GOREK GTO-51 Product guide

GOREK TECHNOLOGIES
101, J.B. Shopping Center-1, Matawadi, L H Road, Surat, Gujarat
Contact: [phone]
Manual Book
Automatic Mini Oil Press Machine
Model: GTO-51

OIL Press Machine GTO-51
GOREK TECHNOLOGIES
101, J.B. Shopping Center-1, Matawadi, L H Road, Surat, Gujarat
Contact: [phone]
INTRODUCTION
1. Main Machine 2. Hopper
3. Trim Hand Wheel 4. Chamber
5. Heater 6. Lead Slag
7. Oil Guide Groove 8. Cover
9. Filter Screen 10. Protect Switch
11. Temperature Controller 12. Reversion
13. Stop 14. Start press

OIL Press Machine GTO-51
GOREK TECHNOLOGIES
101, J.B. Shopping Center-1, Matawadi, L H Road, Surat, Gujarat
Contact: [phone]
PRODUCT DESCRIPTION
•Mini Commercial Oil Press Machine is used for Pressing of Peanuts, Coconut, Sesame,
Soybean, Walnuts, Sunflowers seeds, Vegetable seeds, Flax seeds, Almond, Castor
Seeds, Mustard seeds and so on.
•Oil extracting that is depends on the oil seeds.
OPERATION
1. Connect to the power and turn on the switch. 220V- 50 Hz, please use the single phase
three socket, the outlet should be a reliable ground protection.
2. Push on the power switch “10”, power indicator “11” shine means power on.
3. Pressing heating switch “12”, waiting 10 min to heating. No need to turn off the
heating switch.
4. How to Set Temperature in Controller:

OIL Press Machine GTO-51
GOREK TECHNOLOGIES
101, J.B. Shopping Center-1, Matawadi, L H Road, Surat, Gujarat
Contact: [phone]
5. First put a small amount of raw material for pressing, to test whether the machine can
be normal operation. Put the material in the hopper “2”, fine tuning the trim hand
wheel “3”, clockwise turning the hand wheel, do not rotate around 360 degrees.
6. Press start button “15”, if any abnormal press “14”. If any foreign body enter the
pressing chamber, stop the machine and press reversion button “13”, when foreign
body out of machine then continue pressing.
7. Press the button “12” when materials pressing finished. And let the machine working
empty for 3-5 minutes. Turn off “12” and “14”.
Main Material Oil Yield Rate
Raw Materials
Oil yield rate
Raw Materials
Oil yield rate
Sesame
42-50%
Sunflower seed
30-35%
Peanuts
38-48%
Walnut
32-40%
Rapeseed
30-35%
Flaxseed
28-35%
Coconut
45-55%
MATERIALS
COCONUT: Make small pieces of dry coconut and set temperature to about 80-100oC.
After 5-10 minutes push squeezing button and then input coconut to hopper.
(Note: 15 minutes after squeezing started, off heating if you fill enough heating.)
PEANUT: Roast the peanut and then add 10 - 12 % water, continue roasting for some
minutes. Until the water dries out, this can make the oil purer.
SESAME: Black sesame can be pressed directly. White sesame need to like the peanut.
Add 10 - 12 % water and then roast.

OIL Press Machine GTO-51
GOREK TECHNOLOGIES
101, J.B. Shopping Center-1, Matawadi, L H Road, Surat, Gujarat
Contact: [phone]
ATTENTION
1. Operators must understand the technique and performance of oil press machine, so
that can operate independently.
2. Prohibited metal or other hard objects into the pressing chamber. Do not use the
metal bar into feed inlet.
3. When pressing screw shaft jammed, not troubleshooting, prohibit forced to start, to
avoid damage to parts and other accidents.
4. The oil cake should cool to below 40 deg. So that can be stacked and packaged to
prevent spontaneous combustion.
5. Prohibit use high-power motors to drive the oil press.
6. While the machine is working, the operator shall not leave.
DISASSEMBLE
1. Press the reverse button to make the machine swivel back for 30 seconds so that the
pressing chamber and screw can be easily separated.
2. Do remember to put on gloves for disassemble the pressing frame when the extraction
is just finished. OR let the machine cool down for a while and then disassemble.
3. Take out the pressing screw and chamber.
MACHINE PARAMETERS
Model: GTO-51
LxWxH: 59x29x46 CM
Weight: 40 Kg
Voltage: 220V/50Hz
Capacity: Up to 10 Kg/hr
Power: 1500 W
COMMON PROBLEM AND SOLUTION
1. If any foreign body enter the pressing chamber: - Stop the machine and press
reversion button, when foreign body out of machine the cleaning the chamber and
screw, continue pressing.
2. Screw cannot take out from chamber: - Put it the machine and let the machine idle
away 5 minutes.
3. Power off above 30 minutes: - Stop adding material, turn off power and plug. Clear
the hopper. When power gets on, continue pressing after heating about 20 minutes.
If the oil press machine still cannot be working normally, the please get out the
chamber and screw. After clear them, start to press again.

OIL Press Machine GTO-51
GOREK TECHNOLOGIES
101, J.B. Shopping Center-1, Matawadi, L H Road, Surat, Gujarat
Contact: [phone]
Temperature Controlling Range
MATERIAL
TEMPERATURE (OC)
Peanuts
180-220
Sesame
170-220
Mustard
180-210
Flax Seeds
170-200
Almonds
180-220
Sunflower
180-210
Coconut
60-100
Safflower
190-210
Walnut
160-190
Kalonji
120-150
Soybeans
170-210
Castor
180-220
Moringa Seeds
80-120
Malkangni
60-80