Godox V350F User manual

INSTRUCTION MANUAL
说 明 手 册
中英文双语 / Chinese English Bilingual
在使用本产品之前：
请先仔细阅读本手册，以确保您能安全使用。请保存好本手册以备将
来查询参考。
For FUJIFILM
Before using this product:
Please read this user manual carefully in order to ensure your safety
and the proper operation of this product. Keep for future reference.
705-V350F0-00
地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋
Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong
Town, Baoan District, Shenzhen 518103, China
电话/Tel: [phone](8062) 传真/Fax: [phone]
邮箱/E-mail: [email protected]
http://www.godox.com
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
Made In China
锂电机顶闪光灯
TTL
Pioneering Camera FlashTTL Li-ion

Thank you for purchasing this product.
This V350F camera flash applies to FUJIFILM series cameras and is
compatible with TTL autoflash. With this TTL compatible flash, your
shooting will become simpler. You can easily achieve a correct flash
exposure even in complex light-changing environments. This
camera flash features:
● GN36 (m ISO 100, @105mm).
● Pro 2000mAh Li-ion Battery –- 0.1s~1.7s recycle –- over 500 full
power pops.
● Fully support FUJIFILM TTL camera flash. Workable as Master or
Slave unit in a wireless flash group.
● With built-in 2.4GHz wireless remote system to support
transmitting and receiving.
● Provided multiple functions, include manual flash, multi flash, HSS
(up to 1/8000s), rear curtain sync, FEC, etc.
● Support with firmware upgrade.
Foreword
Always keep this product dry. Do not use in rain or in damp
conditions.
Do not disassemble. Should repairs become necessary, this
product must be sent to an authorized maintenance center.
Keep out of reach of children.
Stop using this product if it breaks open due to extrusion, falling
or strong hit. Otherwise, electric shock may occur if you touch
the electronic parts inside it.
Do not fire the flash directly into the eyes (especially those of
babies) within short distances. Otherwise visual impairment
may occur.
Do not use the flash unit in the presence of flammable gases,
chemicals and other similar materials. In certain circumstance,
these materials may be sensitive to the strong light emitting
from this flash unit and fire or electromagnetic interference may
result.
Do not leave or store the flash unit if the ambient temperature
reads over 50℃. Otherwise the electronic parts may be
damaged.
Turn off the flash unit immediately in the event of malfunction.
Warning
- 27 - - 28 -

Thank you for purchasing this product.
This V350F camera flash applies to FUJIFILM series cameras and is
compatible with TTL autoflash. With this TTL compatible flash, your
shooting will become simpler. You can easily achieve a correct flash
exposure even in complex light-changing environments. This
camera flash features:
● GN36 (m ISO 100, @105mm).
● Pro 2000mAh Li-ion Battery –- 0.1s~1.7s recycle –- over 500 full
power pops.
● Fully support FUJIFILM TTL camera flash. Workable as Master or
Slave unit in a wireless flash group.
● With built-in 2.4GHz wireless remote system to support
transmitting and receiving.
● Provided multiple functions, include manual flash, multi flash, HSS
(up to 1/8000s), rear curtain sync, FEC, etc.
● Support with firmware upgrade.
Foreword
Always keep this product dry. Do not use in rain or in damp
conditions.
Do not disassemble. Should repairs become necessary, this
product must be sent to an authorized maintenance center.
Keep out of reach of children.
Stop using this product if it breaks open due to extrusion, falling
or strong hit. Otherwise, electric shock may occur if you touch
the electronic parts inside it.
Do not fire the flash directly into the eyes (especially those of
babies) within short distances. Otherwise visual impairment
may occur.
Do not use the flash unit in the presence of flammable gases,
chemicals and other similar materials. In certain circumstance,
these materials may be sensitive to the strong light emitting
from this flash unit and fire or electromagnetic interference may
result.
Do not leave or store the flash unit if the ambient temperature
reads over 50℃. Otherwise the electronic parts may be
damaged.
Turn off the flash unit immediately in the event of malfunction.
Warning
- 27 - - 28 -

Foreword
Warning
Name of Parts
Body
Control Panel
LCD Panel
What's in the Box of V350F?
Separately Sold Accessories
Battery
Attaching to a Camera
Power Management
Flash Mode: TTL Autoflash
FEC (Flash Exposure Compensation)
High-Speed Sync
Second-Curtain Sync
Flash Mode – M: Manual Flash
Flash Mode – Multi: Stroboscopic Flash
Wireless Flash Shooting: Radio (2.4G) Transmission
Wireless Settings
Setting Master Unit’s Flash Mode
Setting the Communication Channel
Wireless ID Settings
TTL: Fully Automatic Wireless Flash Shooting
M: Wireless Flash Shooting with Manual Flash
Multi: Wireless Flash Shooting with Manual Flash
Other Applications
Auto Focus Assist Beam
Bounce Flash
Creating a Catchlight
ZOOM: Setting the Flash Coverage and Using the Wide Panel
Low Battery Indicator
C.Fn: Setting Custom Functions
Protection Function
Firmware Upgrade
Technical Data
Maintenance
Troubleshooting
Compatible Camera Models
Contents
27
28
31
33
35
35
36
38
39
40
45
47
48
49
49
50
51
52
Conventions used in this Manual
● This manual is based on the assumption that both the camera and
camera flash’s power switches are powered on.
● Reference page numbers are indicated by “p.**”.
● The following alert symbols are used in this manual:
The Caution symbol gives supplemental information.
The Note symbol indicates a warning to prevent shooting
problem.
Pioneering Li-ion Camera Flash
- 29 - - 30 -

Foreword
Warning
Name of Parts
Body
Control Panel
LCD Panel
What's in the Box of V350F?
Separately Sold Accessories
Battery
Attaching to a Camera
Power Management
Flash Mode: TTL Autoflash
FEC (Flash Exposure Compensation)
High-Speed Sync
Second-Curtain Sync
Flash Mode – M: Manual Flash
Flash Mode – Multi: Stroboscopic Flash
Wireless Flash Shooting: Radio (2.4G) Transmission
Wireless Settings
Setting Master Unit’s Flash Mode
Setting the Communication Channel
Wireless ID Settings
TTL: Fully Automatic Wireless Flash Shooting
M: Wireless Flash Shooting with Manual Flash
Multi: Wireless Flash Shooting with Manual Flash
Other Applications
Auto Focus Assist Beam
Bounce Flash
Creating a Catchlight
ZOOM: Setting the Flash Coverage and Using the Wide Panel
Low Battery Indicator
C.Fn: Setting Custom Functions
Protection Function
Firmware Upgrade
Technical Data
Maintenance
Troubleshooting
Compatible Camera Models
Contents
27
28
31
33
35
35
36
38
39
40
45
47
48
49
49
50
51
52
Conventions used in this Manual
● This manual is based on the assumption that both the camera and
camera flash’s power switches are powered on.
● Reference page numbers are indicated by “p.**”.
● The following alert symbols are used in this manual:
The Caution symbol gives supplemental information.
The Note symbol indicates a warning to prevent shooting
problem.
Pioneering Li-ion Camera Flash
- 29 - - 30 -

MODE ZOOM SYNC SLAVE
MODE ZOOM SYNC SLAVE
SET
01. Catchlight Panel
02. Built-in Wide Panel
03. Flash Head
04. Optic Control Sensor
05. Focus Assist Beam
06. Hotshoe
07. LCD Panel
08. Lock Ring
09. Battery Compartment
10. USB Port
● Body
11. <MODE>Mode Selection Button
12. <ZOOM>Zoom Selection Button
13.<SYNC>High-Speed Sync Button
14. <SLAVE> S1/S2 Optic Slave
Triggering Selection Button
(in non-wireless mode)
15. < > Power Switch
16. < > Test Button / Flash Ready
Indicator.
17. < >Custom Function Setting
Button (reusable button, long
press for 2 seconds)
18. < > Wireless Selection
Button (reusable button, long
press for 2 seconds)
19. <GR/CH> Group/Channel Button
(reusable button, in wireless
mode)
20. Select Dial
21.<SET> Set Button
● Control Panel
● LCD Panel
Name of Parts (1) TTL Autoflash
: High-speed
sync (Page 36)
02
01
03
04
05
06
09
12 13
11
16
21
20
15
14
17 18
19
Zoom : zoom display
TTL : TTL autoflash
Focus length
Flash exposure
compensation amount
(2)M Manual Flash M : Manual flash
Manual flash output
(3)Multi Flash
Multi : Stroboscopic flash
Number of flashes
Flash frequency
Flash mode
Channel
(4) Radio Transmission Shooting
● Master Unit
Firing group
● Slave Unit
Master
Slave
07
08
10
- 31 - - 32 -

MODE ZOOM SYNC SLAVE
MODE ZOOM SYNC SLAVE
SET
01. Catchlight Panel
02. Built-in Wide Panel
03. Flash Head
04. Optic Control Sensor
05. Focus Assist Beam
06. Hotshoe
07. LCD Panel
08. Lock Ring
09. Battery Compartment
10. USB Port
● Body
11. <MODE>Mode Selection Button
12. <ZOOM>Zoom Selection Button
13.<SYNC>High-Speed Sync Button
14. <SLAVE> S1/S2 Optic Slave
Triggering Selection Button
(in non-wireless mode)
15. < > Power Switch
16. < > Test Button / Flash Ready
Indicator.
17. < >Custom Function Setting
Button (reusable button, long
press for 2 seconds)
18. < > Wireless Selection
Button (reusable button, long
press for 2 seconds)
19. <GR/CH> Group/Channel Button
(reusable button, in wireless
mode)
20. Select Dial
21.<SET> Set Button
● Control Panel
● LCD Panel
Name of Parts (1) TTL Autoflash
: High-speed
sync (Page 36)
02
01
03
04
05
06
09
12 13
11
16
21
20
15
14
17 18
19
Zoom : zoom display
TTL : TTL autoflash
Focus length
Flash exposure
compensation amount
(2)M Manual Flash M : Manual flash
Manual flash output
(3)Multi Flash
Multi : Stroboscopic flash
Number of flashes
Flash frequency
Flash mode
Channel
(4) Radio Transmission Shooting
● Master Unit
Firing group
● Slave Unit
Master
Slave
07
08
10
- 31 - - 32 -

● Separately Sold Accessories
The product can be used in combination with the following
accessories sold separately, so as to achieve best photography
effects: XPro, X1T-F wireless flash trigger, Mini softbox, White &
Silver reflector, Honeycomb, Color gels, Snoot, etc.
● What’s in the Box of V350F?
1. Flash unit 2. Mini stand 3. Protection case 4. Diffuser
5. Li-ion battery pack 6. Battery charger 7. Battery charger cable
8. Instruction manual
● Features
1. This flash unit uses Li-ion polymer battery which has long runtime.
The available charge-and-discharge times are 500.
2. It is reliably safe. The inner circuit is against overcharge,
overdischarge, overcurrent, and short circuit.
3. Take only 2.5 hours to fully charge the battery by using the
standard battery charger.
● Cautions
1. Do not short circuit.
2. Do not expose to rain or immerse into water. This battery is not
water proof.
3. Keep out of reach of children.
4. No over 24 hours’continuous charging.
5. Store in dry, cool, ventilated places.
6. Do not put aside or into fire.
7. Dead batteries should be disposed according to local regulations.
8. Please charge the battery to approx. 60% before being placed for
long time.
9. If the battery had ceased using for over 3 months, please make a
full recharge.
● Loading and Unloading the Battery
Battery
To load the battery, push the
1battery compartment cover
downward and open it, and
the battery pack will pop out.
To load the battery, according
2to the triangle sign on the
battery pack, insert it into the
compartment until it is locked.
Then close the compartment.
● Battery Level Indication
Make sure the battery pack is securely loaded in the flash. Check
the battery level indication on the LCD panel to see the remaining
battery level.
Battery Level Indication
2 grids
1 grid
Blank grid
Blinking The battery level is going to be used out
immediately. And the flash will auto power off
in 1 minute.
Note: Please recharge the battery as soon as
possible (within 10 days). Then, the battery can be
used or be placed for long period.
Meaning
Full
Middle
Low
- 33 - - 34 -

● Separately Sold Accessories
The product can be used in combination with the following
accessories sold separately, so as to achieve best photography
effects: XPro, X1T-F wireless flash trigger, Mini softbox, White &
Silver reflector, Honeycomb, Color gels, Snoot, etc.
● What’s in the Box of V350F?
1. Flash unit 2. Mini stand 3. Protection case 4. Diffuser
5. Li-ion battery pack 6. Battery charger 7. Battery charger cable
8. Instruction manual
● Features
1. This flash unit uses Li-ion polymer battery which has long runtime.
The available charge-and-discharge times are 500.
2. It is reliably safe. The inner circuit is against overcharge,
overdischarge, overcurrent, and short circuit.
3. Take only 2.5 hours to fully charge the battery by using the
standard battery charger.
● Cautions
1. Do not short circuit.
2. Do not expose to rain or immerse into water. This battery is not
water proof.
3. Keep out of reach of children.
4. No over 24 hours’continuous charging.
5. Store in dry, cool, ventilated places.
6. Do not put aside or into fire.
7. Dead batteries should be disposed according to local regulations.
8. Please charge the battery to approx. 60% before being placed for
long time.
9. If the battery had ceased using for over 3 months, please make a
full recharge.
● Loading and Unloading the Battery
Battery
To load the battery, push the
1battery compartment cover
downward and open it, and
the battery pack will pop out.
To load the battery, according
2to the triangle sign on the
battery pack, insert it into the
compartment until it is locked.
Then close the compartment.
● Battery Level Indication
Make sure the battery pack is securely loaded in the flash. Check
the battery level indication on the LCD panel to see the remaining
battery level.
Battery Level Indication
2 grids
1 grid
Blank grid
Blinking The battery level is going to be used out
immediately. And the flash will auto power off
in 1 minute.
Note: Please recharge the battery as soon as
possible (within 10 days). Then, the battery can be
used or be placed for long period.
Meaning
Full
Middle
Low
- 33 - - 34 -

C.Fn
Attaching to a Camera
Attach the Camera Flash.
1● Slip the camera flash’s
mounting foot into the
camera’s hotshoe all the
way.
Secure the Camera Flash.
2● Rotate the lock ring on the
mounting foot until it locks
up.
Detach the Camera Flash.
3● Rotate the lock ring on the
mounting foot until it is
loosened.
Power Management
Use Power Switch to power the flash unit on (Long press the
button for one second) or off. Turn off if it will not be used for an
extended period of time. Setting as a master flash, it will turn the
power off automatically after a certain period (approx. 90 seconds)
of idle use. Pressing the camera shutter halfway or pressing any
flash button will wake up the flash unit. Setting as a slave flash, it
will enter sleep mode after a certain period (adjustable, 60 minutes
by default) of idle use. Pressing any flash button will wake it up.
Disabling Auto Power Off function is recommended
when the flash is used off camera. (C.Fn-ST, Page 47)
Flash Mode: TTL Autoflash
This flash has three flash modes: TTL, Manual (M), and Multi
(Stroboscopic). In TTL mode, the camera and the flash will work
together to calculate the correct exposure for the subject and the
background. In this mode, multiple TTL functions are available:
FEC, HSS, second curtain sync, etc.
* Press <MODE> Mode Selection Button and three flash modes will
display on the LCD panel one by one with each pressing.
TTL Mode
Press <MODE> Mode Selection Button to enter TTL mode. The
LCD panel will display <TTL>.
● Press the camera release button halfway to focus.
● When the shutter button is fully pressed, the flash will fire a pre-
flash that the camera will use to calculate exposure and flash
output the instant before the photo is taken.
Display“HI”: When the flash output value is up to the maximum
value, “HI”will be displayed and blinking for 3 seconds. Adjust
the camera’s parameters if underexposure appears.
Display“Lo”: When the flash output value is up to the minimum
value, “Lo”will be displayed and blinking for 3 seconds. Adjust the
camera’s parameters if overexposure appears.
- 35 - - 36 -
FEC: Flash Exposure Compensation
With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops.
It is useful in situations where minor adjusting of the TTL system is
needed based on the environment.
Setting FEC:
Turn the Select Dial to set the
2amount.
● “0.3”means 1/3 step,
“0.7”means 2/3 step.
● To cancel the flash
exposure compensation,
set the amount to “+0”.
Press < SET > button again
3to confirm the setting.
Press the SET Button and
1the flash exposure
compensation amount will be
highlighted on the LCD panel.
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET

C.Fn
Attaching to a Camera
Attach the Camera Flash.
1● Slip the camera flash’s
mounting foot into the
camera’s hotshoe all the
way.
Secure the Camera Flash.
2● Rotate the lock ring on the
mounting foot until it locks
up.
Detach the Camera Flash.
3● Rotate the lock ring on the
mounting foot until it is
loosened.
Power Management
Use Power Switch to power the flash unit on (Long press the
button for one second) or off. Turn off if it will not be used for an
extended period of time. Setting as a master flash, it will turn the
power off automatically after a certain period (approx. 90 seconds)
of idle use. Pressing the camera shutter halfway or pressing any
flash button will wake up the flash unit. Setting as a slave flash, it
will enter sleep mode after a certain period (adjustable, 60 minutes
by default) of idle use. Pressing any flash button will wake it up.
Disabling Auto Power Off function is recommended
when the flash is used off camera. (C.Fn-ST, Page 47)
Flash Mode: TTL Autoflash
This flash has three flash modes: TTL, Manual (M), and Multi
(Stroboscopic). In TTL mode, the camera and the flash will work
together to calculate the correct exposure for the subject and the
background. In this mode, multiple TTL functions are available:
FEC, HSS, second curtain sync, etc.
* Press <MODE> Mode Selection Button and three flash modes will
display on the LCD panel one by one with each pressing.
TTL Mode
Press <MODE> Mode Selection Button to enter TTL mode. The
LCD panel will display <TTL>.
● Press the camera release button halfway to focus.
● When the shutter button is fully pressed, the flash will fire a pre-
flash that the camera will use to calculate exposure and flash
output the instant before the photo is taken.
Display“HI”: When the flash output value is up to the maximum
value, “HI”will be displayed and blinking for 3 seconds. Adjust
the camera’s parameters if underexposure appears.
Display“Lo”: When the flash output value is up to the minimum
value, “Lo”will be displayed and blinking for 3 seconds. Adjust the
camera’s parameters if overexposure appears.
- 35 - - 36 -
FEC: Flash Exposure Compensation
With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops.
It is useful in situations where minor adjusting of the TTL system is
needed based on the environment.
Setting FEC:
Turn the Select Dial to set the
2amount.
● “0.3”means 1/3 step,
“0.7”means 2/3 step.
● To cancel the flash
exposure compensation,
set the amount to “+0”.
Press < SET > button again
3to confirm the setting.
Press the SET Button and
1the flash exposure
compensation amount will be
highlighted on the LCD panel.
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET

The flash output is adjustable from 1/1 full power to 1/128th power
in 1/3rd stop increments. To obtain a correct flash exposure, use a
hand-held flash meter to determine the required flash output.
Flash Mode – M: Manual Flash
Press < MODE > button so
1that < M > is displayed.
Turn the Select Dial to choose
2a desired flash output amount.
In high-speed sync mode,
the adjustable flash range is
1/16~1/1.
Figures displayed when reducing flash output level
Figures displayed when increasing flash output level
1/41/21/1
1/1-0.3
1/2+0.7
1/1-0.7
1/2+0.3
1/2-0.3
1/4+0.7
1/2-0.7
1/4+0.3
······
······
Flash Output Range
The following table makes it easier to see how the stop changes in
terms of f/stop when you increase or decrease the flash output. For
example, when you decrease the flash output to 1/2, 1/2-0.3, or 1/2-
0.7, and then increase the flash output to more than 1/2, 1/2+0.3,
1/2+0.7, and 1/1 will be displayed.
Optical S1 Secondary Unit Setting
In M manual flash mode, press the <SLAVE> button so that this
flash can function as an optic S1 secondary flash with optic sensor.
With this function, the flash will fire synchronously when the main
flash fires, the same effect as that by the use of radio triggers. This
helps create multiple lighting effects.
Optical S2 Secondary Unit Setting
Press the <SLAVE> button so that this flash can also function as an
optic S2 secondary flash with optic sensor in M manual flash mode.
This is useful when cameras have pre-flash function. With this
function, the flash will ignore a single “preflash” from the main flash
and will only fire in response to the second, actual flash from the
main unit.
● S1 and S2 optic triggering and off camera high-speed
mode are only available in M manual flash mode.
In the M mode, high-speed sync and rear curtain sync functions
can be achieved.
- 37 - - 38 -
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
High-Speed Sync
High Speed Sync (Hss flash) enables the flash to synchronize with
all camera shutter speeds. This is convenient when you want to use
aperture priority for fill-flash portraits.
● Setting the flash to High-speed Sync mode when it is on the camera:
Use the Flash Setting ＞ Flash Light Function Setting on the
camera’s shooting menu to adjust settings of the flash light. More
details please refer to camera’s instruction menu.
● When choosing FP on the “SYNC” setting, it means the
high-speed sync function is turned on.
SYNC.MODE
TTL ±0
-5.0+5.0
TTL MODE TTL
ZOOM M 16mm
LED AF
SYNC.
ANGLE
FP
BACK
ADJUST END
SHOE MOUNT FLASH
Press the <SYNC> button to open the high-speed sync flash and
high-speed icon <> is displayed.
● Setting “Sync cord jack/S1/S2”high-speed sync flash:
Choose Sync cord jack/S1/S2 triggering method to achieve high-speed
sync flash.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following the
subject. The flash fires right before the shutter closes.
● Setting second-curtain sync:
Use the Flash Setting ＞Flash Light Function Setting on the
camera’s shooting menu to adjust settings of the flash light. More
details please refer to camera’s instruction menu.
● When choosing REAR on the “SYNC” setting, it means the
second-curtain sync function is turned on.
● With high-speed sync, the faster the shutter speed, the
shorter the effective flash range.
● Multi flash mode cannot be set in high-speed sync mode.
● Over-temperature protection may be activated after 15
consecutive high-speed sync flashes.
● Try to avoid using high-speed sync flash, which will cut
short flash tube’s lifetime.
SYNC.MODE
TTL ±0
-5.0+5.0
TTL MODE TTL
ZOOM M 16mm
LED AF
SYNC.
ANGLE
REAR
BACK
ADJUST END
SHOE MOUNT FLASH

The flash output is adjustable from 1/1 full power to 1/128th power
in 1/3rd stop increments. To obtain a correct flash exposure, use a
hand-held flash meter to determine the required flash output.
Flash Mode – M: Manual Flash
Press < MODE > button so
1that < M > is displayed.
Turn the Select Dial to choose
2a desired flash output amount.
In high-speed sync mode,
the adjustable flash range is
1/16~1/1.
Figures displayed when reducing flash output level
Figures displayed when increasing flash output level
1/41/21/1
1/1-0.3
1/2+0.7
1/1-0.7
1/2+0.3
1/2-0.3
1/4+0.7
1/2-0.7
1/4+0.3
······
······
Flash Output Range
The following table makes it easier to see how the stop changes in
terms of f/stop when you increase or decrease the flash output. For
example, when you decrease the flash output to 1/2, 1/2-0.3, or 1/2-
0.7, and then increase the flash output to more than 1/2, 1/2+0.3,
1/2+0.7, and 1/1 will be displayed.
Optical S1 Secondary Unit Setting
In M manual flash mode, press the <SLAVE> button so that this
flash can function as an optic S1 secondary flash with optic sensor.
With this function, the flash will fire synchronously when the main
flash fires, the same effect as that by the use of radio triggers. This
helps create multiple lighting effects.
Optical S2 Secondary Unit Setting
Press the <SLAVE> button so that this flash can also function as an
optic S2 secondary flash with optic sensor in M manual flash mode.
This is useful when cameras have pre-flash function. With this
function, the flash will ignore a single “preflash” from the main flash
and will only fire in response to the second, actual flash from the
main unit.
● S1 and S2 optic triggering and off camera high-speed
mode are only available in M manual flash mode.
In the M mode, high-speed sync and rear curtain sync functions
can be achieved.
- 37 - - 38 -
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
High-Speed Sync
High Speed Sync (Hss flash) enables the flash to synchronize with
all camera shutter speeds. This is convenient when you want to use
aperture priority for fill-flash portraits.
● Setting the flash to High-speed Sync mode when it is on the camera:
Use the Flash Setting ＞ Flash Light Function Setting on the
camera’s shooting menu to adjust settings of the flash light. More
details please refer to camera’s instruction menu.
● When choosing FP on the “SYNC” setting, it means the
high-speed sync function is turned on.
SYNC.MODE
TTL ±0
-5.0+5.0
TTL MODE TTL
ZOOM M 16mm
LED AF
SYNC.
ANGLE
FP
BACK
ADJUST END
SHOE MOUNT FLASH
Press the <SYNC> button to open the high-speed sync flash and
high-speed icon <> is displayed.
● Setting “Sync cord jack/S1/S2”high-speed sync flash:
Choose Sync cord jack/S1/S2 triggering method to achieve high-speed
sync flash.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following the
subject. The flash fires right before the shutter closes.
● Setting second-curtain sync:
Use the Flash Setting ＞Flash Light Function Setting on the
camera’s shooting menu to adjust settings of the flash light. More
details please refer to camera’s instruction menu.
● When choosing REAR on the “SYNC” setting, it means the
second-curtain sync function is turned on.
● With high-speed sync, the faster the shutter speed, the
shorter the effective flash range.
● Multi flash mode cannot be set in high-speed sync mode.
● Over-temperature protection may be activated after 15
consecutive high-speed sync flashes.
● Try to avoid using high-speed sync flash, which will cut
short flash tube’s lifetime.
SYNC.MODE
TTL ±0
-5.0+5.0
TTL MODE TTL
ZOOM M 16mm
LED AF
SYNC.
ANGLE
REAR
BACK
ADJUST END
SHOE MOUNT FLASH

SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
Set the flash frequency and
3flash times.
● Press the SET Button to
select the flash frequency.
Turn the Select Dial to set
the number.
● Press the SET Button
again to select the flash
times. Turn the Select Dial
to set the number.
Flash Mode – Multi: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be
used to capture a multiple images of a moving subject in a single
photograph.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes, and the flash output.
Press <MODE> button so
1that <Multi> is displayed.
Turn the Select Dial to choose
2a desired flash output.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
For example, if the number of flashes is 10 and the firing frequency is
5 Hz, the shutter speed should be at least 2 seconds.
Number of Flashes / Flash Frequency = Shutter Speed
To avoid overheating and deteriorating the flash head, do not
use stroboscopic flash more than 10 times in succession.
After 10 times, allow the camera flash to rest for at least 15
minutes. If you try to use the stroboscopic flash more than 10
times in succession, the firing might stop automatically to
protect the flash head. If this happens, allow at least 15
minutes’ rest for the camera flash.
● Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
● Using a tripod and a remote control is recommended.
● Stroboscopic flash can be used with“buLb”.
● If the number of flashes is displayed as “--”, the firing will
continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown
by the following table.
Maximum Stroboscopic Flashes:
1/4
1/8
1/16
1/32
1/64
1/128
1
6
14
30
60
90
90
2
3
14
30
60
90
90
3
2
6
30
60
90
90
4
2
4
20
50
80
90
5
2
3
10
50
80
90
6-7
2
3
8
40
70
90
8-9
2
3
5
12
60
80
2
2
3
5
20
70
2
2
3
5
10
30
Hz 60-90
20-50
2
2
3
5
10
20
Flash
output
Wireless Flash Shooting: Radio (2.4G) Transmission
● You can set up three slave groups for TTL autoflash shooting.
With TTL autoflash, you can easily create various lighting effects.
● Any flash settings for the slave units on the master flash in TTL
mode will be automatically sent to the slave units. So the only
thing you need to do is to set the master unit for each slave group
without any operation for the slave units at all during the shooting.
● This flash can work in TTL /M /Multi / OFF flash modes when set
as a master unit.
Master Unit Setting
1. Wireless Settings
You can switch between normal flash and wireless flash. For normal
flash shooting, be sure to set the wireless setting to OFF.
Long Press the <SYNC>
1button for 2 seconds so that
< > is blinking. Turn the
Select Dial until the < >
is displayed on the LCD
panel, which means the
master unit.
● Even with multiple slave units, the master unit can control
all of them via wireless.
● In this user manual, “master unit” refers to the camera flash
on a camera and “slave unit” will be controlled by the
master unit.
When using Godox 2.4G wireless X system, V350F is perfectly
compatible with other products of our company.
As a master unit, V350F can control the following slave unit
models: AD600, AD600M, AD360II-C, AD360II-N, V860IIF, V850II,
TT685F, TT600.
As a slave unit, V350F can be controlled by the following master
unit models: XProF, X1T-F, V860IIF, V850II, TT685F, TT600.
- 39 - - 40 -
10-19

SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
Set the flash frequency and
3flash times.
● Press the SET Button to
select the flash frequency.
Turn the Select Dial to set
the number.
● Press the SET Button
again to select the flash
times. Turn the Select Dial
to set the number.
Flash Mode – Multi: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be
used to capture a multiple images of a moving subject in a single
photograph.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes, and the flash output.
Press <MODE> button so
1that <Multi> is displayed.
Turn the Select Dial to choose
2a desired flash output.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
For example, if the number of flashes is 10 and the firing frequency is
5 Hz, the shutter speed should be at least 2 seconds.
Number of Flashes / Flash Frequency = Shutter Speed
To avoid overheating and deteriorating the flash head, do not
use stroboscopic flash more than 10 times in succession.
After 10 times, allow the camera flash to rest for at least 15
minutes. If you try to use the stroboscopic flash more than 10
times in succession, the firing might stop automatically to
protect the flash head. If this happens, allow at least 15
minutes’ rest for the camera flash.
● Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
● Using a tripod and a remote control is recommended.
● Stroboscopic flash can be used with“buLb”.
● If the number of flashes is displayed as “--”, the firing will
continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown
by the following table.
Maximum Stroboscopic Flashes:
1/4
1/8
1/16
1/32
1/64
1/128
1
6
14
30
60
90
90
2
3
14
30
60
90
90
3
2
6
30
60
90
90
4
2
4
20
50
80
90
5
2
3
10
50
80
90
6-7
2
3
8
40
70
90
8-9
2
3
5
12
60
80
2
2
3
5
20
70
2
2
3
5
10
30
Hz 60-90
20-50
2
2
3
5
10
20
Flash
output
Wireless Flash Shooting: Radio (2.4G) Transmission
● You can set up three slave groups for TTL autoflash shooting.
With TTL autoflash, you can easily create various lighting effects.
● Any flash settings for the slave units on the master flash in TTL
mode will be automatically sent to the slave units. So the only
thing you need to do is to set the master unit for each slave group
without any operation for the slave units at all during the shooting.
● This flash can work in TTL /M /Multi / OFF flash modes when set
as a master unit.
Master Unit Setting
1. Wireless Settings
You can switch between normal flash and wireless flash. For normal
flash shooting, be sure to set the wireless setting to OFF.
Long Press the <SYNC>
1button for 2 seconds so that
< > is blinking. Turn the
Select Dial until the < >
is displayed on the LCD
panel, which means the
master unit.
● Even with multiple slave units, the master unit can control
all of them via wireless.
● In this user manual, “master unit” refers to the camera flash
on a camera and “slave unit” will be controlled by the
master unit.
When using Godox 2.4G wireless X system, V350F is perfectly
compatible with other products of our company.
As a master unit, V350F can control the following slave unit
models: AD600, AD600M, AD360II-C, AD360II-N, V860IIF, V850II,
TT685F, TT600.
As a slave unit, V350F can be controlled by the following master
unit models: XProF, X1T-F, V860IIF, V850II, TT685F, TT600.
- 39 - - 40 -
10-19

MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
Long Press the <SYNC>
1button for 2 seconds so that
< > is blinking. Turn the
Select Dial until the < > is
displayed on the LCD panel,
which means the slave unit.
Slave Unit Setting
Press the <SLAVE> Button to
1ch oos e th e gro up fro m
M/A/B/C. Then, press the
< MODE > Button so that the
master unit can work in OFF /
TTL / M flash mode. Choose
one of them as the flash
mode of master unit.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Long press the <SLAVE>
1Button for 2 seconds until the
channel IDs is blinking. Turn
the Select Dial to choose a
channel ID from 1 to 16.
Press the <SET> button to
2confirm.
2. Setting Master Unit’s Flash Mode
Press the <MODE> Button for
22 seconds to switch to Multi
mode.
Slave Unit Setting
2● Set the V350F that to be
controlled as the wireless
slave unit. (Page 41)
● The slave unit can be set
as A/B/C.
Check the communication
3channel
● If the master unit and
slave unit(s) are set to a
different channel, set them
to the same channel.
(Page 41)
Position the camera and
4flashes
● Position the camera and
flashes as the picture
shows. (Page 43)
Check the flash operation
5● Press the master unit’s
Test Button< >.
● Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
The slave unit might be out of order or fire an unwanted flash
due to the nearby wifi routers or other 2.4G equipments. If in
this case, please adjust the flash’s channel or turn off the 2.4G
equipments.
Autoflash Shooting with One Slave Unit
5. TTL: Fully Automatic Wireless Flash Shooting
Master Unit Setting
1● Attach a V350F camera
flash on the camera and set it
as the master unit. (Page 40)
● M/A/B/C can be set as
TTL mode independently.
- 41 - - 42 -
4. Wireless ID Settings
Change the wireless channels and wireless ID to avoid interference
for it can only be triggered after the wireless IDs and channels of the
master unit and the slave unit are set to the same.
Press the <MENU> button to enter C.Fn ID. Press the <SET> button
to choose OFF channel expansion shutdown, and choose any figure
from 01 to 99.
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the flash mode to
1<M>
● Press the <MODE> Button
to set the flash to M mode.
Setting flash output
2● Turn the Select Dial to set
the flash output of the
groups.

MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
Long Press the <SYNC>
1button for 2 seconds so that
< > is blinking. Turn the
Select Dial until the < > is
displayed on the LCD panel,
which means the slave unit.
Slave Unit Setting
Press the <SLAVE> Button to
1ch oos e th e gro up fro m
M/A/B/C. Then, press the
< MODE > Button so that the
master unit can work in OFF /
TTL / M flash mode. Choose
one of them as the flash
mode of master unit.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Long press the <SLAVE>
1Button for 2 seconds until the
channel IDs is blinking. Turn
the Select Dial to choose a
channel ID from 1 to 16.
Press the <SET> button to
2confirm.
2. Setting Master Unit’s Flash Mode
Press the <MODE> Button for
22 seconds to switch to Multi
mode.
Slave Unit Setting
2● Set the V350F that to be
controlled as the wireless
slave unit. (Page 41)
● The slave unit can be set
as A/B/C.
Check the communication
3channel
● If the master unit and
slave unit(s) are set to a
different channel, set them
to the same channel.
(Page 41)
Position the camera and
4flashes
● Position the camera and
flashes as the picture
shows. (Page 43)
Check the flash operation
5● Press the master unit’s
Test Button< >.
● Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
The slave unit might be out of order or fire an unwanted flash
due to the nearby wifi routers or other 2.4G equipments. If in
this case, please adjust the flash’s channel or turn off the 2.4G
equipments.
Autoflash Shooting with One Slave Unit
5. TTL: Fully Automatic Wireless Flash Shooting
Master Unit Setting
1● Attach a V350F camera
flash on the camera and set it
as the master unit. (Page 40)
● M/A/B/C can be set as
TTL mode independently.
- 41 - - 42 -
4. Wireless ID Settings
Change the wireless channels and wireless ID to avoid interference
for it can only be triggered after the wireless IDs and channels of the
master unit and the slave unit are set to the same.
Press the <MENU> button to enter C.Fn ID. Press the <SET> button
to choose OFF channel expansion shutdown, and choose any figure
from 01 to 99.
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the flash mode to
1<M>
● Press the <MODE> Button
to set the flash to M mode.
Setting flash output
2● Turn the Select Dial to set
the flash output of the
groups.

SET
MODE ZOOM SYNC SLAVE
SET
Setting <Multi>
1stroboscopic flash.
● Long press the <MODE>
button for 2 seconds so that
<Multi> is displayed. Long
press the <MODE> button
for 2 seconds again to exit.
Using a flash (master/slave) with a radio transmission wireless
shooting function make it easy to shoot with advanced wireless
multiple flash lighting, in the same way as TTL autoflash shooting.
The basic relative position and operation range are as shown in the
picture. You can then perform wireless TTL autoflash shooting just
by setting the master unit to <TTL>.
7. Multi: Wireless Flash Shooting with Manual
Flash
Setting flash output/flash
2frequency/flash times.
● Setting the flash
output/flash frequency/flash
times of the groups in the M
mode. Setting the multi flash
mode. (see Page39)
● A, B and C group can only
control the ON/OFF of the
slave unit by pressing the
<MODE> Button.
Transmission distance is about 30m.
● Use the supplied mini stand to position the slave unit.
● Before shooting, perform a test flash and test shooting.
● The transmission distance might be shorter depending on
the conditions such as positioning of slave units, the
surrounding environment and whether conditions.
You can divide the slave units into two or three groups and perform
TTL autoflash while changing the flash ratio (factor). In addition, you
can set and shoot with a different flash mode for each firing group,
for up to 3 groups.
Wireless Multiple Flash Shooting
● Auto Shooting with Two Slave Groups
Slave/Master Unit's Positioning and Operation Range
● Autoflash Shooting with One Slave Unit
A
B
A
B
C
● Auto Shooting with Three Slave Groups
- 43 - - 44 -
Taking the picture
3● Each group fires at the set
flash ratio.
1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base
station, 2.4G wifi router, Bluetooth, etc.)
→ To adjust the channel CH setting on the flash trigger (add 10+ channels) and
use the channel which is not disturbed. Or turn off the other 2.4G equipment
in working.
2. Please make sure that whether the flash has finished its recycle or
caught up with the continuous shooting speed or not(the flash ready
indicator is lighten) and the flash is not under the state of over-heat
protection or other abnormal situation.
→Please downgrade the flash power output. If the flash is in TTL mode, please
try to change it to M mode(a preflash is needed in TTL mode).
The Reason & Solution of Not Triggering in Godox 2.4G Wireless

SET
MODE ZOOM SYNC SLAVE
SET
Setting <Multi>
1stroboscopic flash.
● Long press the <MODE>
button for 2 seconds so that
<Multi> is displayed. Long
press the <MODE> button
for 2 seconds again to exit.
Using a flash (master/slave) with a radio transmission wireless
shooting function make it easy to shoot with advanced wireless
multiple flash lighting, in the same way as TTL autoflash shooting.
The basic relative position and operation range are as shown in the
picture. You can then perform wireless TTL autoflash shooting just
by setting the master unit to <TTL>.
7. Multi: Wireless Flash Shooting with Manual
Flash
Setting flash output/flash
2frequency/flash times.
● Setting the flash
output/flash frequency/flash
times of the groups in the M
mode. Setting the multi flash
mode. (see Page39)
● A, B and C group can only
control the ON/OFF of the
slave unit by pressing the
<MODE> Button.
Transmission distance is about 30m.
● Use the supplied mini stand to position the slave unit.
● Before shooting, perform a test flash and test shooting.
● The transmission distance might be shorter depending on
the conditions such as positioning of slave units, the
surrounding environment and whether conditions.
You can divide the slave units into two or three groups and perform
TTL autoflash while changing the flash ratio (factor). In addition, you
can set and shoot with a different flash mode for each firing group,
for up to 3 groups.
Wireless Multiple Flash Shooting
● Auto Shooting with Two Slave Groups
Slave/Master Unit's Positioning and Operation Range
● Autoflash Shooting with One Slave Unit
A
B
A
B
C
● Auto Shooting with Three Slave Groups
- 43 - - 44 -
Taking the picture
3● Each group fires at the set
flash ratio.
1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base
station, 2.4G wifi router, Bluetooth, etc.)
→ To adjust the channel CH setting on the flash trigger (add 10+ channels) and
use the channel which is not disturbed. Or turn off the other 2.4G equipment
in working.
2. Please make sure that whether the flash has finished its recycle or
caught up with the continuous shooting speed or not(the flash ready
indicator is lighten) and the flash is not under the state of over-heat
protection or other abnormal situation.
→Please downgrade the flash power output. If the flash is in TTL mode, please
try to change it to M mode(a preflash is needed in TTL mode).
The Reason & Solution of Not Triggering in Godox 2.4G Wireless

MODE ZOOM SYNC SLAVE
SET
Other Applications
● When not attaching to the camera, the auto focus assist
beam of V350F does not light up.
● When attaching to the camera, the auto focus assist beam
of TT350F can only be lighted by setting its focus mode
(M/C/S) to S mode. The other two modes cannot light up its
auto focus assist beam.
Position
Center
Periphery
Effective Range
0.6~4m
0.6~2.5m
Bounce Flash
By pointing the flash head toward a wall or ceiling, the flash will
bounce off the surface before illuminating the subject. This can
soften shadows behind the subject for a more natural-looking shot.
This is called bounce flash.
To set the bounce direction, hold the flash head and turn it to a
satisfying angle.
● If the wall or ceiling is too far away, the bounced flash might
be too weak and result in underexposure.
● The wall or ceiling should be a plain, white color for high
reflectance. If the bounce surface is not white, a color cast
may appear in the picture.
Creating a Catchlight
With the catchlight panel, you can create a catchlight in the subject’s
eyes to add life to the facial expression.
Point the flash head upward by
190°.
Pull out the wide panel. The
2catchlight panel will come out
at the same time.
Push the wide panel back in.
3
● Push in only the wide panel.
● Follow the same procedures
as for bounce flash.
● Point the flash head straight ahead and then upward by 90°.
The catchlight will not appear if you swing the flash head left
or right.
● For best catchlight effect, stay 1.5m/4.9ft away from the
subject.
ZOOM: Setting the Flash Coverage and Using
the Wide Panel
The flash coverage can be set automatically or manually. It can be
set to match the lens focal length from 24-105mm(135 format)/16-
56mm(APS). Also, with the built-in wide panel, the flash coverage
can be expanded for 14mm wide-angle lenses.
In Manual Zoom mode, press the
<ZOOM> button.
● Turn the Select Dial to change
the flash coverage.
● AUIf < > is displayed, the flash
coverage will be set
automatically.
● If you set the flash coverage manually, make sure it covers
the lens focal length so that the picture will not have a dark
periphery.
● When the low battery indicator is displayed, the ZOOM can
not be adjusted, it will constantly be 16mm.
● Choose 135 format or APS in the C.Fn-AP.
- 45 - - 46 -
3. Whether the distance between the flash trigger and the flash
is too close or not
→Please turn on the “close distance wireless mode” on the flash trigger
(＜0.5m):
X1 series: press the test button and hold on, then turning it on until the flash
ready indicator blinks for 2 times.
XPro series: Set the C.Fn-DIST to 0-30m.
4. Whether the flash trigger and the receiver end equipment are in the low
battery states or not
→Please replace the battery(the flash trigger is recommended to use 1.5V
disposable alkaline battery).
270
-7-90
Auto Focus Assist Beam
Long press the C.Fn to enter C.Fn custom settings and press SET
button: choose “ON” or “OFF” to turn on or off the to the AF-assist
beam function . When turning on the AF-assist beam function: the
red AF-assist lamp will light when it’s hard to focus while
automatically off when getting correct focus.