golmar FA-GB2/A User manual

FA-GB2/A POWER SUPPLY INSTRUCTIONS
1. Introduction:
2. Terminal description:
4. Wiring:
Open the AC protection cover:
1. Push the cover bottom towards
the center with your hand.
2. Turn over and pull it out.
5. Specification:
Input Voltage:
Input Frequency:
Rated Output Voltage:
Rated Output Current:
Working Temperature:
Dimensions:
100~240Vac
50~60 Hz
26 Vdc + 2V
1.5A
-10ºC ~ 50ºC
140*90*60mm
3. Installation:
1: Mount the din rail to the wall with wallplugs and screws that
are suplied with power supply.
2: Place the power supply simply pressing it.
N: AC input.
L: AC input.
:
Ground terminal
LED: Power indicator, always on when plug in power.
CN: Do not take off the jumper connected in CN.
.
BUS(M): Monitor connection bus terminal.
BUS(PL): Door panel connection bus terminal.
Notes:
1. The installation and handling of this equipment must be
performed by authorised personnel and without the power
connected.
2. Do not take off the jumper connected in CN.
6. Warning:
Din rail.
Din rail.
DIN rail latch release.
BUS(M)
Connect to monitor Connect to door panel
BUS(PL)
FA-GB2/A power supply has been exclusively designed to be used
on Golmar GB2 video door entry system with Thera monitors.
Golmar will not be responsible of the possible damages caused for
an improper use or when used for other purposes than the
specified.
Features:
- Universal AC input/full range.
- Multi protection: Short circuit, overload and over voltage.
- Integrated with Bus splitter (monitor/ door panel).
- Additional Bus splitter (monitor/ door panel) is not needed.
- DIN 46277 rail mounting.
3. When the installation and wiring works are finished, place the
protection cover before replacing the electrical current.
-This device has been exclusively designed to be used on Golmar
GB2 video door entry system. Golmar will not be responsible of the
possible damages caused for an improper use or when used for
other purposes than the specified.
-The installation and handling of this equipment must be performed
by authorised personnel and without the power connected.
-Install the power supply in a dry and protected place with enough
ventilation, without risk of drip or water projections.
-Install the power supply according to your country rules.
-Do not use excesive force when tightenning the power supply
connector screws.
-The device must be protected by using a thermo-magnetic circuit
breaker and connecting it to ground.
-The power supply must be unplugged from mains during
installation or maintenance progresses.
-Once the power supply has been installed, place the supplied
protection cover on the mains input connector (' ' 'N' 'L' 'L').
-Before switching the system on, check that there is no shortcircuit
on the installation.
-In case of system failure, unplug it from mains by using the thermo-
magnetic circuit breaker and contact an authorised Golmar after
sales service.
-This document must be kept together with the device.
N L L
LED
CN
1 2 3
BUS(M) BUS(PL)
.
100~240 Vac
.
NL
MODEL: FA-GB2/A
PRI: (N - L) 100-240Vac 50-60Hz
OUT: (BUS) 26Vdc + 2V / 1.5A
.
L
AC Input
100~240Vac
CN
1 2 3
N L L
*
*

1095 Budapest, Mester utca 34.
Tel.: *218-5542, 215-9771, 215-7550,
216-7017, 216-7018 Fax: [phone]
Mobil: 30 940-1970, 30 959-0930
E-mail: [email protected] Web: www.delton.hu
www.golmar.hu
1141 Budapest, Fogarasi út 77.
Tel.: *220-7940, 220-7814, 220-7959,
220-8881, 364-3428 Fax: [phone]
Mobil: 30 531-5454, 30 939-9989