Grandstream Networks UCM6100 Series Assembly instructions

Grandstream Networks, Inc.
UCM6100 Security Manual

UCM6100 Security Manual Page 1 of 23
Index
Table of Contents
OVERVIEW ................................................................................................3
WEB UI ACCESS.......................................................................................4
UCM6100 HTTP SERVER ACCESS.....................................................................................................4
PROTOCOL TYPE.................................................................................................................................4
USER LOGIN.........................................................................................................................................4
LOGIN TIMEOUT...................................................................................................................................5
TWO-LEVEL USER MANAGEMENT ....................................................................................................5
EXTENSION SECURITY............................................................................7
SIP/IAX PASSWORD.............................................................................................................................7
STRATEGY OF IP ACCESS CONTROL ...............................................................................................7
EXAMPLE: LOCAL SUBNET ONLY...............................................................................................7
SRTP....................................................................................................................................................10
TRUNK SECURITY..................................................................................11
OUTBOUND RULE PERMISSIONS....................................................................................................11
PRIVILEGE LEVEL....................................................................................................................... 11
SOURCE CALLER ID FILTER .....................................................................................................12
IVR DIAL TRUNK.................................................................................................................................12
ALLOW GUEST CALLS.......................................................................................................................13
TLS...........................................................................................................14
FIREWALL ...............................................................................................16
STATIC DEFENSE...............................................................................................................................16
STATIC DEFENSE EXAMPLE: BLOCKING TCP CONNECTION FROM A SPECIFIC HOST....17
STATIC DEFENSE EXAMPLE: BLOCKING SSH CONNECTION TO UCM6100........................18
DYNAMIC DEFENSE ..........................................................................................................................20
FAIL2BAN ............................................................................................................................................20
AMI...........................................................................................................23

UCM6100 Security Manual Page 2 of 23
Table of Figures
Figure 1: UCM6102 Web UI Login................................................................................................................4
Figure 2: Strategy –Local Subnet Only........................................................................................................8
Figure 3: Registration Failed From Subnet Not Allowed For Registration....................................................9
Figure 4: Registration Successful From Allowed Subnet..............................................................................9
Figure 5: Outbound Rule Permissions........................................................................................................11
Figure 6: Source Caller ID Filter .................................................................................................................12
Figure 7: IVR Dial Trunk..............................................................................................................................13
Figure 8: PBX->SIP Settings->TCP/TLS ....................................................................................................14
Figure 9: Firewall Rule Custom Configuration............................................................................................17
Figure 10: Static Defense Blocking Host 192.168.40.142 Using TCP Connection.....................................17
Figure 11: Host blocked by UCM6100 ........................................................................................................18
Figure 12: UCM6100 SSH Access..............................................................................................................18
Figure 13: Block SSH Connection ..............................................................................................................19
Figure 14: Putty Setup for SSH Connection ...............................................................................................19
Figure 15: SSH Connection Blocked by UCM6100 ....................................................................................20
Figure 16: Fail2Ban Default Configuration..................................................................................................21
Figure 17: Asterisk Service Fail2Ban setting ..............................................................................................22
This document is subject to change without notice. The latest electronic version of this document is
available for download here:
http://www.grandstream.com/support
Reproduction or transmittal of the entire or any part, in any form or by any means, electronic or print, for
any purpose without the express written permission of Grandstream Networks, Inc. is not permitted.

UCM6100 Security Manual Page 3 of 23
OVERVIEW
This document presents a summary of security concerns on UCM6100. It covers the security risks and
related configurations that users need to consider when deploying the UCM6100.
The following sections are covered in this document:
Web UI access
Web UI is secured by user login and login timeout mechanism. Two-level user management is
configurable. Admin with limited access can be created by the default super administrator.
Extension security
This includes SIP/IAX password for authentication, IP access control and SRTP.
Trunk security
Trunk security is achieved mainly by setting the privilege level, configuring source caller ID filter to filter
out outbound call requests from unwanted source
TLS
This is to secure the SIP signaling.
Firewall mechanism
Three types of firewall mechanism can be configured to protect UCM6100 against malicious attacks:
Static Defense, Dynamic Defense (UCM6510 and UCM6102 only) and Fail2ban.
AMI
Using AMI feature comes with security concerns for UCM6100 administrators to consider.

UCM6100 Security Manual Page 4 of 23
WEB UI ACCESS
UCM6100 HTTP SERVER ACCESS
The UCM6100 embedded web server responds to HTTP/HTTPS GET/POST requests. Embedded HTML
pages allow users to configure the device through a web browser such as Microsoft IE, Mozilla Firefox,
Google Chrome and etc. This is the most important tool to configure all the settings on the UCM6100. It’s
also the immediate interface for the administrator to access configurations, user status and all the system
information. Therefore, it’s crucial to understand that directly placing the UCM6100 on public network could
expose the domain name / IP address of the UCM6100 and pose serious security concerns.
PROTOCOL TYPE
HTTP and HTTPS (default) are supported to access the UCM6100 web UI. It can be configured under web
UI->Settings->HTTP Server. The protocol type is also the protocol used for zero config when the endpoint
device downloads the config file from the UCM6100. Therefore, it’s recommended to use HTTPS instead
of HTTP to secure the transactions and prevent unauthorized access.
USER LOGIN
UCM6100 web UI access is restricted by user login. Username and password are required when logging in
to web UI.
Figure 1: UCM6102 Web UI Login
The factory default value of “Username” and “Password” is “admin” and “admin”. It is highly recommended

UCM6100 Security Manual Page 5 of 23
to change the default password after login for the first time.
To change the password for the default user “admin”, go to web GUI->Settings->Change Password page.
The new password has to be at least 4 characters. The maximum length of the password is 30 characters.
The minimum requirement for the login password is as below if “Enable Strong Password” (on web GUI->
PBX->Internal Options->General) is turned on:
Must contain numeric digit;
Must contain at least one lowercase alphabet, uppercase alphabet or special character.
Strong password with a combination of numbers, lowercase alphabet characters, uppercase characters
and special characters is always recommended to protect your login.
LOGIN TIMEOUT
An authenticated user of the UCM6100 web UI may log in the system and then leave the active session on
a terminal unattended without intentionally logging-off from the system. An adversary with access to the
terminal could then have access to the UCM6100, meaning all the configuration and status information
could be exposed and changed intentionally or unintentionally.
UCM6100 provides protection from such vulnerability using login timeout. After the user logs in the
UCM6100 web UI, the user will be automatically logged out after certain timeout. This timeout value can be
specified under UCM100 web GUI->Settings->Login Timeout Settings page. In the case that the user
doesn’t make any operation on web GUI within the timeout period, the user will be logged out automatically
and the web UI will be redirected to the login page, requiring password to access the web pages.
If the login timeout period is set to a short enough time, the chances of an adversary gaining access to an
unattended terminal are significantly reduced. However, the timeout period cannot be too short that an
authenticated user becomes annoyed by frequent automatic logouts during normal use. Therefore, users
shall set it to a value according to actual usage and situation. The default value of login timeout is 10
minutes.
TWO-LEVEL USER MANAGEMENT
On UCM6100, two privilege levels for web UI users are supported:
Super Admin: high priority
Admin: low priority
Super administrator can access all pages on UCM6100 web UI, change configuration for all options and

UCM6100 Security Manual Page 6 of 23
execute all the operations, while normal administrator created by super administrator has limited access.
Normal administrator can access all pages on UCM6100 web UI except the following:
Maintenance->Upgrade
Maintenance->Backup
Maintenance->Cleaner
Maintenance->Reset/Reboot
Settings->User Management->Operation Log
A “Super Admin” user with username “admin” is innately configured in the UCM6100 at the factory setting.
It is the only allowed “Super Admin” account and cannot be deleted and changed. This super administrator
could create, edit and delete new user accounts with lower privilege “Admin”.
Super Admin also has the authority to view operations done by all the users in web GUI->Settings->User
Management->Operation Log where normal users with lower privilege level “Admin” don’t have access.
If there are more than one PBX administrator required to manage the UCM6100 in your enterprise, it’s
highly recommended for the super administrator to create lower privilege administrators in order to
manage the UCM6100 together, instead of handing out super administrator password to all the other users
who may need access the UCM6100 web UI. The super administrator can also monitor the operation log
to keep a record as well as ensure no abnormal operations done on the PBX.

UCM6100 Security Manual Page 7 of 23
EXTENSION SECURITY
SIP/IAX PASSWORD
When creating a new SIP/IAX extension, the UCM6100 administrator is required to configure “SIP/IAX
Password” which will be used for account registration authentication.
If “Enable Random Password” (on web GUI->PBX->Internal Options->General) is enabled, “SIP/IAX
Password” is automatically filled with a randomly generated secure password when creating the extension
on the UCM6100.
If “Enable Strong Password” (on web GUI-> PBX->Internal Options->General) is enabled, the password
must be alphanumeric which should contain numeric digit and at least one lower case alphabet or upper
case alphabet, or special character.
It is recommended to use random password and strong password to reduce the chance that the password
being guessed or cracked out.
STRATEGY OF IP ACCESS CONTROL
The UCM6100 administrator could control what IP address(s) is allowed to register to a certain extension
by editing “strategy” option under extension configuration dialog->“Media” tag. Make sure to configure the
“strategy” option to the smallest set to block registration attempts from anyone that doesn’t need to register
to the account.
The strategy options are:
“Local Subnet Only”: allows register requests from local IPs only. By default the local subnet where the
UCM6100 is location is allowed. User could also add more local subnets where devices are allowed to
register to this extension.
“A Specific IP Address”: allows register requests from one user specified IP only.
“Allow All”: the registration address is the entire Internet which is least recommended.
EXAMPLE: LOCAL SUBNET ONLY
1. Assuming there are multiple subnets within the office and the devices in all subnets can reach each

UCM6100 Security Manual Page 8 of 23
other. The network administrator would like to allow only devices in 192.168.40.x network to register to
this UCM6100.
2. Under UCM6100 web UI extension dialog, configure “Local Subnet Only” for “Strategy” option and
192.168.40.0 for “Local Subnet”.
Figure 2: Strategy –Local Subnet Only
3. Save and Apply changes.
Now if the SIP end device is in subnet other than 192.168.40.x, e.g., 172.18.31.x subnet, the UCM6100
will not allow registration using this extension. The following figure shows the SIP device IP address is
172.18.31.17. The UCM6100 on IP 192.168.40.171 replies 404 Not Found for the registration request.

UCM6100 Security Manual Page 9 of 23
Figure 3: Registration Failed From Subnet Not Allowed For Registration
Once moving this device to 192.168.40.x subnet, registration will be successful. The following figure shows
the IP address for the same SIP end device is 192.168.40.190. The UCM6100 on IP address
192.168.40.171 replies 200 OK for the registration request.
Figure 4: Registration Successful From Allowed Subnet

UCM6100 Security Manual Page 10 of 23
SRTP
SRTP is supported on UCM6100 to secure RTP during the call. By default it’s disabled. To use it, please
configure under extension configuration dialog->“Media” tag when creating/editing an extension. If SRTP is
enabled, RTP data flow will be encrypted.

UCM6100 Security Manual Page 11 of 23
TRUNK SECURITY
A potential risk for trunks is that unwanted users may gain the authority to make international or long
distance calls. This will result in unexpected high charges before the UCM6100 administrator notices this.
Usually this high cost is due to improper configurations on the UCM6100. Therefore administrators must
be extremely cautious when configuring those trunks that will be charged by placing certain calls, for
example, PSTN trunks or SIP trunks with international call capability.
OUTBOUND RULE PERMISSIONS
Two methods are supported on UCM6100 to control outbound rule permissions and users can apply one of
them to the outbound rule.
1. Privilege Level
2. Enable Filter on Source Caller ID
Please make sure to configure it to allow only the desired group of users to call from this route.
Figure 5: Outbound Rule Permissions
PRIVILEGE LEVEL
On the UCM6100, the supported 4 privilege levels are “Internal”, “Local”, “National” and “International”
from the lowest to the highest. Outbound calls through trunk can be placed only if the privilege of the caller
is higher or equal to the privilege of the outbound rule. Outbound call requests from users with privilege

UCM6100 Security Manual Page 12 of 23
lower than the outbound rule will be rejected. Please configure the privilege for the outbound rule high
enough to restrict the extensions allowed to call external numbers via this trunk.
SOURCE CALLER ID FILTER
Instead of using privilege level, UCM6100 administrator could specify the extensions/extension groups that
are allowed to use the outbound rule. This can be done by selecting extension/extension groups or
defining pattern for the source caller ID in “Custom Dynamic Route” field. The extension allowed to make
outbound call will either need to be an extension in the selected list or match the defined pattern.
Figure 6: Source Caller ID Filter
Please specify the extension or the pattern here to the minimal set so that only the desired users can dial
out from this outbound route.
For detailed configuration instructions, please refer to MANAGING OUTBOUND ROUTE section in white
paper: How to manage inbound/outbound route on UCM6510/6100
IVR DIAL TRUNK
When creating/editing an IVR, the administrator could decide whether to allow the calls entering the IVR to
make outbound calls through trunks by configuring “Dial Trunk” and “Permission”. If “Dial Trunk” option is
enabled, the caller calling into the IVR will be able to dial external numbers through a trunk if the IVR’S
permission is higher than or equal to the privilege of the trunk. The potential risk here is that unwanted
users may call into IVR and then dial external number. This could possibly generate expected high charges
especially if an IVR is configured as the destination of an inbound route of a PSTN trunk, in which case,
anyone can call into the IVR and then dial out to long distance or international calls.

UCM6100 Security Manual Page 13 of 23
Figure 7: IVR Dial Trunk
We recommend to disable “Dial Trunk” option unless the risk associated with it is clearly understood or the
PBX administrator intentionally configures it to do so for specific reasons. If it has to be enabled, please
configure the “permission” as secure as possible to restrict the authorized callers to be known users.
For more information about IVR permissions, please refer to IVR PERMISSION section in white paper:
How to manage inbound/outbound route on UCM6510/6100
ALLOW GUEST CALLS
“Allow Guest Calls” option can be found on web GUI->PBX->SIP Settings->General page. We highly
recommend NOT to turn on this option for any deployments. Enabling “Allow Guest Calls” will stop the
PBX from authenticating incoming calls from unknown or anonymous callers. In that case, hackers get the
chance to send INVITE to UCM6100 and the UCM6100 will place the call without authentication. This can
result in high toll charges. The administrator might also want to check CDR regularly to make sure there is
no suspicious calls in the early stage of deployment.

UCM6100 Security Manual Page 14 of 23
TLS
The UCM6100 administrators may consider securing SIP packets sent across an untrusted network. Using
TLS could be a solution. It will authenticate servers and clients, and then encrypt SIP messages between
the authenticated parties.
TLS can be configured under UCM6100 web GUI->PBX->SIP Settings->TCP/TLS page.
Figure 8: PBX->SIP Settings->TCP/TLS
1. Set “TLS Enable” as “Yes” to enable TLS on UCM6100.
2. Configure “TLS Do Not Verify”, “TLS Self-Signed CA” and “TLS Cert” properly to achieve basic TLS
authentication and encryption.
TLS Self-Signed CA
This is used when UCM6100 acts as a client, to authenticate the server. If the server the
UCM6100 connecting to uses a self-signed certificate, you should have their certificate installed

UCM6100 Security Manual Page 15 of 23
here so authenticity of their certificate can be verified. If the server uses a certificate that is signed
by one of the larger CAs, you should install a copy of server CA certificate here.
TLS Cert
This is used when UCM6100 acts as a server. It’s sent to the client during TLS handshake. The
TLS Cert should include the key and server certificate. The “common name” field in the server
certificate should match the server host (either IP or domain name). This is required if the client
side is another UCM6100 (not a standard, some clients do not have this requirement for server
authentication). If not matching, authentication on the UCM6100 (client) fails and the TLS
connection cannot get established.
TLS Do Not Verify
This is effective when UCM6100 acts as a client. If set to “Yes”, the server’s certificate (sent to the
client during TLS Handshake) won’t be verified. Considering if two UCM6100s are peered, since
the default certificate built in UCM6100 at the factory has “common name” equaling “localhost”
which is not a valid IP address, authentication will fail for sure. So this is the default setting to avoid
authentication failure when using default certificate. Please note skipping verification won’t have
effect on encrypting SIP messages. If set to “No”, UCM6100 (client) will verify the server’s
certificate using “TLS Self-Signed CA”.
Please note that administrator also needs configure “SIP Transport” to be “TLS” on the SIP endpoint
device to encrypt SIP messages sent to the UCM6100.

UCM6100 Security Manual Page 16 of 23
FIREWALL
The firewall functionality provided by UCM6100 model consists of Static defense, Dynamic defense and
Fail2ban. User could manually configure each of the three options to block certain malicious attack.
STATIC DEFENSE
It can be configured from Web UI->Settings->Firewall->Static Defense. One main purpose of static
defense is using pre-configured filtering rules. Three type of filtering rules are supported, ACCEPT,
REJECT, and DROP. UCM6100 administrator can configure filtering rules based on source/destination IP
addresses and ports. For example, if a remote host allowed to connect to a certain service using port X is
known with IP x.x.x.x, the administrator can create an ACCEPT rule to allow traffic from IP x.x.x.x destined
to port X on UCM6100.
The options to configure static defense rule are as follows:
Rule Name: Created by user to identify this rule.
Action: Accept, Reject or Drop depending on how the user would like the rule to perform.
Type: In/out indicates the traffic direction.
Interface: Select network interface where the traffic will go through.
Service: Users can select the pre-defined service (FTP/SSH/Telnet/TFTP/HTTP/LDAP) or “Custom”
which allows a specific restriction. If “Custom” is selected, please define source and destination IP
address + Port. Users need to select “Protocol” as TCP, UDP or Both.
In addition, Static Defense also provides three pre-configured defense mechanism:
1. Ping Defense
Once enabled, ICMP response will not be allowed for Ping request. This is a predefined mechanism in
order to protect flooding Ping attack.
2. SYN-Flood Defense
Once enabled, UCM6100 can response to the SYN flood denial-of-service (DOS) attack.
3. Ping-of-Death defense
Once enabled, UCM6100 can response to the Ping packet that is greater than 65,536 bytes.

UCM6100 Security Manual Page 17 of 23
STATIC DEFENSE EXAMPLE: BLOCKING TCP CONNECTION FROM A SPECIFIC HOST
This example demonstrates how to set up a new rule to block a host with a specific IP address to connect
to UCM6100 using TCP connection. In the following figure, 192.168.40.142 is the host IP address and
192.168.40.131 is the UCM6100’s IP address. Port 8089 on UCM6100 is used for HTTP server/web UI
access. This setting will block host on 192.168.40.131 to access UCM6100 port 8089 using TCP
connection.
Figure 9: Firewall Rule Custom Configuration
Figure 10: Static Defense Blocking Host 192.168.40.142 Using TCP Connection
After saving and applying the change, host 192.168.40.142 will not be able to access UCM6100 web UI
anymore.

UCM6100 Security Manual Page 18 of 23
Figure 11: Host blocked by UCM6100
STATIC DEFENSE EXAMPLE: BLOCKING SSH CONNECTION TO UCM6100
The UCM6100 can be accessed via SSH connection by default. The SSH access provides device status
information, reboot, reset and limited configuration capabilities. It is recommended to disable it once the
UCM6100 is deployed for security purpose. This can be done using static defense.
Figure 12: UCM6100 SSH Access

UCM6100 Security Manual Page 19 of 23
Configuration steps:
1. In UCM6100 web UI->Settings->Firewall->Static Defense page, click on “Create New Rule”.
2. In the prompt window, configure the following parameters:
Rule Name: Configure a name to identify this rule.
Action: Reject.
Type: IN.
Interface: WAN (for UCM6102).
Service: SSH.
Figure 13: Block SSH Connection
3. Save and apply changes.
Now SSH connection to the UCM6100 will not be allowed anymore from any host.
Figure 14: Putty Setup for SSH Connection