Gorenje GHS64-ORA-S Guide

Combined and gas built-in cooking hob
MT IE GB Instructions for use, installation,
and connection

266871
Combined and gas built-in hob is intended for use in
households.
Our products are packed in environment-friendly materials which
can be recycled, disposed of, or destroyed without imposing any
burden on the environment.
Instructions for use are intended for the user. They describe the
appliance and its operation. The instructions apply to various
types of appliances and may therefore include description of
functions that may not be available on your appliance.
These instructions are only valid of the country symbol is
indicated on the appliance. If there is NO county symbol in the
appliance, technical instructions should be observed for adapting
the appliance to comply with the requirements and regulations
for use in your country.
The appliance must be connected in compliance with the
instructions attached to it, as well as in compliance with relevant
regulations and standards. The connection may only be
performed by a qualified person.
The rating plate indicating the basic information on the appliance
is attached to the lower side of the hob.
Instructions for use
Instructions for
connection
Rating plate
Important warnings ........................................................3
Appliance description ...................................................4
Cooking zones................................................................5
Operating the gas burners.............................................7
Cleaning and maintenance............................................8
Special warnings and fault reporting .........................10
Installation..................................................................... 11
Connecting the appliance to the power mains..........13
Connecting the cooking hob to the gas supply ........15
Nozzle table ..................................................................17
Technical characteristics.............................................18
Dear customer!
2
Combined and gas built-in cooking hob

266871
• Installation of the appliance into a kitchen worktop and its connection to the power mains and the
gas supply may only be performed by an adequately qualified technician.
• When the appliance is in use, additional heat and moisture are emitted into the room. When the
appliance is used for a prolonged period of time at a high performance level, intensive ventilation
or use of kitchen hood may is required in the room where the appliance is installed.
• Do not use the gas burners, if the flame seems unstable.
• If you smell gas in the room, immediately close the gas supply valve either on the gas bottle or
gas pipeline, extinguish all sources of open fire (including cigarettes), aerate the room, do not
turn on any electric appliances, and call a natural gas expert.
• The main gas supply valve should also be closed if gas burners will be out of use for a long
period of time (e.g. when going on holiday).
• Do not leave small children unattended when the appliance is in operation. Risk of burning and
scalding!
• During cooking, the overheated fat or oil on the hob may ignite. There is a risk of burning and
fire; therefore, control the cooking process at all times.
• Do not use the cooking hob for room heating. Do not place empty pans on the hob.
• Make sure that the parts of the burners are correctly positioned / installed.
• Glass ceramic hobs should not be used as a worktop. Sharp objects may cause scratches.
• Preparing food in thin aluminum of plastic containers on hot cooking zones is not allowed. Do not
place any plastic objects or aluminum foil on the glass ceramic hob.
• If there is a wall power outlet located near the hob and another appliance is plugged into it, make
sure the power cord does not come into contact with the hot cooking zones.
• Do not store any temperature-sensitive objects, materials, or substances underneath the hob,
e.g. detergents, sprays, etc.
• Do not use the glass ceramic hob if it is cracked or broken. If any visible crack appears,
immediately unplug disconnect the appliance from the power supply.
• In case of a failure of the appliance, immediately disconnect the appliance from the power mains
and contact the service center.
• Do not use steam cleaners or high-pressure cleaners to clean the cooking hob, as this may
result in an electric shock.
• The appliance is manufactured in compliance with the relevant effective safety standards.
Nevertheless, we strongly recommend that persons with impaired physical, motoric, or mental
capacity, or persons with inadequate experience or knowledge, do not use the appliance unless
attended by a qualified person. The same recommendation applies when the appliance is used
by persons of less-than-legal age.
The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of thisproduct. For more detailed information about recycling
of this product, please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
3
Important warnings

266871
(equipment - depending on the model)
Upper side of a combined cooker with
gas cooking zones
Upper side of the cooking hob with a
gas burners and a triple cooking field
1. Cooking zone rear left
2. Cooking zone rear right
3. Control knobs
4. Cooking zone front right
5. Cooking zone front left
Gas
gas valve is closed
maximum power
minimum power
(depending on the model)
4
Appliance description
Control knob

266871
Gas cooking zones
• If you wish to quickly fry some food, set the gas burner to
the maximum power initially and reduce the power as your
continue.
• With some models, gas burners are fitted with
thermoelectric protection devices. If the burner flame is
extinguished accidentally or unintentionally (e.g. when
some liquid boils over or when there is draught in the
room), gas supply is automatically cut off, thus preventing
the gas to be emitted into the room.
• If the flame on a gas burner without thermoelectric
protection, the gas will be emitted into the room!
• Gas burner cover should always be placed very carefully on
the burner crown. Make sure the slots on the burner crown are
never obstructed.
1Burner crown cover
2Burner crown with the support for the burner cover
3Thermo-element (only with protected burners, available in
some models)
4 Spark plug
5Nozzle
• Correctly selected cookware will enable optimum cooking time
and gas consumption. Pan diameter is the most important
parameter.
• Flames that reach over the edge of a pan that is too small, can
damage the cookware; furthermore, gas consumption is higher
in such cases.
• For combustion, the gas also needs air. If a pan is too large,
air supply to the burner is insufficient; as a result, combustion
effect is lesser.
Grid extension (only available with some models)
Use the extension when using a pan of a smaller diameter. Place
the extension on the grid above the auxiliary burner.
Important warnings
Cookware
5
Cooking zones

266871
Wok accessory (for the double burner (Wok))
• Use the extension when preparing food in a Wok.
• Place the extension over the burner grid support.
Burner type Pan diameter
Large (3,0kW) 220-260 mm
Normal(1,75kW) 180-220 mm
Auxiliary (1,0kW) 120-180 mm
Triple burner (3.8kW) 220-260 mm
Important warnings regarding the glass ceramic hob
• Cooking zone reaches the selected power level or temperature
very quickly; however, the area surrounding the cooking zones
remains relatively cool.
• The hob is resistant to temperature changes.
• The hob is also impact-resistant. The pans may be placed onto
the hob roughly without damaging the hob.
• Glass ceramic hobs should not be used as a worktop. Sharp
objects can cause scratches.
• Preparing food in thin aluminum of plastic containers on hot
cooking zones is not allowed. Do not place any plastic objects
or aluminum foil on the glass ceramic hob.
• Never use a glass-ceramic hob that is cracked or broken.
If an object falls on the hob with a sharp edge downwards,
this could cause the hob / glass ceramic panel to break. The
consequences are visible immediately, or only after a while. If
any visible crack should appear, immediately disconnect the
appliance from the power supply.
• If sugar is spilt on a hot glass ceramic hob, or a sugar-laden
food, immediately wipe the hob.
6

266871
Models with two gas burners:
• Operate the gas burners using the knobs on the hob. Power
levels are indicated on the knobs by large and small flame
symbols (see section Appliance description).
• Rotate the knob through the large flame position ( ) to the
small flame position ( ) and back. Operation interval lies
between the two flame symbols.
• Gas burners can be ignited using the electric spar plug built
into each gas burner (only available with some models).
Before rotating the knob, it should first be depressed.
Single-handed ignition
• In order to ignite the gas burner, press the selected burner
control knob and rotate it to the maximum power (flame)
position. An electric spark will be generated automatically,
igniting the releasing gas.
• If the electric ignition should not work due to a power failure or
damp spark plugs, the gas can also be ignited using a match
or a gas lighter. After igniting the gas, keep the control knob
pressed for another ten seconds, until the flame settles.
• The flame can then be set between the maximum and
minimum level. Any setting between ( ) and ( ) is not
recommended, as the flame is not stable in this interval and
may be extinguished.
If the burner hasn’t ignited after the knob has been
depressed for fifteen seconds, close the burner and
wait at least one minute. Then, repeat the ignition
process.
If the burner flame is extinguished (for any reason),
close the burner and wait at least one minute before
attempting to re-ignite it.
• To extinguish the flame and close the burner gas supply, rotate
the control knob to the right, to the ‘OFF’ position ( ).
Ignition and operation of
the burners
7
Operating the gas burners

266871
After each use of the glass-ceramic hob, wait for it to cool
down and clean it; otherwise, even the smallest food residue will
be burnt onto the hot surface next time you use the appliance.
For regular cleaning and maintenance of the glass-ceramic
surface, use special conditioning agents which form a
protective layer on the surface, shielding it from dirt. Before each
use, wipe any dust or other particles from the hob surface and
pan bottom as these could scratch the surface (Figure 1).
Careful: steel wool, abrasive sponges, and abrasive detergents
can scratch the hob surface. Glass ceramic surface can also be
damaged by aggressive sprays and inappropriate or insufficiently
shaken (mixed) liquid cleaning agents (Figure 1 and Figure 2).
Signage may be worn when using aggressive or abrasive
cleaners or cookware with damaged bottom (figure 2).
Light stains can be removed by a damp soft cloth; then, wipe
the surface dry (Figure 3).
Water stains can be removed using a mild solution of vinegar;
however, do not use this solution to clean the frame (only with
some models, as it may become dull. Do not use aggressive
sprays or decalcification agents (Figure 3).
Heavier stains can be removed using special agents and
utensils for cleaning the glass-ceramic hobs. When using these
products, follow the instructions provided by their respective
manufacturers.
Make sure any residues of cleaning agents are thoroughly
removed, as they could damage the glass-ceramic hob when
the cooking zones heat up (Figure 3).
Remove stubborn and burnt residues with a scraper (figure 4).
Be careful when handling the scraper to prevent injury.
Only use the scraper when dirt cannot be removed
with a wet cloth or special cleaners for glass ceramic
surfaces.
Hold the scraper at the correct angle (45° to 60°). Gently press
the scraper against the glass and slide it over the signage to
remove the dirt. Make sure the plastic handle of the scraper (in
some models) does not come into contact with a hot cooking
zone.
Do not press the scraper perpendicularly against the
glass and do not scratch the hob surface with its tip or
blade.
Cleaning
Figure 2
Figure 3
Figure 4
Figure 1
8
Cleaning and maintenance

266871
Sugar and sugar-laden food may permanently damage the glass-
ceramic surface (Figure 5); therefore, they should be removed
from the glass-ceramic surface as soon as possible, although
the cooking zone may still be hot (Figure 4). Any change in the
color of the glass-ceramic surface does not affect its operation
or the stability of the surface. Such discolorations are mostly
a result of burnt food residues or use of cookware made of
materials such as aluminum or copper; these stains are difficult
to remove.
Warning: All damage described above predominantly relates to
the aesthetics, i.e. appearance of the appliance and do not affect
its functionality directly. Such errors cannot be the subject of a
warranty claim.
To clean the grid, cooking hob surface, and parts of the burner,
use hot water with some dishwashing detergent. Clean the
thermo-element and the spark plug with a soft brush. These
parts must be kept impeccably clean, as only then will they
operate correctly. Clean the crown and the burner cover. Be
particularly careful to keep all exit slots on the crown clean and
unobstructed. After cleaning, dry all parts thoroughly and replace
or reassemble them correctly. Parts that are placed askew will
make lighting the burners more difficult.
Warning: Burner covers are coated in black enamel. Due to high
temperatures, discoloration is unavoidable; however, this will not
affect the operation of the burners.
Figure 5
Gas cooking zones
9

266871
What happened...? Possible cause What to do?
The burners will not burn
The flame is uneven / unstable
Flame is uneven due to a
wrong gas power setting.
Have an expert check he gas
pipeline!
The flame from the burners
suddenly changes
Wrongly assembled parts of the
kitchen hob
Assemble the burner correctly.
Burner ignition takes more time Wrongly assembled parts of the
kitchen hob
Assemble the burner correctly.
The flame is extinguished
shortly after ignition
Knob pressed too short or to
weakly.
Keep the knob depressed for
a longer period of time. Before
releasing it, pres it harder.
The grid has discolored in the
burner area?
This is a commonplace
phenomenon resulting from
high temperature
Clean the grid with a metal care
detergent.
Electric power supply in general
is interrupted?
The fuse may be blown. Check the fuse in the fuse box
and replace it if it is blown.
Electric ignition of the burners
no longer works?
There are food or detergent
residues between the spark
plug and the burner.
Open and carefully clean the
opening between the spark plug
and the burner.
If the burner cover looks
unappealing...
Regular dirt Clean the burner covers with a
metal care detergent.
If the problem persists despite observing the instructions above, call
an authorized service technician. Elimination of any errors or warranty
claims that resulted from improper connection or use of the appliance
is not covered by our warranty. In such cases, the costs of repair are
borne by the user.
During the warranty period, only a service center authorized by the manufacturer may carry
out any repairs.
Before making any repairs, make sure the appliance is disconnected from the power mains either by
removing the fuse or by disconnecting the power plug from the wall outlet.
Unauthorized tampering with and repairs of the kitchen range (cooking hob) can result in electric shock
or short circuit; hence, do not attempt to perform any repairs by yourselves. Leave such tasks to an
expert or an authorized service unit.
In case of minor faults or problems with the appliance operation, check the following instructions to see
whether you can eliminate the causes by yourselves.
A visit by a service technician during the warranty period will be
charged if the appliance is not functioning because of improper
use. Store these instructions in a place where they are always
readily accessible; if pas the appliance on to another person, the
instructions should also be included.
Following is some advice on rectifying some common problems.
Important
10
Special warnings and fault reporting

266871
Important warnings
• Installation of the appliance into a kitchen worktop and its connection to the power mains may
only be performed by an adequately qualified technician.
• Veneer or other finish of the piece of kitchen furniture into which the hob is to be built in should
be treated with heat resistant glue (100°C); otherwise, the worktop finish may be discolored or
deformed.
• Cooking hob is dimensioned to be built into the worktop over a piece of kitchen furniture, with a
width of 600 mm or more.
• After installation, the front two fastening elements should be freely accessible from below.
• The kitchen furniture element underneath the hob should not be fitted with a drawer. If the
kitchen furniture element as a horizontal partition wall, it should be installed no less than 10
centimeters from the lower surface of the worktop. The space between the partition wall and the
hob must be empty; no objects should be placed into that gap.
• Hanging, or wall-mounted kitchen elements should be installed high enough not to interfere with
the work process.
• The distance between the cooking hob and the kitchen hood should be no less than indicated in
the instructions for kitchen hood installation. The minimum distance is 650 mm.
• The distance between the appliance edge and the adjacent tall kitchen furniture element should
amount to no less than 100 mm.
• Use of massive wood decoration plates or boards on the worktops behind the cooking hob is
permitted, if the minimum distance remains the same as indicated in the installation drawings.
• Minimum distance between the built-in cooking hob and the rear wall is indicated on the
installation drawing.
• Cooking hobs can be installed into worktops that are 30 to 50 mm thick.
Before inserting the appliance into the opening in the kitchen
worktop, the supplied foam gasket must be attached to the lower
side of the glass ceramic (glass) cooking hob (see figure above).
Do not install the appliance without the foam gasket!
The gasket should be attached to the appliance in the
following way:
- Remove the protective film from the gasket.
- Then, attach the gasket to the lower side of the glass,
approximately 2-3 millimetres from the edge (as shown in the
figure). The gasket must be attached along the entire length of
the glass edge and should not overlap at the corners.
- When installing the gasket, make sure that the glass does not
come into contact with any sharp objects.
Installing the foam
gasket
11
Installation

266871
• Only type EVP4.., EVP2.., ovens fitted with a cooling fan may
be installed underneath this cooking hob.
• Before installing an oven, the rear wall of the kitchen furniture
element should be removed in the area of the cooking hob
cutout. Furthermore, a gap of at least 6 mm should be left at
the front side.
NOTE!
On some appliances the gasket is already installed!
12
Kitchen worktop cutoff
dimensions

266871
• The appliance may only be connected by an authorized skilled technician.
• Electric system protection should comply with all relevant regulations.
• The connection clips can be accessed when the connection clip covers are opened / removed.
• Before connecting the appliance, make sure the voltage indicated on the rating plate is consistent
with the voltage in your home circuit.
• The rating plate with basic information is attached on the lower side of the hob.
• The electric circuit should also include an omnipolar switch that will separate the appliance from
the mains, if required, with at least 3 mm of distance between contacts. Suitable devices include
fuses, current protection switches, etc.
• The connection should be selected according to the installation possibilities with regard to current
and fuses.
• Given the protection from the risk of fire, appliances of this type may be installed in a worktop next
to a piece of kitchen furniture that is taller than the appliance (when installed); however, in this
case, a kitchen furniture element must be installed on the other side, adjacent to the appliance.
• The current conducting and isolated parts must be protected from any possibility of direct contact.
WARNING!
• Before any intervention, disconnect the appliance from the power mains. Connect the appliance in
compliance with the electric connections diagram supplied; make sure the relevant network voltage is
Important warnings
• The worktop should be installed completely horizontally.
• The cutoff surfaces should be appropriately protected.
• Attach the fastening elements (4) with the supplied screws (4)
to the front and rear wall of the cooking hob and the worktop
cutoff.
• Connect the cooking hob to the power mains and gas supply
(see instructions for connecting a cooking hob on a power
network and gas supply).
• Attach the supplied adhesive seal on the lower edge of the
cooking hob.
• Insert the cooking hob into he cutoff and press it heavily from
above towards the worktop.
• For screwing down the fixing clip it is not allowed to use
screws longer than 6,5 mm.
Installation procedure
13
Connecting the appliance to the power mains

266871
• Incorrect connection may destroy parts of the appliance,
making the warranty void.
• Before connecting the appliance, make sure the voltage
indicated on the rating plate is consistent with the voltage
in your home network. Connection voltage (230 V through
N) should be checked by a qualified technician using a
corresponding measuring device!
• Connection cable on the back of the appliance should be led in
such way that it does not touch the appliance back wall, as this
part will get very hot during operation.
230V~
L1 N
PE
NOTE:
Connection bridges are already installed on their respective
places on the clip. Screws of the connection terminals are open,
which means they do not have to be unfastened or unscrewed
any further. When fastening the screws, you may hear a slight
‘click’, which means that the screws should be fastened /
screwed in completely.
The following can be used for connection:
• Type H05 RR-F 4×1.5 rubber connection cables with a green-
yellow protective wire,
• Type H05 VV-F 4x1,5 PCV isolated connection cables with
yellow-green protective wire, or other equivalent or superior
grade cables.
Connection diagram
observed! The ground wire (PE) should be connected to the clip indicated by the earthing symbol.
• The mains cable should be fed through the fastening clip which protects it from being accidentally
pulled out.
• After connecting the appliance, turn on all cooking zones / heaters for approximately three
minutes to make sure they are operating correctly.
14

266871
• The appliance must be connected in compliance with all relevant regulations, and it may only be
used in well ventilated / aerated rooms. Before connecting or using the appliance, please read
the instruction manual.
• Before installing and connecting, make sure the local natural gas supply network and connection
(type of gas and pressure), are compatible with your appliance version.
• The version of this appliance is indicated on the rating plate.
• This appliance is not suitable for connection to a burning fumes exhaust system (i.e. a chimney).
The appliance must be installed and connected in compliance with the relevant effective
installation regulations. Special care must be taken to ensure adequate ventilation / aeration.
Important warnings
• When connecting the appliance to the gas supply, follow the
regulations of the local gas distributor.
• On the lower side, the cooking hob is fitted with a gas connection
plug with a EN ISO 10226-1 / -2 or EN ISO 228-1 (Depending on
the country-specific connection regulations.). thread.
• Also supplied with the appliance is an adapter for liquid gas and a
non-metal gasket.
• When connecting, the knee R1/2 should be held firmly to prevent
it from rotating.
• For sealing of the connection joints, use a non-metal approved
gaskets and approved sealants.
• The gaskets should only be used once. The thickness of the flat non-
metal gaskets should not be deformed more than by 25 percent.
• To connect the appliance to the gas supply, use a tested and
certified flexible hose.
• The flexible connection hose should be able to move freely. It
should not come into contact with the movable parts of the kitchen
furniture (e.g. a drawer), or the bottom of the cooking hob.
• If an electric oven is built into the kitchen element under the
cooking hob, it should be fitted with a cooling fan, and the
connection should be made using a pipe completely made of
metal (e.g. a stainless steel flexible pipe.
After connecting the gas hob, check the joints for any
leaks.
Gas supply connection plug
AEN ISO 10226-1 / -2 or EN ISO 228-1 (Depending on the
country-specific connection regulations.). connection plug
BNon-metal gasket with thickness of 2 mm
CPipe adapter for liquid gas (Depending on the country-specific
connection regulations.)
Connection
15
Connecting the cooking hob to the gas supply

266871
After the connection, check the burners for correct operation.
The flames must be clearly visible, and should be blue and green
at the center. If the flame is unstable, increase the minimum
power. Explain the use of the burners to the user and read the
instructions for use together.
• The procedure or adaptation of the cooker to another type
of gas does not require removal of the appliance from the
worktop.
• Before adapting, disconnect the appliance from the power
mains and close the gas supply valve.
• Replace the existing nozzles for nominal thermal load with
corresponding nozzles for the new gas type (see table below).
• When adapting the appliance to liquid gas, fasten the
regulation screw for minimum thermal load as far as it will go,
in order to attain minimum thermal load.
• When adapting the appliance to natural gas, release the
minimum thermal load regulation screw in order to attain
minimum thermal load, but do not rotate it by more than 1.5 turns.
Cooker burner
1Burner crown cover
2Burner crown with cover support
3Thermo-element (only in protected burners, only available in
some models)
4Spark plug
5Nozzle
Triple burner
5Nozzle
To leave the adjustment elements accessible, please observe the
following instructions:
• Remove the support grid and burner covers with respective
crowns.
• In double burners, adjustment elements are accessible behind
the main nozzle protective plate.
• Remove the control knobs, including the gaskets.
Adaptation to a different
type of gas
Adjustment elements
16

266871
gas type, pressure Auxiliary burner Normal burner Large burner Triple burner
max min max min max min max min
Natural gas H
Wo=45,7÷54,7 MJ/ m3,
Natural gas E ,
Natural gas E+
Wo=40,9÷54,7 MJ/m3
G20,
p=20mbar
Nom. therm.
load (kW) 1 0,36 1,75 0,46 3 0,76 3,8 1,56
Consumption
(l/h) 95,21 34,4 166,62 43,8 285,64 72,4 361,8 148,5
Nozzle type
(1/100mm) 72 * 97 * 115 * 135
Nozzle code 690771 690772 690773 279803
Liquid gas 3+, 3B/P
Wo=72,9÷87,3MJ/m3
G30
p=30 mbar
Nom. therm.
load (kW) 1 0,36 1,75 0,46 3 0,76 3,8 1,56
Consumption
(l/h) 72,71 26,2 127,24 33,4 218,12 55,3 276,3 113,4
Nozzle type
(1/100mm) 50 29/24 65 33/26 85 43/33 98
Nozzle code 690780 690781 690782 279802
• Regulation valves that are factory-built-in are intended for liquid gas; however, the valves are set
for operation with the type of gas for which the appliance is factory-preset.
• When adapting the appliance for use with another type of gas, the regulation screw (valve)
should be fastened or release to correspond with the required gas flow / throughput (however,
the regulation screw should not be released more than by 1.5 rounds from the position in which it
is completely fastened).
Burner power is indicated by observing the upper Hs caloric value.
Warning: these tasks may only be carried out by a qualified technician, authorized by the
gas distributing company or authorized service center!
Gas valve
Minimum thermal load regulation valve
17
Nozzle table

WE RESERVE THE RIGHT TO MAKE ANY CHANGES THAT
DO NOT AFFECT THE FUNCTIONALITY OF THE APPLIANCE.
266871
A Serial number
B Model
C Type
D Trademark
E Code
FTechnical information
GCompliance indications / symbols
HFactory settings for gas type
18
Technical characteristics
Rating plate

PVK,KVK62S_ORA ITO en (09-12)