Gower Camden Midnight 3 Drawer Unit User manual

1 2 Assembly Instructions 3
4 5
600 and 1200 Drawer Unit Assembly
Components
Ref. No. Item Quantity Ref. No. Item Quantity Ref. No. Item Quantity Tools Required
Important Information - True Handleless Kitchens Installers: See Note Above TH
154085 6
154068 4
6
154004 6
151999
152401 4
152418 4
152402 2
5mm
Drill
Spirit Level
G-Clamp
(pair)
Medium Crosshead
Screwdriver Hammer
Tape Measure
Bradawl
Large Flathead
Screwdriver
150101 6
3.5x12mm
150202 8
4x12mm
A
A
B
C
D
154082 6
4x15mm
150201 16
150199
2
4.5x45mm
150308 2
150309 2
154047 2
151500 2
2
1
154082 6
2
6
154004
1
1 2 1 2
1 2
A
Drawer runner
98mm
1212
12
A
3.5 x 16mm x2
x4
Fit as third screw
Front 1 x 'L'; 1 x 'R'
Drawer Runner
Drawer runner
Drawer runner Drawer runner
Drawer runner
392mm
684mm
317mm
684mm
Note: Three Drawer Units Note: Two Drawer Units
3
6
154085
3
3
3
3
3
4
5
B
3
3
C
A
A
B
C
4
44
4
4
4
Caution: Some pieces of hardware could be hazardous to small children. Keep all these items out of reach and do not leave children unattended in the assembly area.
Please read these instructions carefully before proceeding. Refer to the Guide to Receiving and Installing your Kitchen booklet for further information.
Note: Due to variation in wall conditions no screws are supplied for fixing the units to the wall. If in doubt consult an expert. Assemble the unit on a clean solid work surface.
In the interest of continuing improvements we reserve the right to amend or adjust the specifications without prior notice. Errors and omissions excepted.
These units are fitted with a drawer system. The drawers are supplied separately. These instructions show the runner positions for the drawer system.
Follow the instructions supplied with the drawers for drawerbox assembly.
Every effort has been made to ensure that this product leaves the factory in perfect condition. In the unlikely event that an item is damaged or incorrect, please contact the customer services department.
Note - Fitting Handles: (1) Decide where you are going to position each handle to maintain symmetry around your kitchen. (2) Measure the handle centres and mark off each door/drawer position. (3) Drill through the door/drawer
using a fine drill (<2.5mm), then drill back from the rear face using a 4.5mm drill. (4) Attach with the fixings provided with your handle.
FM 665131
Start Locked
Do Not Over Tighten
TH Note: If fitting a “True Handleless” kitchen, some components will differ to those shown in this
instruction and will also be packaged separately. Please refer to your True Handleless guide to
Receiving for further details on the different components and difference in installation.
TH Modification required at this stage, see True
Handleless guide for further details.
TH
Modification required at this
stage, see True Handleless
guide for further details.

6 9 10 11
12 14 Installation Instructions 15 16
17 19
18 1200mm Drawer Unit 1200mm Drawer Unit
==
7
2
150199
7
45mm
9
4
9
150202
154047
2
125mm
45mm
7
7
8
9
9
8
D
6
10
4
152418
11
4
152401 150201
16
10
140mm
11
10 10
10 10
11
11
11
12
2
150202 154068
2
14
Appropriate to wall type
(Not supplied)
2
5mm
13
2
150308 150309
2
82mm
12
13 14
12
12 13
13
14
14
16
16
150101
152402
4
2
15
2
151500
15
15
15
16
16
17
4/6
151999
17
17
Note: Build and fix together two 600mm two drawer units
as shown previously. Fix drawer brackets to all four
positions on each drawer. Fittings supplied with drawers.
19
19
19
19
19
19
19
19
18
18
18
18
18
18
18
18
Ref. 170803 (04)
17
17
17
17
17
10
2
150202
154068
2
2
8
150101
125mm
8
Note: Countersunk screw
goes into back panel D.
Note: Do not over tighten screws
or use a power screwdriver.
TH
Modification
required at this
stage, see True
Handleless guide for
further details.