Graco The Entertainer Activity Center 4114 Owner?s User manual

234
© 1997 Graco 280-6-97
Congratulations on your purchase of a
Graco®Entertaineractivity center!
Graco is the recognized leader in the
design and manufacture of quality baby
products. We believe your new Graco®
Entertaineractivity center is a wise
choice, promising many hours of
enjoyment for your baby.
Before using your activity center, please
take a few minutes to read this Owners
Manual. The short time you spend reading
these instructions will help you to use your
activity center properly.
Customer Satisfaction
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
with Graco about your product, please contact our
Customer Service Department at 1-800-345-4109.
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use
or maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.
Model No. __________
Serial No. __________
Dear Customer,
Please fill in the
model and serial
numbers above
from the label
under the tray
of your new
Entertainer
activity center.
OWNERS
MANUAL
CARE AND MAINTENANCE
FROM TIME TO TIME CHECK YOUR ACTIVITY
CENTER for loose screws, worn parts, torn material
or stitching. Replace or repair the parts as needed.
Use only Graco®replacement parts.
REMOVABLE CLOTH SEAT may be machine
washed in lukewarm water on delicate cycle and
drip-dried. DO NOT MACHINE DRY. NO BLEACH.
TO CLEAN FRAME, use only household soap or
detergent and warm water. NO BLEACH. Use only
a damp cloth to clean the musical star.
PARTS LIST
CHECK that you have all the parts listed
below BEFORE assembling your
Entertainer activity center. If any parts
are missing, call Customer Service at
1-800-345-4109.
Tool required: Screwdriver
Model 4114
Phone and cord
Teether
toy
Beads and bar
Seat Clicker and
screw
Tray and seat ring Base
Seat lock
and screw
Steering
wheel and
wheel cap
Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THIS PRODUCT.
If you experience any difficulties, please contact the Customer Service Department.
KEEP INSTRUCTIONS FOR FUTURE USE.
THIS PRODUCT IS FOR USE ONLY by a child who is able to sit upright unassisted,
unable to walk, weighs less than 30 pounds, and is less than 32 inches tall.
EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts.
DO NOT USE THIS PRODUCT if it is damaged or broken.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
Strings can cause strangulation! DO
NOT place items with a string around
your childs neck, such as hood
strings or pacifier cords. DO NOT
suspend strings over the activity
center or attach strings to toys.
Never leave child unattended. Always
keep child in view while in this product.
Never lift or carry this product with
child in it.
Product may gradually move across
the floor as child plays in it. Watch for
movement of product and be sure
child stays away from hazards in the
area such as stairs, cords, hot liquids,
pools, sources of heat and anything
else that may injure your child.
Do not use product with a child who
can tip over or climb out of product.
To avoid tipovers, place product on
flat, level floor/ground. Adjust legs to
same height so that the tray is level
before placing child in product.
The Entertainer
Activity Center
by

Leg (3)

234
© 1997 Graco 280-6-97
Congratulations on your purchase of a
Graco®Entertaineractivity center!
Graco is the recognized leader in the
design and manufacture of quality baby
products. We believe your new Graco®
Entertaineractivity center is a wise
choice, promising many hours of
enjoyment for your baby.
Before using your activity center, please
take a few minutes to read this Owners
Manual. The short time you spend reading
these instructions will help you to use your
activity center properly.
Customer Satisfaction
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
with Graco about your product, please contact our
Customer Service Department at 1-800-345-4109.
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use
or maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.
Model No. __________
Serial No. __________
Dear Customer,
Please fill in the
model and serial
numbers above
from the label
under the tray
of your new
Entertainer
activity center.
OWNERS
MANUAL
CARE AND MAINTENANCE
FROM TIME TO TIME CHECK YOUR ACTIVITY
CENTER for loose screws, worn parts, torn material
or stitching. Replace or repair the parts as needed.
Use only Graco®replacement parts.
REMOVABLE CLOTH SEAT may be machine
washed in lukewarm water on delicate cycle and
drip-dried. DO NOT MACHINE DRY. NO BLEACH.
TO CLEAN FRAME, use only household soap or
detergent and warm water. NO BLEACH. Use only
a damp cloth to clean the musical star.
PARTS LIST
CHECK that you have all the parts listed
below BEFORE assembling your
Entertainer activity center. If any parts
are missing, call Customer Service at
1-800-345-4109.
Tool required: Screwdriver
Model 4114
Phone and cord
Teether
toy
Beads and bar
Seat Clicker and
screw
Tray and seat ring Base
Seat lock
and screw
Steering
wheel and
wheel cap
Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THIS PRODUCT.
If you experience any difficulties, please contact the Customer Service Department.
KEEP INSTRUCTIONS FOR FUTURE USE.
THIS PRODUCT IS FOR USE ONLY by a child who is able to sit upright unassisted,
unable to walk, weighs less than 30 pounds, and is less than 32 inches tall.
EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts.
DO NOT USE THIS PRODUCT if it is damaged or broken.
THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.
Strings can cause strangulation! DO
NOT place items with a string around
your childs neck, such as hood
strings or pacifier cords. DO NOT
suspend strings over the activity
center or attach strings to toys.
Never leave child unattended. Always
keep child in view while in this product.
Never lift or carry this product with
child in it.
Product may gradually move across
the floor as child plays in it. Watch for
movement of product and be sure
child stays away from hazards in the
area such as stairs, cords, hot liquids,
pools, sources of heat and anything
else that may injure your child.
Do not use product with a child who
can tip over or climb out of product.
To avoid tipovers, place product on
flat, level floor/ground. Adjust legs to
same height so that the tray is level
before placing child in product.
The Entertainer
Activity Center
by

Leg (3)

5
280-6-97 6 87
Step 9.
Assemble the toys on the tray as shown. The mirror,
squeaker, and music button are already assembled.
Tighten screw until
clicker does not
move freelyDO
NOT overtighten
then loosen screw
slightly.
Push end of phone cord
through hole in tray, then tie
a knot under the tray. Pull on
phone to make sure cord is
secure.
Insert teether
stalk into the tray.
Squeaker
Mirror and music button
DO NOT allow liquids
around music button.
Push beads firmly over the
retaining loops on bead bar.
Insert end with loops into the
hole directly over leg, and turn
bar until fully seated (retaining
loops do not go into the hole).
Then plug forked end of bar
into the square hole in the tray.
Insert
this
end
first
Push wheel cap
onto steering
wheel, then
push assembly
into large hole
in tray.
NOTE: Toys may be removed
from tray for cleaning or
storage.
Retaining
loops
Snaps visible
RIGHT WRONG
Buttons
Line
To Assemble Your
Entertainer Activity Center
Step 1.
Turn the tray over and
locate the hole that the
seat lock screws into. Place
the seat lock on the tray as
shown and screw it to the
tray. DO NOT overtighten
screwseat lock must be
free to slide.
Step 2.
Four tabs are located
behind the indentations
inside the seat ring.
Remove the seat ring by
pulling the four tabs out
from under the tray, one
at a time, while lifting the
seat ring.
Step 3.
Put the seat ring upside
down inside the cloth seat.
The high side of the seat
ring goes to the back of the
seat, where the warning
label is located.
Attach the seat to the seat
ring by tucking the seat
edge into the channel and
snapping the grommets on
the pegs.
Step 4.
Turn the seat over and
push the seat down into the
seat ring.
Step 5.
Snap the seat ring back
onto the tray. Make sure all
four tabs are snapped onto
the inside lip.
Pattern side UP
Solid color inside
Grommet
Pattern side
Step 6.
Turn tray over. Push one leg into socket in tray exactly as
shown until it snaps into place. Repeat for other two legs.
Step 7.
On top of tray, CHECK that
snaps are visible through
slots. Pull on leg to be sure it
is securely attached.
Step 8.
Slide the leg tubes on the tray onto the leg tubes on the
base as shown.
HINT: If a tray leg tube will not slide onto the base leg
tube, twist the base tube slightly to line up the parts.
Push in the buttons on each of the upper leg tubes
and adjust the activity center to the desired height.
The bottom edge of the upper tubes must be even with
one of the three lines on the lower leg tube.
CHECK that all three leg tubes are set to the same
height. To Use the Seat Lock
Push gently on latch and
turn the seat until latch
engages in one of the four
stop positions.
To allow seat to swivel
again, pull lock out.
To Adjust the Seat Height
Do not adjust height while child is in
activity center.
Step 1.
Press in the buttons on
each leg to adjust seat
to desired height. The
bottom edge of the upper
tubes must be even with
one of the three lines on
the lower leg tube.
For your childs safety, all three legs
must be set to the same height. Tray must be level.
Button
faces seat
(Note:
Squeaker
will not
work in
storage
position.)

5
280-6-97 6 87
Step 9.
Assemble the toys on the tray as shown. The mirror,
squeaker, and music button are already assembled.
Tighten screw until
clicker does not
move freelyDO
NOT overtighten
then loosen screw
slightly.
Push end of phone cord
through hole in tray, then tie
a knot under the tray. Pull on
phone to make sure cord is
secure.
Insert teether
stalk into the tray.
Squeaker
Mirror and music button
DO NOT allow liquids
around music button.
Push beads firmly over the
retaining loops on bead bar.
Insert end with loops into the
hole directly over leg, and turn
bar until fully seated (retaining
loops do not go into the hole).
Then plug forked end of bar
into the square hole in the tray.
Insert
this
end
first
Push wheel cap
onto steering
wheel, then
push assembly
into large hole
in tray.
NOTE: Toys may be removed
from tray for cleaning or
storage.
Retaining
loops
Snaps visible
RIGHT WRONG
Buttons
Line
To Assemble Your
Entertainer Activity Center
Step 1.
Turn the tray over and
locate the hole that the
seat lock screws into. Place
the seat lock on the tray as
shown and screw it to the
tray. DO NOT overtighten
screwseat lock must be
free to slide.
Step 2.
Four tabs are located
behind the indentations
inside the seat ring.
Remove the seat ring by
pulling the four tabs out
from under the tray, one
at a time, while lifting the
seat ring.
Step 3.
Put the seat ring upside
down inside the cloth seat.
The high side of the seat
ring goes to the back of the
seat, where the warning
label is located.
Attach the seat to the seat
ring by tucking the seat
edge into the channel and
snapping the grommets on
the pegs.
Step 4.
Turn the seat over and
push the seat down into the
seat ring.
Step 5.
Snap the seat ring back
onto the tray. Make sure all
four tabs are snapped onto
the inside lip.
Pattern side UP
Solid color inside
Grommet
Pattern side
Step 6.
Turn tray over. Push one leg into socket in tray exactly as
shown until it snaps into place. Repeat for other two legs.
Step 7.
On top of tray, CHECK that
snaps are visible through
slots. Pull on leg to be sure it
is securely attached.
Step 8.
Slide the leg tubes on the tray onto the leg tubes on the
base as shown.
HINT: If a tray leg tube will not slide onto the base leg
tube, twist the base tube slightly to line up the parts.
Push in the buttons on each of the upper leg tubes
and adjust the activity center to the desired height.
The bottom edge of the upper tubes must be even with
one of the three lines on the lower leg tube.
CHECK that all three leg tubes are set to the same
height. To Use the Seat Lock
Push gently on latch and
turn the seat until latch
engages in one of the four
stop positions.
To allow seat to swivel
again, pull lock out.
To Adjust the Seat Height
Do not adjust height while child is in
activity center.
Step 1.
Press in the buttons on
each leg to adjust seat
to desired height. The
bottom edge of the upper
tubes must be even with
one of the three lines on
the lower leg tube.
For your childs safety, all three legs
must be set to the same height. Tray must be level.
Button
faces seat
(Note:
Squeaker
will not
work in
storage
position.)

9
280-6-97 10
Tray at proper height
Step 2.
After adjusting height of the seat, CHECK that your
childs feet can rest completely on the floor of your
activity center. Tray should not be too high or too low.
Remove child and readjust height if necessary.
Replacement Parts
Instructions for ordering activity center parts:
Complete form below. Your model number MUST be
included on the form to ensure proper replacement parts.
Your model number can be found on a sticker on the bottom
of the tray. Payment must accompany your order.
Return the form below with payment to:
GRACO CHILDRENS PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
MAIN STREET
ELVERSON, PA 19520
IF YOU NEED HELP
If you have any questions, please call toll-free:
1-800-345-4109
Model Number
(Must be filled in)
SHIP TO:
Name
Address
City, State, Zip
( )
Telephone
Total:
6% sales tax
(PA only):
Total amount
due:
Check enclosed
(payable to Graco Childrens
Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Account #:
Expiration date:
Signature:
Mirror
Musical star
Teether toy
Squeaker and button
Beads and loop
Phone and cord
Clicker and screw
Wheel and cap
Cloth seat
Seat ring and bearings
Seat lock and screw
Complete tray unit
Height buttons and
springs
Retainer rings
Spring covers with
retainer rings
Complete base unit
Parts List:
Mirror .............................................................
Musical star ....................................................
Teether toy ....................................................
Squeaker and button ....................................
Beads and loop ..............................................
Phone and cord .............................................
Clicker and screw .........................................
Wheel and cap ..............................................
Cloth seat ......................................................
Seat ring and bearings ..................................
Seat lock and screw ......................................
Complete tray unit (with legs, height .............
springs and height buttons)
Height buttons and height springs only ........
Retainer rings ................................................
Spring covers with retainer rings ..................
Complete base unit (with legs, retainer ........
straps, spring covers, and retainer rings)
Price:*
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 5.00
$ 14.50
$ 7.00
$ 5.00
$ 25.00
$ 5.00
$ 5.00
$ 5.00
$ 20.00
* Prices subject to change
without notice.
TRAY TOO HIGH TRAY TOO LOW