Google jamboard User manual

User Manual (English)

Safety Instructions
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than those specified in this
document may result in exposure to shock, electrical hazards and/or mechanical hazards.

• Consult a service technician if the Jamboard does not operate normally when you have followed the instructions
in this manual.
• The casing cover should be opened only by qualified service personnel.
• Keep the Jamboard dry. To avoid electric shock, do not expose it to rain or excessive moisture.
• To avoid the risk of shock or permanent damage to the set do not expose the Jamboard to rain or excessive moisture.
• For doors or covers intended to be removed by operator for installation of accessory devices, instructions shall be
provided for the correct removal and reinstallation of the door.
Maintenance:
• To protect the Jamboard from possible damage, do not put excessive pressure on the LCD panel. When moving
the Jamboard, grasp the frame to lift; do not lift the display by placing your hand or fingers on the LCD panel.
• Unplug the Jamboard if you are not going to use it for an extensive period of time.
• The Jamboard touch-display may be wiped with a dry cloth. However, never use organic solvent, such as, alcohol,
or ammonia-based liquids to clean the Jamboard.
• To avoid the risk of shock or permanent damage to the set, do not expose the Jamboard to dust, rain, water or an
excessively moist environment.
Read and follow these instructions when connecting and using the Jamboard:
Operation:
• Keep the Jamboard out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the back of the display.
• When positioning the Jamboard, make sure the power plug and outlet are easily accessible.
• When turning off the Jamboard by detaching the power cord, wait 6 seconds before re-attaching the power
cord for normal operation.
• Ensure the use of an approved power cord provided by Google at all times. If your power cord is missing,
please contact your local service center.
• Do not subject the Jamboard to severe vibration or high impact conditions during operation.
• Do not knock or drop the Jamboard during operation or transportation.
• Unplug the Jamboard if you are not going to use it for an extensive period of time.
• Unplug the Jamboard if you need to clean it with a slightly damp cloth. The screen many be wiped with
a dry cloth when the power is off. However, never use alcohol, solvents or ammonia-based liquids.

IMPORTANT: Always activate a moving screen saver program when you leave the Jamboard unattended. Always activate a
periodic screen refresh application if the unit will display unchanging static content. Uninterrupted display of still or static images
over an extended period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your screen. This is a well-
known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will disappear
gradually over a period of time after the power has been switched off.
WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. This is also not
covered under the terms of your warranty.
RF Warning:
Federal Communication Commission Interference Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• If the Jamboard becomes wet, wipe it with dry cloth as soon as possible.
• If a foreign substance or water gets in the Jamboard, turn the power off immediately and disconnect the power cord.
Then remove the foreign substance or water, and send the unit to the maintenance center.
• Do not store or use the Jamboard in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of the Jamboard and ensure a longer lifetime, we strongly recommend using
the Jamboard in a location that falls within the following temperature and humidity ranges.
-- Temperature: 0-40°C 32-104°F
-- Humidity: 20-80% RH
Service:
• The casing cover should be opened only by qualified service personnel.
• If there is any need for repair or integration, please contact your local service center.
• Do not leave the Jamboard under direct sunlight.
!
If the Jamboard does not operate normally, having followed the
instructions set out in this document, please contact a technician
or your local service center.

- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Frequency Band EIRP (dBm) EIRP (mW)
2402 - 2480 MHz (Bluetooth) 12 16
2412 - 2472 MHz 20 100
5180 - 5320 MHz 23 200
5500 - 5700 MHz 23 200
5745 - 5825 MHz 14 25
The 5150 - 5350 MHz is restricted indoor use only
AT BE BG CH CY CZ DE DK EE PT SI
ES FI FR GB GR HU HR IE IT RO SK
IS LI LT LU LV MT NL NO PL SE TR
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
Federal Communications Commission (FCC) Notice (U.S. Only):
NOTE: This equipment has been tested and found to comply with the limits for a Class A digita device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

End-of-Life Disposal
Your new Jamboard contains materials that can be recycled and reused. Specialized companies can
recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old display from your local dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations.
For additional information on recycling contact www.eia.org (Consumer Education Initiative).
EC Declaration of Conformity
This device complies with the requirements set out in the Council Directive on the Approximation of the Laws of the Member
States relating to Electromagnetic Compatibility (2014/30/EU), Low-voltage Directive (2014/35/EU), RoHS directive (2011/65/EU) and
Radio Equipment Directive (2014/53/EU).
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20 cm between the radiator & your body.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains
FCC ID: ARS-SMMTN28C01”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module
in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.

Waste Electrical and Electronic Equipment - WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing
used electrical and electronic appliances, this product may not be disposed of with normal household waste. You
are responsible for disposal of this equipment through a designated waste electrical and electronic equipment
collection. To determine the locations for dropping off such waste electrical and electronic, contact your local
government office, the waste disposal organization that serves your household or the store at which you purchased
the product.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Europe - EU Declaration of Conformity
This device complies with the essential requirements of the Radio Equipment Directive(2014/53/EU), The following test methods
have been applied in order to prove presumption of conformity with the essential requirements of the Radio Equipment
Directive(2014/53/EU).
EN 50581: 2012 Technical documentation for the assessment of electrical and electronic products with respect to the restriction of
hazardous substances.
This product has been tested and found to comply with the harmonized standards for Information Technology Equipment, these
harmonized standards pubilished under Directives of Official Journal of the European Union.
Warning:
This equipment is compliant with Class A of EN55032/CISPR 32. In a residential environment this equipment may cause radio
interference.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 20cm between the radiator & your body.

1
1. Unpacking
1.1 Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2 Package Contents
Wall Mounted Floor Standing
• Display
• Triangle Cover
• Wall Plate
• Tray Arms
• Accessory Tray
• Eraser
• Accessory Box
• Cleaning Cloth
• Power Cord (5.9 ft)
• Installation Screws
• Stylus
• SPIDF Adapter
• Display
• Triangle Cover
• Frame
• Base
• Accessory Tray
• Eraser
• Accessory Box
• Cleaning Cloth
• Power Cord (10.5 ft)
• Power Cord Grommet
• Installation Screws
• Stylus
Table Of Contents
1. Unpacking and Installation............................................................................. 1
1.1. Unpacking.................................................................................................................................1
1.2. Package Contents................................................................................................................1
2. Functions.................................................................................................................3
3. Operation................................................................................................................ 6
3.1. OSD Keypads......................................................................................................................... 6
3.2. OSD functions...................................................................................................................... 6
3.3. Touch Operation..................................................................................................................7
3.4. Tools Operation................................................................................................................... 9
4. Pixel Defect Policy............................................................................................ 10
4.1. Pixels and Sub-Pixels.....................................................................................................10
4.2. Types of Pixel Defects + Dot Definition.............................................................11
4.3. Dark Dot Defects...............................................................................................................12
4.4. Proximity of Pixel Defects..........................................................................................12
4.5. Pixel Defect Tolerances................................................................................................13
4.6. MURA ........................................................................................................................................13
5. Cleaning and Troubleshooting ....................................................................15
5.1. Cleaning....................................................................................................................................15
5.2. Troubleshooting................................................................................................................16
6. Technical Specifications................................................................................. 17

2 3
2. Functions
2.1 Rear Control Panel
3
7
2
8
1
9
4
11
10
56
Display
Accessory Tray
Frame + 10.5’ Cord
Power Cord Grommet
Screws
Base 5.9’ Cord
Tray Arms
Wall Plate
Rear Triangle
Accessory Box SPIDF Adapter
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies
with the safety regulations of the particular country.
• You might like to save the package box and packing material for shipping the display.
• Wall mount bracket need to be installed by professionals.

4 5
2.2 Front Control Panel
2
1
1Camera
1080P resolution input.
NFC Reader
Support NFC card to access.
2
1POWER BUTTON
Switch the main power on/off. 7HDMI 2.0 HDMI video/audio input.
2VOLUME [ +/-]
Control volume output. 8AC IN AC power input from the wall outlet.
3INPUT
Use this button to select the input source. 9USB Type C Support power delivery/ USB storage/ DP input.
4MICRO USB
Update Android flash only. 10 USB 3.0 Port 1 / USB 3.0 Port 2 Connect your USB storage device.
5SPDIF OUT
SPDIF 2.1 channel output. 11 HDMI 1.4 HDMI video/audio input.
6RJ-45
Support 1000BaseT.

6 7
3.3 Touch Operation
This Jamboard display is equipped with a touch-sensitive screen and supports the Jamboard features either by single-touch or
multi-touch operation. You can touch the pictures or words on the Jamboard touch-display gently with your fingers, and the
Jamboard will react.
The following description illustrate some typical touch operation behavior. For further detail on how to run the touch operation,
please refer to the on screen instruction.
Single Tap Pan
Touch the target on
the screen with one
fingertip for one quick
tap then release.
Touch the target on the screen
with one fingertip and move
across the target without
losing direct contact, then
release.
3. Operation
3.1 OSD Keypads 3.2 OSD Functions
Power Key:
DC off/on controller.
Power ON/OFF:
Press “Power” to switch the power state.
Source Key:
Source selection.
Source Selection:
Press “Source” to switch to next source.
The source selection sequence is HDMI1 > HDMI2 > DP > Android.
Vol+ Key:
Up adjuster.
Volume:
Press “Vol+” to pop out the “Volume adjuster” menu.
And then use “Vol+” and “Vol-“ to adjust it.
Vol- Key:
Down adjuster.
Brightness:
Press “Vol-” to pop out the “Brightness adjuster” menu.
And then use “Vol+” and “Vol-“ to adjust it.

8 9
3.4 Stylus and Eraser Operation
This Jamboard display is equipped with a touch-sensitive screen and supports the use of the Jamboard stylus or eraser. You can
touch the pictures or words on the Jamboard touch-display gently with the Jamboard accessories, and the Jamboard will react.
The following description illustrate some typical touch operation behavior. For further detail on how to run the touch operation,
please refer to the on screen instruction.
Write Erase
Use the stylus to write
anywhere on the screen.
The stylus is pressure
sensitive and changes
depending on how hard
you press on the screen.
Use the eraser (microfiber side
down) to erase marks and
gestures on the screen.
NOTES:
• Avoid scratching with sharp object on the touch-display. Only fingertips and the Jamboard accessories are allowed for touch control.
• Avoid intensive light, spotlight, or wide-spread light from direct beaming on the screen.
• Avoid installation location close to the windows or glass-doors as the direct sunlight may affect the touch-control performance.
Flick Zoom In
Touch the target on the screen
with one fingertip and brush
the surface quickly.
Touch the target on the screen
with two fingertips held together
and move them apart to zoom
in (magnify) the screen image.
Zoom Out Touch and Hold
Touch the target on the screen
with two fingertips stretched
apart and move them closer to
zoom out (shrink) the screen
image.
Touch and hold the target on
the screen with one fingertip
for a while to display a context
menu or options page for an
item.

10 11
4.2 Types of Pixel Defects + Dot Definition
Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several types of
sub-pixel defects within each category.
Dot definition = What is a defective “Dot”?
One or more defective, adjacent sub-pixel are defined as one “dot”.
The number of defective sub-pixels are not relevant to define a
defective dot. This means that a defective dot can consist of one, two
or three defective sub-pixels which can be dark or lit.
One dot = One Pixel; consists of
three sub-pixels of Red, Green,
and Blue.
4. Pixel Defect Policy
We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst
practicing stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays
are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but guarantees that
any Plasma- & LCD- displays with an unacceptable number of defects will be repaired during the warranty period in line with your
local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for the LCD screen. In order to
qualify for repair under warranty, the number of pixel defects must exceed a certain level as shown in the reference table. If the
LCD screen is within specification a warranty exchange / claim back will be refused.
4.1 Pixels and Subpixels
A pixel, or picture element, is composed of three sub-pixels in the primary colors
of red, green and blue. Many pixels together form an image. When all sub-pixels of
a pixel are lit, the three colored sub-pixels together appear as a single white pixel.
When all are dark, the three colored sub-pixels together appear as a single black
pixel. Other combinations of lit and dark sub-pixels appear as single pixels of other
colors.

12 13
4.5 Pixel Defect Tolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Plasma / LCD- display must
have pixel or sub-pixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT ACCEPTABLE LEVEL
1 lit sub pixel 2
BLACK DOT EFFECT ACCEPTABLE LEVEL
1 dark sub pixel 10
TOTAL DOT DEFECTS 12
4.6 MURA
Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels. This is known within the industry
as Mura, which is a Japanese term for “unevenness.” It is used to describe an irregular pattern or area in which uneven screen
uniformity appears under certain conditions. Mura is a result of the deterioration of the liquid crystal alignment layer and is most
commonly caused by long-term operation under high ambient temperatures. It is an industry- wide phenomenon and Mura is
not repairable. It is also not covered by our warranty terms. Mura has been around since the introduction of LCD technology and
with screens getting bigger and in operation 24/7, many displays are running in low light conditions. This all adds to the possibility
of Mura affecting displays.
4.3 Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or “off.” These are the examples of black dot defects:
One dark dot Two adjacent dark dots =
1 pair of dark dots
Two dark dots,
specifcations defnes the
minimum distance
between dark dots
4.4 Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, specifies tolerances
for the proximity of pixel defects. In the table below you can find specifications about:
• Allowed amount of adjacent dark dots = (adjacent dark dots = 1 pair of dark dots)
• Minimum distance between dark dots
• Total number of all defective dots

14 15
5. Cleaning and Troubleshooting
5.1 Cleaning
Caution when using the Jamboard
• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the Jamboard display is
usually very hot due to the high temperature of exhaust air being released through the ventilation holes. Burns or personal
injuries may occur if any body parts are brought too close. Placing any object near the top of the display could also result
in heat related damage to the object as well as the display itself.
• Be sure to disconnect all cables before moving the Jamboard. Moving the Jamboard with its cables attached may damage
the cables and thus cause fire or electric shock.
• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or
maintenance procedure.
Front Panel Cleaning Instructions
• The front of the Jamboard touch-display has been specially treated. Wipe the surface gently using only a cleaning cloth or
a soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess
liquid. Wipe the surface of the Jamboard touch-display to remove dirt. Then use a dry cloth of the same type to dry.
HOW TO SPOT MURA
There are many symptoms of Mura and also multiple causes. Several of these are listed below:
• Impurities or foreign particles in the crystal matrix
• Uneven distribution of LCD matrix during manufacturing
• Non-uniform luminance distribution of the backlight
• Panel assembly induced stress
• Flaws within the LCD cells
• Thermal induced stress - high temperature operation over long periods of time
HOW TO AVOID MURA
Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be
minimized by these methods:
• Lower the backlight brightness
• Use a screen saver
• Reduce the ambient temperature around the unit

16 17
6. Technical Specifications
Display
Item Specifications
Screen Size (Active Area) 54.64” (138.8 cm) LED
Aspect Ratio 16:9
Number of pixels 3840 (H) x 2160 (V)
Pixel pitch 0.315 mm x 0.315 mm
Color Depth 10 bits, 1.07billion colors
Brightness 500 cd/m
2
(Center 1 point, Typical)
Contrast Ratio 800:1 (Min.)
Viewing angle 178 (H) / 178 (V)
• Do not scratch or hit the surface of the Jamboard display with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners.
5.2 Troubleshooting
Symptom Possible Cause Remedy
No picture is displayed. 1. The power cord is disconnected
2. The power switch is not switched on
3. The display is in standby mode
1. Plug in the power cord
2. Make sure the power switch is on
3. Touch the display to exit standby
Interference displayed on the display or
audible noise is heard.
Caused by surrounding electrical
appliances or fluorescent lights.
Move the display to another location to
see if the interference is reduced.
Can see picture but no sound is heard. 1. Volume is turned all the way down
2. Mute is turned on.
1. Press [+] or [-] button to hear sound.
2. Switch MUTE off
After-images can still be seen on the
display after the display is turned off.
A still picture is displayed for an over
extended period of time.
Do not allow a still image to be displayed
for an extended period of time as this
can cause a permanent after-image to
remain on the display.

18 19
General:
Item Specifications
Power Supply AC 100 - 240V, 50 - 60Hz
Power Consumption 200 W (Max.)
130 W (Typ.)
<0.5W (standby mode)
Build version jam_kiosk_20170502-1700_RC06.155815817
Dimensions 1352(W) x 1817.4(H) x 1019.5(D) mm (Floor standing)
1352(W) x 978.7(H) x 211.5(D) mm (Wall mounted)
Weight 27.27Kg (Floor Standing)
6.85Kg (Wall mounted)
Gross Weight 69.5Kg
Tilt 0º~18º
In/Out Terminals
Item Specifications
SPDIF Output SPDIF Port Serial digital audio output when input is HDMI
RJ-45 RJ-45 Jack x 1 (8 Pin) 1000BaseT
HDMI Input HDMI Jack x 2
(Type A) (19 Pin)
Digital RGB:TMDS (Video + Audio)
MAX: Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA), 4K/2K 30/60Hz (HDMI2.0 only)
Audio - 48 KHz/ 2 Channel (L+R)
Separate to HDMI 1.4 and HDMI 2.0
USB Input USB x 2 (Type A) USB 3.0
USB Input USB x 1 (Type C) USB Type C@3A/storage/DP 1.2 input

20
Environmental Condition:
Item Specifications
Temperature Operational 0 ~ 40°C
Storage -20 ~ 60°C
Humidity Operational 20 ~ 80% (without condensation)
Storage 5 ~ 95% (without condensation)
Altitude Operational 0 ~ 3,000 m
Storage / Shipment 0 ~ 9,000 m