GPM ACADIA CHTACA4DW User manual

ACADIA 4 DRAWER CHEST
CHTACA4DW
76.5cm
39.5cm
90.3cm
90
SKU
1
395mm
765mm
903mm
GP0596
2022/0261
© CPLtd 9/2020

2

3
01
07
08
07
02
03
04
04
04
04
04
04
04
04 05
06
06
06
06
18
15
14
10
11
4x

1 1
1
1
8
1
4
2
1
4
4
4
4
4
765 X 395
664 X 115
690 X 370
335 X 115
671 X 392
300 X 25
668X 28
765 X 395
335 X 115
671 X 392
722 X 163
200 X 115
674 X 335
16
16
16
12
16
16
3
3
12
16
8
50
12
TOP
LEFT SIDE PANEL
RIGHT SIDE PANEL
BASE
LEG
DRAWER SLIDE
DRAWER FRONT
BACK PANEL
LEFT DRAWER SIDE
RIGHT DRAWER SIDE
DRAWER BOTTOM
DRAWER BACK
2
3
4
5
6
7
8
14
10
11
15
18
4
H PROFILE

GOLD
Ø4,5
16mm
P3
Ø8
25mm 28mm
25mm
Ø4,5
Ø4,5
GOLD
GOLD
P3
P3 BLACK
Ø3,5
14mm
P3
x60 x40 x06
x06 x06 x16 x08
x01
x20
5
M Y
Z
x16
x26
8x8
P3 P1
30mm 40mm
Ø3,5 Ø3,5
GOLD GOLD
P3 P3
x16
L
x16
16mm
Ø3,0
P1

02
03
A
A
A
A
A
A
A
A
A
A
A
A
E
E
E
E
E
E
Ø8
Ø8
Ø8
25mm
25mm
25mm
A
A
A
x12
x16
x16
Ex06
E
4x
4x
11
10
A
A
A
A
8x
04
A
A
BACK
BACK
Step 1
Step 2
Step 3
6

28mm
25mm
Ø4,5
Ø4,5
B
F
x18
x06
P3
P3
GOLD
GOLD
03
02
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
Build your furniture on a soft clean
cover to stop the components
getting marked during assembly.
01
02
03
F
FF
F
F
01
BACK
BACK
04
04
04
04
04
04
TOP OF PANEL
TOP OF PANEL
Ensure the drawer runner side with 2 holes for dowels
part 04 is facing towards the top of the panel.
BACK
BACK
Step 4
Step 5
7

Step 6
Step 7
Step 8
8
D
D
D
D
D
D
05
BACK
05
Dx06
40mm
Ø4,0
GOLD
P3
Ensure the drawer runner side with 2 holes for dowels
part 04 is facing towards the top of the panel.
B
B
BBB
BB
04
04
28mm
Ø4,5
Bx06
P3 GOLD
90º
TOP OF PANEL
08
07
07
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
ZZ
Z
Z
Z
Z
Z
Z
Z
Z
Z
ZZ
ZZ
Z
07
07
Zx26
8 x 8
3
90º
1
2
08

A
A
AA
A
04
04
A
A
A
A
A
A
Ø8
25mm
Ax08
FRONT
J
J
J
J
J
J
J
JJJ
J
JJ
J
J
J
J
J
J
J
06
06
06
06
J
J
J
J
J
06
180º
Jx20
GOLD
Ø4,5
16mm
P3
Step 9
Step 10
9

B
B
B
B
28mm
Ø4,5
Bx16
P3 GOLD
4x
10
14
11
A
A
Ø8
25mm
Ax08
14
14
14
14
A
8x
Fixing drawer safety stops
2.
3.
1; Insert drawers into frame
by approximately 50mm.
2; Push wooden dowels
in through the pre-drilled
holes close to the back
of the drawer sides until
they are level with the
inside edge of the
drawer sides.
3; Check the position of
the drawer stops are
correct by opening and
closing the drawers.
IMPORTANT NOTICE
Please avoid opening all drawers simultaneously
as this could cause your furniture to fall forwards.
Where there is a risk of this occurring, especially in
environments with children or uneven floors we
recommend that this item of furniture is attached to
your wall using appropriate fixings (supplied).
P3
30mm
Ø3,5
Cx16
GOLD
P3
Hx08
Gx16
BLACK
14mm14mm
Ø3,5Ø3,5
P3P3
BLACKBLACK
16mm
Ø3,0
Mx16
P1
Lx16
4x
15
G
M
GG
H
G
G
H
H
G
G
L
L
C
C
C
CM
M
18
P1
L
L
L
M
M
Step 11
Step 12
Step 13
10

Y
Y
14mm14mm
25mm
Yx01
WARNING: CHECK FOR HIDDEN PIPES AND CABLES BEFORE DRILLING.
IMPORTANT: IF YOUR WALLS ARE NOT SOLID LIKE BRICK OR STONE, YOU WILL REQUIRE SPECIALIST FITTINGS (NOT SUPPLIED).
- Place fixing strip against the wall and mark position for drilling hole.
- Drill hole in your wall to a depth of 30mm using a 6mm drill bit. If the surface of your wall is soft and crumbly, we would advise you
to use a 5mm drill bit for a tighter fit.
- Insert plug into hole with end flush to the wall surface.
- Attach fixing strip to the wall using the 25mm screw + washer and securely tighten.
- Pre-drill small pilot hole on the back edge of the furniture top using a 2mm drill bit. Attach the other end of fixing strip to the back
edge of the furniture top using the 14mm screw + washer and securely tighten.
-
.
Step 14
11