out heat, leading to high surface temperature.
Do not touch the two terminals of the tube outlet as there is high voltage inside.
Wear insolated gloves before replacing the tube or modeling lamp.
Avoid sudden impacts as this can damage the flash tube and/or modeling lamp.
Do not flash directly towards naked eyes (especially those of babies), otherwise
it may lead to visual impairment.
Disconnect from the power supply when it will not be used for an extended
period.
15
4
1
7
17
8
20
14
3
10
2
5
6
11
12
16
18
13
19
Body
NAMES OF PARTS
1. AC Power Socket
2. Sync Cord Jack
3. Power Switch
4. Modeling Lamp Output Controller
5. Flash Output Controller
6. Modeling Lamp Button
7. Sound Button
8. Slave Model Button
9. Test Button
10. Digital Display
11. Modeling Lamp Indicator
12. Buzz Indicator
13. Slave Triggering Indicator
14. Test Indicator Lamp
15. Light Sensor
16. Fuse
17. Wireless Control Port
18. Mounting Bracket
19. Umbrella Input
20. Direction Adjusting Handle
1. Sync Cord
2. Power Cord
3. Standard Reflector
4. Lamp Cover
5. Modeling Lamp
6. Instruction Manual
Accessories
9
- 10 -- 09 -
1 2 345

Separately Sold Accessories
The product can be used in combination with the following accessories sold
separately, so as to achieve best photography effects:
Godox FT series remote control, Power Inverter, Softbox, Photographic Umbrella,
Light Stand, Barndoor, Snoot, etc
OPERATIONS
Flash Preparation
Power Connection
1. Take down the lamp
cover. Install the modeling
lamp and put on the glass
protection cover and the
standard reflector.
(To uninstall the standard
reflector, press the release
button on the flash head
and turn the standard
reflector counter-clockwise
to take it out, as illustrated
in the picture.)
2. Attach the flash unit onto
an appropriate light stand. Adjust the mounting bracket (18) for a good angle and
make sure it is tightened and fixed. Use the direction adjusting handle (20) to
adjust the flash to a desired direction. Umbrella input (19) is for different photo
umbrellas to put in.
Use the power cord to connect the flash to an AC power source and turn on the
power switch (3). The lamp on the power switch turns on, indicating it’s connected.
Modeling Lamp Button (6) controls the modeling lamp status: when modeling
lamp indicator lights up, modeling lamp is on; if not, modeling lamp is off.
Modeling lamp output controller (4) is used for adjusting the power output level of
modeling lamp. Modeling lamp will be off automatically after lighting for 2 hours,
avoiding overheat due to long-time lighting when the user is not nearby.
Modeling Lamp
When there is flammable accessory on the flash unit, do not keep the
modeling lamp on for a long time. It is recommended to cool it down
for one minute after 10 minutes' working.
Power Output Control
Flash output controller (5) decides different power output, satisfying light
requirements in different environment. The power is adjustable freely from 5.0 to
8.0 which will be accordingly shown on the digital display (10). "OF" on the
display indicates that the flash triggering function is turned off. It can
automatically discharge power when the flash output is adjusted from high to low.
Test Button
To fire the flash without taking a picture, press the test button (9). It can also help
adjust the flash brightness when combined with the flash output controller (5).
Sync Triggering
The sync cord jack (2) is a Φ6.35mm
plug. Insert a trigger plug here and
the flash will be fired synchronously
with the camera shutter.
Slave Trigger Model
Three slave triggering models are
available and can be set by pressing Slave Model Button (8).
◆No optical control: The slave triggering indicator (13) is off, indicating the slave
triggering function is shut down.
◆One fire model: The slave triggering indicator (13) glows blue, indicating the
flash will fire synchronously when receiving one external flash. In this model, the
flash can function as an auxiliary lamp, offering various effects of light and
shadow.
◆Anti-preflash model: The slave triggering indicator (13) glows red, indicating the
flash will receive two external flashes within 2 seconds and will fire synchronously
when receiving the second flash. In this model, the flash can function as an
auxiliary lamp, applicable to TTL system. With this anti-preflash function, the flash
can synchronize with cameras having a one-preflash firing system.
Buzz Function
The sound button (7) is used for deciding whether there is sound reminder for
ready flash after recharging. When the buzz indicator (12) is on, the buzz function
is working; when it is off, the buzz function is not working. A “BI” sound will be
heard when it’s fully charged.
- 12 -- 11 -

Separately Sold Accessories
The product can be used in combination with the following accessories sold
separately, so as to achieve best photography effects:
Godox FT series remote control, Power Inverter, Softbox, Photographic Umbrella,
Light Stand, Barndoor, Snoot, etc
OPERATIONS
Flash Preparation
Power Connection
1. Take down the lamp
cover. Install the modeling
lamp and put on the glass
protection cover and the
standard reflector.
(To uninstall the standard
reflector, press the release
button on the flash head
and turn the standard
reflector counter-clockwise
to take it out, as illustrated
in the picture.)
2. Attach the flash unit onto
an appropriate light stand. Adjust the mounting bracket (18) for a good angle and
make sure it is tightened and fixed. Use the direction adjusting handle (20) to
adjust the flash to a desired direction. Umbrella input (19) is for different photo
umbrellas to put in.
Use the power cord to connect the flash to an AC power source and turn on the
power switch (3). The lamp on the power switch turns on, indicating it’s connected.
Modeling Lamp Button (6) controls the modeling lamp status: when modeling
lamp indicator lights up, modeling lamp is on; if not, modeling lamp is off.
Modeling lamp output controller (4) is used for adjusting the power output level of
modeling lamp. Modeling lamp will be off automatically after lighting for 2 hours,
avoiding overheat due to long-time lighting when the user is not nearby.
Modeling Lamp
When there is flammable accessory on the flash unit, do not keep the
modeling lamp on for a long time. It is recommended to cool it down
for one minute after 10 minutes' working.
Power Output Control
Flash output controller (5) decides different power output, satisfying light
requirements in different environment. The power is adjustable freely from 5.0 to
8.0 which will be accordingly shown on the digital display (10). "OF" on the
display indicates that the flash triggering function is turned off. It can
automatically discharge power when the flash output is adjusted from high to low.
Test Button
To fire the flash without taking a picture, press the test button (9). It can also help
adjust the flash brightness when combined with the flash output controller (5).
Sync Triggering
The sync cord jack (2) is a Φ6.35mm
plug. Insert a trigger plug here and
the flash will be fired synchronously
with the camera shutter.
Slave Trigger Model
Three slave triggering models are
available and can be set by pressing Slave Model Button (8).
◆No optical control: The slave triggering indicator (13) is off, indicating the slave
triggering function is shut down.
◆One fire model: The slave triggering indicator (13) glows blue, indicating the
flash will fire synchronously when receiving one external flash. In this model, the
flash can function as an auxiliary lamp, offering various effects of light and
shadow.
◆Anti-preflash model: The slave triggering indicator (13) glows red, indicating the
flash will receive two external flashes within 2 seconds and will fire synchronously
when receiving the second flash. In this model, the flash can function as an
auxiliary lamp, applicable to TTL system. With this anti-preflash function, the flash
can synchronize with cameras having a one-preflash firing system.
Buzz Function
The sound button (7) is used for deciding whether there is sound reminder for
ready flash after recharging. When the buzz indicator (12) is on, the buzz function
is working; when it is off, the buzz function is not working. A “BI” sound will be
heard when it’s fully charged.
- 12 -- 11 -

Memory Function
The device is equipped with memory function for the panel setting. It will help
remember the panel setting 3 seconds after you set it. When starting up the flash
next time, the panel setting will be the same as that before powering it off.
Wireless Control Function
◆The flash unit is built in with a Wireless Control Port (17) so that you can
wirelessly control the on-and-off of your flash, modeling lamp and buzzer, as well
as adjust the flash output level, etc.
◆To control the flash wirelessly, you need a Godox FT series remote control set
(on-camera and on-flash). Insert its receive end into the Wireless Control Port
(17) on the flash and insert the transmit end into the camera hot shoe. Settings
made on the hotshoe-mounted transmit and receive ends will be wirelessly
communicated to the flash. Then you can press the camera shutter-release
button to trigger the flash.
◆For full instructions on the use of FT series remote control, see its user manual.
Tube Replacement
Shut down the power and remove the power cord before replacing the flash tube.
Wear insulated gloves to loosen the iron wire on the tube, keep a balanced hold
on the two feet of the flash tube and pull out the old tube gently. Take down the
feet casing from the old tube and put it on the new one. Hold two feet of the new
tube, and target directly towards the two copper outlets, then push them slightly
in. Twine the iron wire on the stainless steel sheet to fix the flash tube.
QE400
400Ws
65
0.3~1.5s
Approx.2.8kg
QE600
600Ws
76
8A
Approx.2.84kg
QE1200
1200Ws
110
10A
Approx.3.9kg
MAINTENANCE
Shut down the device immediately when it works abnormally and find out the
reason.
Avoid sudden impacts and the lamp should be dedusted regularly.
It is normal for the lamp to be warm when in use. Avoid continuous flashes if
unnecessary.
Maintenance of the flash must be performed by our authorized maintenance
department which can provide original accessories. The flash-tube and the
modeling lamp are user-replaceable. Replacement tubes and lamps can be
obtained from the manufacturer.
This product, except consumables e.g. flash tube and modeling lamp, is
supported with a one-year warranty.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by
professional.
Disconnect the power when cleaning the flash or when changing the flashtube /
modeling lamp.
Changes made to the specifications or designs may not be reflected in this
manual.
TECHNICAL DATA
Model
Max Power (Ws)
Guide Number(m ISO 100)
Color Temperature
Operating Voltage
Power Output Control
Modeling Lamp (W)
Recycle Time
Triggering Method
Flash Duration
Fuse
Dimension
Net Weight
QE300
300Ws
58
5600±200k
AC200-240V/50Hz or AC100-120V/60Hz
OFF,5.0~8.0(1/32~1/1)
150W
0.3~1.2s
Sync cord, Test button, Slave triggering, Wireless control port
1/2000~1/800s
5A
Flash diameterΦ14cm, height of flash with handle 23cm
length of flash with lamp
cover 39cm
Approx. 2.7kg
QE800
800Ws
90
length of flash with lamp
cover 49cm
Approx.3.7kg
- 14 -- 13 -

Memory Function
The device is equipped with memory function for the panel setting. It will help
remember the panel setting 3 seconds after you set it. When starting up the flash
next time, the panel setting will be the same as that before powering it off.
Wireless Control Function
◆The flash unit is built in with a Wireless Control Port (17) so that you can
wirelessly control the on-and-off of your flash, modeling lamp and buzzer, as well
as adjust the flash output level, etc.
◆To control the flash wirelessly, you need a Godox FT series remote control set
(on-camera and on-flash). Insert its receive end into the Wireless Control Port
(17) on the flash and insert the transmit end into the camera hot shoe. Settings
made on the hotshoe-mounted transmit and receive ends will be wirelessly
communicated to the flash. Then you can press the camera shutter-release
button to trigger the flash.
◆For full instructions on the use of FT series remote control, see its user manual.
Tube Replacement
Shut down the power and remove the power cord before replacing the flash tube.
Wear insulated gloves to loosen the iron wire on the tube, keep a balanced hold
on the two feet of the flash tube and pull out the old tube gently. Take down the
feet casing from the old tube and put it on the new one. Hold two feet of the new
tube, and target directly towards the two copper outlets, then push them slightly
in. Twine the iron wire on the stainless steel sheet to fix the flash tube.
QE400
400Ws
65
0.3~1.5s
Approx.2.8kg
QE600
600Ws
76
8A
Approx.2.84kg
QE1200
1200Ws
110
10A
Approx.3.9kg
MAINTENANCE
Shut down the device immediately when it works abnormally and find out the
reason.
Avoid sudden impacts and the lamp should be dedusted regularly.
It is normal for the lamp to be warm when in use. Avoid continuous flashes if
unnecessary.
Maintenance of the flash must be performed by our authorized maintenance
department which can provide original accessories. The flash-tube and the
modeling lamp are user-replaceable. Replacement tubes and lamps can be
obtained from the manufacturer.
This product, except consumables e.g. flash tube and modeling lamp, is
supported with a one-year warranty.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by
professional.
Disconnect the power when cleaning the flash or when changing the flashtube /
modeling lamp.
Changes made to the specifications or designs may not be reflected in this
manual.
TECHNICAL DATA
Model
Max Power (Ws)
Guide Number(m ISO 100)
Color Temperature
Operating Voltage
Power Output Control
Modeling Lamp (W)
Recycle Time
Triggering Method
Flash Duration
Fuse
Dimension
Net Weight
QE300
300Ws
58
5600±200k
AC200-240V/50Hz or AC100-120V/60Hz
OFF,5.0~8.0(1/32~1/1)
150W
0.3~1.2s
Sync cord, Test button, Slave triggering, Wireless control port
1/2000~1/800s
5A
Flash diameterΦ14cm, height of flash with handle 23cm
length of flash with lamp
cover 39cm
Approx. 2.7kg
QE800
800Ws
90
length of flash with lamp
cover 49cm
Approx.3.7kg
- 14 -- 13 -

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
► -Reorient or relocate the receiving antenna.
► -Increase the separation between the equipment and receiver.
► -Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
► -Consult the dealer or an experienced radio/TV technician for help.
*RF warning:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
FCC Warning

说 明 手 册
Instruction Manual
中英文双语
Chinese English Bilingual
705-QE0000-00 Made In China
地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋
Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong
Town, Baoan District, Shenzhen 518103, China
电话/Tel: [phone](8062) 传真/Fax: [phone]
邮箱/E-mail: [email protected]
http://www.godox.com
神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
Professional Studio Flash
专 业 影 室 闪 光 灯