Using your remote control
Channels and volume
First-time installation
Audio description and subtitles
3
5
4
6
Turns the receiver volume off Selects options on the on-screen menu
Switches the receiver on and off (into
standby) Gives digital text
to
Chooses channel numbers and numbers
on menus that relate to different options
Exits the menu system and electronic programme
guide (EPG), and goes back to the last
programme you were watching
Switches subtitles on and off Returns to the previous menu screen in the
menu system
Adjusts the aspect ratio (height and width)
of the screen when using 4:3 display
modes
Enters and exits the electronic programme guide
(EPG)
Switches the audio description on or off Enters and exits the channel list screen
Enters and exits the menu screen Switches between the channel you’re watching
and the channel you were previously watching
Increases or reduces the receiver volume
This is used to go up and down the channel list a
page at a time and to go up and down a channel
at a time when viewing a programme
Moves around the on-screen menus
Green, blue
yellow and
red buttons
Changes or goes to different options when on
digital text pages. These buttons are also used in
the electronic programme guide (EPG)
Gives programme information on the TV
screen
This button turns off the signal from the
reciever’s SCART socket. The TV will go back to
its previous mode for example, Analogue TV
To change the volume
The volume buttons on the remote control change the receiver volume only. You may also need to change your TV•
volume.
To increase the volume, press the ‘Vol +’ button.•
To reduce the volume, press the ‘Vol -’ button.•
To select a specific channel
To enter the channel number, press the• to number buttons.
To change the channel
Press the ‘Ch +’ button to move up a channel.•
Press the ‘Ch -’ button to move down a channel.•
The first time you switch on your receiver, you will see a screen like the one below.
(You may need to press ‘AV’ on your remote control before
you see this screen.)
If the signal strength is above 50%, press the• button on your
remote control. If the signal strength is below 50%, you may need
to reposition your satellite dish and check the connecting cables.
The receiver will search for the Network ID and Transport ID.•
When these have been found, press the button on your remote
control.
Enter your postcode using the ‘number’ buttons on the remote•
control. Each time you press a number button, it scrolls through
the available numbers and letters shown on that button. You do
not have to enter a space in the postcode, as the receiver will
automatically do this when you press the ‘OK’ button.
You will also need to select the type of TV screen you have by•
pressing the button on your remote control.
Press the• button on your remote control and wait for the receiver to autotune. This may take a few minutes.
When the autotune has finished, the first available channel will be shown.•
This receiver has audio description and subtitle services. Many programmes have audio description
and subtitles available, for people with hearing or sight problems.
Press the `Info’ button at any time to view the information display. If the or icons are
displayed, audio description or subtitles are available for the current programme.
Audio descriptions
To switch on audio description, press the• button. Audio description on will be shown on the screen and you
will hear a high-pitched beep if AD is available. When AD is not available, you will hear a low-pitched beep.
To switch off audio description, press the• button. Audio description off will be shown on screen and you will
hear a low-pitched beep.
For more information on audio descriptions, please read the user guide. (See page 27.)
Subtitles
Press the• button to turn on subtitles. Your TV will display ‘subtitles on’ for a short time.
Press the• button to turn off subtitles. Your TV will display ‘subtitles off’ for a short time.
For more information on subtitles, please read the user guide. (See page 27.)
GFSAT102DHS/Rev1-15-04-11
