Graco 17G554 User manual

3A3112E
EN
Instructions
ToughTek™F340e Remote Switch
Accessory Kit
For controlling power to the F340e at the applicator. For professional use only.
Not approved for use in explosive atmospheres or hazardous (classified) locations.
Model 17G554
Important Safety Instructions
Read all warnings and instructions in this manual and
the ToughTek™F340e manual before using this
equipment. Save these instructions.





WLF



Ref. Part Description Qty.
1 - - - - - ENCLOSURE, remote switch 1
3 114421 BUSHING, strain relief 2
4 113161 SCREW, flange, hex hd 2
5 128597 GROMMET, 3/16 in. ID x 9/16 in.
OD
1
6 128596 GROMMET, 5/16 in. ID x 1 in. OD 1
7 125871 TIE, cable, 7.5 in. 1
9 17F719 SWITCH, rotary 1
11 18B211 HARNESS 1
12 18B225 CONNECTOR, circular,4 pin, plug 1

Instructions
23A3112E
Instructions
1. Turn off and disconnect power cord.
2. Slip the strain relief bushing nut (3) over the cable.
3. Route cable through the hole in the cart side plate
(located near the control box).
4. Slip the strain relief bushing (3) over the cable from
the other side of the cart side plate. Thread the
strain relief nut (3) onto the bushing until tight.
5. Tighten the strain relief bushing (3) to the cable until
snug.
NOTE: Leave two inches of cable between the remote
enclosure (1) and strain relief nut (3).
6. Install the remote enclosure (1) to the cart side plate
and tighten the mounting screws (4).
7. Route the cable through the hole in the cart top
plate.
8. Slip the large grommet (6) over the cable and insert
the grommet into the hole on the top plate.
9. Open the motor control box and remove the yellow
jumper wire and connector (Z) in J6 by pinching the
tab on the bottom.
NOTE: It may be easier to first disconnect the connector
below to allow more room to grab it.
10. Remove the plug (P), then route the cable into the
motor control box.
11. Plug the remote switch cable to the same J6
connector that was just unplugged. Re-insert the
connector below if it was removed in step 9.
12. Cut the small grommet (5) to fit over the cable and
push it into the hole from where plug (P) was
removed.
13. Make sure there is some slack on the cable inside
the motor control, then attach the cable tie (7) next
to the grommet to provide additional strain relief.
14. Clip and remove excess cable tie (7).
15. Close the motor control module and screw shut.
16. Install remote switch cable (2) into enclosure
connector (1).
WARNING
ELECTRIC SHOCK HAZARD
The equipment must be grounded. Improper
grounding, setup, or usage of the system can cause
electric shock.
• Turn off and disconnect power cord before
servicing equipment.
• Connect only to grounded electrical outlets.
-

Instructions
3A3112E 3
Routing Diagram

WLE





3
.
6
;
<=



-

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A3112
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2019, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision E, October 2019
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: [phone] or Toll Free: 1-800-328-0211 Fax: [phone]