Goldring E Series User manual

1
A
B
C
D

2

WWW.GOLDRING.CO.UK
3

Thank you for purchasing this Goldring E Series cartridge.
All cartridges in the range feature a ‘dual magnet’ generator
assembly which makes for a more accurate stereo rendition.
Featuring spherical styli with a choice of cantilevers the E1 and
E2 models are ideal as a budget replacement for an obsolete
cartridge. The E3 model, with its refined elliptical stylus, is a
worthwhile upgrade for those wishing to squeeze even more
information from the record groove.
CARTRIDGE MOUNTING
The E Series cartridge range is compatible with all tonearms
having standard 12.7 mm (0.5 in) fixing centres. For correct
alignment a stylus protractor may be required depending on
your tonearm manufacturer’s recommendation. Remove the old
cartridge from the tonearm. Working with the stylus guard still
in place, proceed to connect the colour coded tonearm leads
to the corresponding connection pins on the rear of the new
cartridge (see Fig. 1). A=Hot Left (White), B=Cold Left (Blue),
C=Hot Right (Red), D=Cold Right (Green).
Warning: Under no circumstances should the headshell leads
be soldered directly to the contact pins on the cartridge. Heat
applied to the contact pins will cause irreversible damage to the
internal components.
Use only the socket head mounting screws provided. Insert
the screws from the top and loosely attach the cartridge to the
headshell so that its position can still be adjusted. Refer to your
tonearm manufacturer’s instructions to properly set the exact
position of the cartridge within the headshell. Only when this
is set to the tonearm manufacturer’s specified position will the
cartridge perform to its full potential. Finally, tighten the screws
using the allen key provided. To avoid damage do not over
tighten the screws.
PLAYING WEIGHT
The recommended playing weight for all models is 2.0 g. Refer
to the manufacturer’s instructions for the set up procedure
specific to your tonearm. Do not forget to remove the stylus
guard before setting the playing weight. Do not exceed the
maximum specified playing weight. To prevent damage when
not in use, remember to refit the stylus guard.
AMPLIFIER CONNECTIONS
The E Series cartridge range features moving magnet
technology and should therefore only be connected to the MM
or ‘Phono’ input of your integrated amplifier or pre-amplifier.
STYLUS REPLACEMENT
EN E SERIES
MOVING MAGNET CARTRIDGES

STYLUS REPLACEMENT
Goldring styli are manufactured to the highest possible
standard, however it is vital that the condition of the stylus is
regularly checked. If properly cared for a spherical diamond
stylus can last up to 500 hours before wear causes noticeable
degradation of performance. In the case of an elliptical
diamond stylus the expected lifespan can be extended up to
1000 hours. A damaged or worn stylus will cause irreparable
damage to your precious vinyl collection and should be
replaced immediately. When a replacement stylus is required,
use only a genuine Goldring stylus assembly.
Replacement procedure: Grasp the stylus housing as shown and
withdraw it gently from the cartridge (see Fig. 2). To replace the
stylus, grasp the stylus housing very carefully between thumb
and forefinger, insert the square boss into the aperture in the
cartridge body and gently push home as shown until the stylus
housing is flush with the body (see Fig. 3).
Warning: Never use force when replacing the stylus assembly.
TECHNICAL SPECIFICATION
Model Variations
Model name:
Product code:
Colour:
Cantilever:
Stylus profile:
Stylus radius:
Replacement stylus:
Transducer Characteristics
Frequency range:
Channel balance:
Channel separation:
Sensitivity:
Static compliance:
Vertical tracking angle:
Electrical Characteristics
Load resistance:
Load capacitance:
Internal inductance:
Internal resistance:
Mechanical Characteristics
Cartridge mass:
Fixing centres:
Playing weight:
GUARANTEE
This cartridge is guaranteed against electrical and mechanical
faults for one year from date of purchase. This guarantee does
not include worn styli, and is invalidated if the instructions are
not complied with or if any unauthorised modification, repair
or alteration has been attempted.
20 Hz – 20 kHz
1.5 dB at 1 kHz
>20 dB at 1 kHz
3.5 mV (1 kHz @ 5 cm/sec)
20 mm/N
20º
47 kΩ
100 – 200 pF
400 mH
410 Ω
6.9 g
12.7 mm (0.5 in)
1.5 g – 2.5 g (2.0 g recommended)
E1
GL0054
Red
Carbon
Spherical
0.6 mil
GL0055
E2
GL0056
Green
Aluminium
Spherical
0.6 mil
GL0057
E3
GL0058
Violet
Aluminium
Elliptical
0.3 x 0.7 mil
GL0059