GrandEye GE-P8001-UT User manual
Shop No. 338/1, G.M. Complex, Ganthipuram Sixth St,
www.grandeye.net
GE-P8001-UT
GE-P8001-UT
8 Ports PoE Switch
8 PORTS POE SWITCH
8 ports PoE Switch is a security surveillance Ethernet Switch which aims at Ethernet high definition surveillance and Ethernet project
security system. The product fully combines the characteristics of security surveillance, provides fast packet forwarding ability and
abundant backplane bandwidth, which ensures clear image and fluent transmission. Inserted static, surge protection circuit can improve
product stability. The product supports one key CCTV model, can achieve VLAN, QoS priority after configuration, control the Net storm,
protect the information security, prevent the viral transmission and Ethernet attack, fully satisfy the Ethernet video security surveillance
system and Ethernet project needs.
Major ports: 1pc 100Mbps uplink Ethernet port, 8 pcs100Mbps
downlink Ethernet every port supports MDI/MDIX;
One key CCTV mode; 1~8 downlink ports can only communicate
with uplink ports; Restrain network storm under 3Mbps;Extend
downlink ports transmission distance to 250m;
Power input: DC48V~57V; Standard: Meet IEEE802.3 , IEEE802.3u,
IEEE802.3 af/at standards,PoE use End-Span, the spare cable can be
of other use Protection: Excellent anti-thunder, anti-static and anti-
interference ability;
Appearance: Delicate design and easy installation, configure the
anti-theft lock hole, Operation: Plug and Play, No Setting required.
GE-P8001-UT 8Ports PoE Switch
Introduction
Specification Feature
Board Diagram
Item
Packet Forwarding Rate
PoE Power Supply
Exchange Type
1.34Mpps
1/2(+), 3/6(-)
MAC Address List
ESD Protection
Buffer
PoE Standard
Voltage Input
Storage&Fowarding
2K
Contact discharge 6K, Air discharge 8KV, Per: IEC61000-4-2
768k
DC 48V~57V
Description
Power Consumption 5W
Operation Temperature
Characteristics
Installation steps
Please check the following items before installation, if it is missing,
please contact the dealer.
8 ports PoE Ethernet Switch 1pc
Power adaptor 1pc
AC Power Cable 1pc
Accessories 1pc
User Manual 1pc
Please follow installation s teps as below:
Please turn off the signal power and display device power before
installation, installation with power will damage the transmission
equipment;
Use network cable connect PoE IP camera and 1～8 downlink ports
of product respectively;
Use a network cable connect equipment uplink port and NVR or
computer; Connect power adapter;
Check if the installation is correct, equipment is in good condition,
the connection is stable, then provide power for system;
Ensure the Ethernet equipment with power and work properly.
Downlink Ports 8x10/100Base-TX (PoE)
Uplink Ports 1x 10/100Base-TX
Network Standard IEEE 802.3/802.3u/IEEE802.3x
Switch Capacity 1.8Gbps
802.3af/at(PSE)
PoE Output
CCTV Mode
Surge Immunity
Single PoE Output≤30W(54V DC), Whole machine PoE out-
1. Downlink ports only communicate with uplink ports
2.Extend transmission distance to 250m(Downlink Ports)
3.Rate:10Mbps(Downlink Ports)
6KV : IEC61000-4-5
-10c~+55c
Storage Temperature
Operation Humidity
-40c~+85c
5%-95%(Non-condensing)
Dimensions(LxWxH)
Material
Weight
200mm×101.8mm×27mm
Metal
500g
Application
GE-P8001-UT
PoE Standard
PoE Mode
802.3af/at(PSE)
End-span
Front Board Back Board Side Board
3Web design & development for ActiveXplore
Characteristics
Please folloe these step if the equipment have trouble.
Make sure the equipment is installed according to the manufactures installation guide.
Confirm RJ45 cable order meet EIA/TIA568A or 568B standard.
Every PoE port can provide PoE equipment maximum power less than 30W, please do not connect the PoE equipment with power over 30W.
Replace the equipment that can not work with a proper functioning 8port PoE Ethernet switch to check if the equipment is damaged.
Please contact your vendor if trouble still exists.
GE-P8001-UT 8 Ports PoE Switch
Troubleshoot
Plug Producing Method
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should conform with
EIA/TIA568A or 568B.
Please remove 2cm long the insulating layer, and bare 4 pairs UTP cable;
Separate the 4 pairs UTP cable and straighten them;
Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
Cut out 1.5 cm cable wrap and leave the bare wire;
Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
Then use wire crimper to crimp it;
Repeat above 5 steps to make the another end;
Using network tester to test the cable if it works.
Other GrandEye Switch manuals
