Graco True Focus 2V00 User manual

True Focus
OWNER’S MANUAL
©2010 Graco PD141639A 5/10 US
Model 2V00
Keep Instructions For Future Reference

2
Failure to follow these warnings and the assembly
instructions could result in serious injury or death.
This device is designed to aid in the monitoring of
your child. When using the monitor, you must still
provide the supervision necessary for the continued
safety of your child. This product is not designed or
intended for use as a medical monitor. Always be sure
that both the transmitter and receiver are working
properly and are within range of each other.
• STRANGULATION HAZARD. Keep the adapter
cords out of the reach of children. Do not use with
extension cords.
• DO NOT place the Nursery Unit or its cord within
your child’s reach. Do not put the Nursery Unit inside a
crib or playard.
• Use ONLY with 110-120 volt AC electrical outlets.
• Protect the AC adapter cords. Place them so they are
not walked on or pinched by furniture or other items.
• Allow for proper ventilation when units are in use.
Do not cover the Nursery Unit or Parent Units with any
object such as a blanket. Do not place it in a drawer or in
any location which would mufe the sound or interfere
with the normal ow of air.
• DO NOT immerse any part of the Nursery Unit or
Parent Units in water. Clean only with a dry cloth.
Warnings to Parents and Other Users

3
• DO NOT place unit near water and moisture. Do not
use the Nursery Unit outdoors. Do not use the Nursery
Unit near possible wet areas, such as a bathtub, shower,
wash basin, sink, laundry tub, swimming pool, wet
basement, etc.
• Keep Nursery Unit away from heat sources, such as
replaces, radiators, stoves, and TVs or other appliances.
Heat can damage the case or electrical parts.
• Do not use the Nursery Unit if:
• The adapter cords or plugs have been damaged.
• The unit has been exposed to liquids.
• Unit has been dropped or is damaged.
• DO NOT OPEN THE NURSERY UNIT, PARENT
UNIT, OR ADAPTERS. No user-serviceable parts
inside. Risk of electrical shock, re or death.
• The antenna used for this transmitter must be installed
to provide a separation distance of at least 20 cm (7.9”)
from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter.
FCC Statement:
WARNING Modications not authorized by the
manufacturer may void users authority to operate this
device.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.

4
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
• Look for the FCC ID on the back of the Nursery Unit
and inside the battery compartment on the Parent Unit.

5
Parts List
Adult assembly required.
Tool required: Phillips screwdriver
Nursery Unit
(PD141481)
(1) AC Adapter
(1) AC Adapter
Parent Unit
(PD141402)
(1) Parent Unit
Battery

6
Parent Unit
DC Adapter
Jack
Belt Clip
Battery Compartment
SoundLights
Volume Up/Down
Power Zoom Out
Zoom
In
Menu
Navigation
buttons
Signal Strength
Indicator
Battery Status
Indicator

7
Installing Batteries
• The battery must be
plugged into the Parent Unit
before the unit will be ready
for use.
Use a Phillips head
screwdriver to remove the
battery door.
NOTE: Screw should be
loosened but stay attached to
battery door.
Remove the battery pack
from the packaging and plug
into the back of the unit.
Place the battery pack into
the recess and press the wire
into the slot on the side.
2
1

8
Replace the battery door.
• The Parent Unit(s) uses a rechargeable battery pack
or standard 120 volt AC household current. To use
AC adapters, plug the connector on the cord into the
DC adapter jack on the side of the Parent Unit. Then
plug adapter into a standard wall outlet.
• Use ONLY the Graco adapters included with the
unit. Do not use these adapters with other equipment
under any circumstances.
• If units do not work, check that AC adapters are
plugged into working outlets.
Using AC Adapters
3
4

9
Nursery Unit
DC Adapter
Jack
Battery Compartment
Power
Camera

10
Battery Installation
Use a Phillips head
screwdriver to remove the
battery door.
NOTE: Screw should be
loosened but stay attached
to battery door.
Insert 3-AA (1.5V-LR03)
batteries.
Make sure they are
inserted correctly.
• Batteries will power the Nursery Unit in the event of
a power outage. Only audio (no video) is operational
when running on battery power.
• Batteries should be replaced periodically.
5
6

11
Replace the battery door.
● The Nursery Unit uses 3-AA
(1.5V-LR03) batteries or standard
120 volt AC household current.
● To use AC adapters, plug the
connector on the cord into the AC
adapter jack on the back of the
Nursery Unit. Then plug adapter
into a standard wall outlet.
● Use ONLY the Graco adapters included with the unit.
Do not use these adapters with other equipment under
any circumstances.
● If units do not work, check that AC adapters are
plugged into working outlets.
● When electricity is off (from a power failure, etc.), the
Nursery Unit will operate on 3-AA (1.5V-LR03)
batteries in audio mode only.
8
7
Using AC Adapters

12
Static Cling Labels
Remove and discard static
cling labels.
9

13
Within a few seconds, the
Parent Unit will lock on to the
Nursery Unit.
A second later, you will hear a
series of beeps and the
connection light will turn
on. Your monitor is now ready
for use.
12
Setting Up the Baby Monitor
NOTE: It is very important that the steps below be
followed for first time power-up.
● Place the Nursery Unit within 10 feet (3 meters) of your
baby. Plug an AC adapter into the jack on the back of the
Nursery Unit. Plug it into a working 120 volt AC outlet.
● Point the Nursery Unit toward your baby.
11
Place the Parent Unit within five
(5) feet (1.5 meters) of the
Nursery Unit and turn on the
Parent Unit using the On/Off
button on right side of the LCD
screen.
Depress button for 1 sec. to turn
camera on.
10

14
Testing the System
It is VERY IMPORTANT to test the system when first
set up, and at regular times thereafter. Test the units
if you suspect they may have been damaged or have not
been used for a long time.
1. If two adults are present, have one take the Parent
Units to different locations, trying various volume
settings, while the other speaks into the Nursery Unit.
2. If only one adult is available, place a ticking clock,
radio, or other sound-producing device near the Nursery
Unit to test it.
3. When testing, keep the level of your child’s sounds in
mind, and adjust the volume accordingly.
4. If there is sound interference, try moving the child unit
to a different location.
Cam 1: Lost Signal
Cam 1: Detected
When a new baby unit is
detected, the “Camera
Detected” message
displays on the screen of
the Parent Unit. The
video feed does not
change.
The message fades away
after 3 seconds.
13

1515
Depress button for 1 sec.
to turn camera on.
To change camera angle,
swivel the nursery unit in
the desired direction.
15
Nursery Unit Power On/Off
14
16
15

16
Parent Unit Power On/Off
17 Press and hold ON/OFF
button for 1 second. Unit
will cycle through intro
and begin searching for
the Nursery Unit.
Make sure Nursery Unit
is turned on. The parent
unit will display the
Graco logo on the status
screen until the nursery
unit is found. The live
video feed will then be
shown.
The connection LED
will turn from red to
green.
18

17
19 Press and hold ON/OFF
button for 1 second to
turn unit off.
To activate or deactivate
the live video feed, press
the video button.
20
Pressing the video but-
ton will allow the user
to view the image from
the nursery unit.

18
To cycle through the
different choices, press up
or down.
After choosing one of the
options, press the “MENU”
button to make the
selection.
NOTE: Once you make a selection (MENU), the unit
will automatically advance you to the next option/screen
or return you to the live video feed (if applicable).
To set up preferences or
change status, press the
“MENU” button.
22
21
23

19
Zoom
The zoom indicator
appears on the screen
to indicate the current
zoom level. This
indicator disappears after
a 2 second timeout.
2x
2x
2x
2x
26
24 Press button to
Zoom In on baby.
Zooms in on the center of
the video feed one level.
The zoom levels are 1x
and 2x.
2x
25 Press button to
Zoom In on baby.
Zooms out on the center
of the video feed one
level.
The zoom levels are 1x
and 2x.
2x

20
Brightness
The brightness for the
LCD ranges from 0% to
100%, in 10%
increments.
The default value is 50%.
Contrast
Screen Timeout
Brightness 50%
50%
Off
Camera Cam 1
Language English
Contrast
Screen Timeout
Brightness 50%
50%
Off
Camera Cam 1
Language English
Press Menu to Exit
Press Menu to Exit
27
To return to live Video feed (if available) select and
press: MENU or wait 5 seconds and monitor will
return to live video view on it’s own.
28 Decreases the
brightness level by 10%.
If the brightness level
is 0%, then it wraps to
100%.
29 Increases the
brightness level by 10%.
If the brightness level is
100%, then it wraps to
0%.