Goldair GHV40 User manual

2-in-1 Duo Stick Vacuum
Model GHV40
OPERATING INSTRUCTIONS
GHV40: 9.6V DC 85W, 2-in-1 Vacuum

Thank you for choosing this Goldair 2-in-1 Stick Vacuum. This Goldair appliance has
been designed and manufactured to high standards of engineering, and with proper use
and care, as described in this manual, will provide you with years of useful service.
Please read these instructions carefully.
GENERAL CARE AND SAFETY GUIDE
ALWAYS
✔Always ensure hands are dry before
handling the plug or the Vacuum .
✔Use only as described in this manual.
✔Always be sure to unplug from the
socket when not in use and before
cleaning.
✔Use only manufacturers recommended
attachments.
✔Carry out regular checks of the supply
cord to ensure no damage is evident.
NEVER
✘Leave vacuum cleaner when plugged
in. Unplug from outlet when not in use and
before servicing.
✘Never use outdoors or on wet surfaces.
✘Never use this appliance for any
purpose other than its intended use. This
appliance is for household use only.
✘This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge, unless they are supervised or
have been given instruction concerning
the use of the vacuum by a person
responsible for their safety.
✘Close supervision is necessary when
the appliance is near children.
✘Use you vacuum to pick up anything
that is burning or smoking, such as
cigarettes, matches, or hot ashes.
✘Pull or carry by cord, use cord as a
handle, close door on cord, or pull cord
around sharp edges or corners. Do not run
vacuum cleaner over cord. Keep cord
away from heated surfaces.
✘Unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
✘Never use harsh, abrasive or caustic
cleaners to clean this appliance.
✘Never operate the appliance with a
damaged cord or plug, after it
malfunctions, or if it has been damaged in
any manner.
✘Use without dust bag and/or filter in
place.
SAVE THESE INSTRUCTIONS

GENERAL CARE AND SAFETY GUIDE continued…
•Check that your local mains voltage matches the voltage of the mains adaptor
provided with this appliance.
•This product includes rechargeable nickel metal hydride (Ni-MH) batteries.
Batteries must be recycled or disposed of properly. Do not incinerate batteries or
expose to high temperatures, as they may explode.
•Leaks from battery cells can occur under extreme conditions. If the liquid gets on
the skin, wash immediately with soap and water or neutralise with a mild acid such
as lemon juice or vinegar. If the liquid gets into the eyes, flush them immediately
with clean water for a minimum of ten minutes and seek medical attention.
•Batteries should be removed if the appliance is not going to be used for a long
period of time.
•DO NOT attempt to change the batteries used in this product yourself. The
batteries should only be replaced by a reputable service technician.
COMPONENTS
1A. Stick Power Switch
1B. Hand Vac Power Switch
2. Upper Handle
3. Folding Axis Release
4. Release Hand Vac Release Button
5. Stick Vac Body
6. Filter Assembly
7. Hand Vac Unit
8. Motorised Turbo Brush Head
9. Charging Base
10. Charger Cord and Plug
11. Turbo Brush Assembly

CHARGING THE STICK VAC
1. Ensure that the On/Off switch is in the “O” position before charging.
2. Before using the vacuum, charge the unit for 8-10 hours.
3. Plug the charger jack into the charging base.
4. Plug the charger directly into a wall outlet, ensuring the charger station is close to
the outlet.
5. Place the unit onto the charging base. A blue charging light indicates that the
vacuum is properly positioned and that the unit is being charged.
6. Store the vacuum in the charging base when not in use so that it is always charged
and ready to use.
NOTE:
•Peak performance may only be realised after the unit has been charged and
discharged two or three times. To maintain peak performance of your vacuum, it is
recommended that the unit be fully discharged then completely recharged at least
once a month. Each recharge will take approximately 12-16 hours’ charging time.
•The adaptor may become warm during charging –this is normal.
USING THE STICK VAC
NOTE:
•The Stick Vac can only be used when the Hand Vac is attached.
•The Stick Vac and Hand Vac has one power setting only.
1. Remove the appliance from the charging base.
2. Slide the “On/Off” button to the “I”position.
3. When finished vacuuming, slide the “On/Off” button to the “O” position.
ASSEMBLY
NOTE: The dust cup filter must always be used when operating the vacuum.
1. Before assembling this appliance, ensure that all parts are in the box.
2. Attach the handle by inserting into the main vacuum unit and ensure a clicking
sound secures the vacuum into place.
3. Attach the turbo brush head by inserting into the air intake nozzle at the bottom of
the Stick Vac, ensuring that the contact pins are engaged in the connector slots in
the unit. The head is successfully attached when clicked into place.
4. Attach the Hand Vac unit to the Stick Vac by inserting the Hand Vac air intake
nozzle into the opening located in the main body of the Stick Vac and pushing the
handle gently towards the Stick Vac until it clicks into place.
5. To open the dust cup compartment, simultaneously press the dust cup release
buttons on the Hand Vac unit and twist to remove. Ensure the dust cup filter is
inside, then re-attach the dust cup container to the Hand Vac unit.

USING THE HAND VAC
Remove the Hand Vac from the Stick Vac by pressing the release button and gently
pulling the unit away from the Stick Vac by the handle.
EMPTYING THE STICK VAC
For best performance, empty the Stick Vac and clean the dust cup filter after each use.
1. Press down simultaneously on both dust cap release buttons and pull off the dust
cap container.
2. Pull out the dust cup filter.
3. Empty the contents from the dust cup container.
4. Rinse the filter in cold water. Do not machine wash. Wait until completely dry. Air
dry only.
5. Replace the filter carefully into the dust cup compartment. NEVER operate the
appliance without the dust cup filter in place.
6. Reattach the dust cup container into the appliance.
USING THE MOTORISED BRUSH HEAD
NOTE: The motorised brush head is for vacuuming short pile carpets or rugs and
is for use on the Stick Vac unit only.
CAUTION: DO NOT touch the motorised head while it is in motion.
1. Ensure the appliance “On/Off” button is in the “O” position.
2. Firmly insert the motorised brush head into the air intake nozzle of the appliance,
ensuring that the contact pins are engaged in the connector slots in the unit.
3. To remove the motorised head, press the release button at the rear of the nozzle
and pull the attachment downwards.