GRAYHILL 3D50 Series User manual

Bulletin 1250 rev.0817
Series 3D50 Development Kit
Quick Start Guide

3D50 Dev Kit –Quick Start Guide 1 Bulletin 1250 rev.0817
Revision History
Revision
Date
Description
A
12/16/2015
Original Release
B
03/07/2016
Added USB to CAN adapter to equipment list
C
04/28/2016
Added Appendix A.
D
08/30/2017
Minor corrections

3D50 Dev Kit –Quick Start Guide 2 Bulletin 1250 rev.0817
Introduction
These instructions describe how to connect the 3D50 Display to its development board and how to
connect the power, Ethernet, CAN bus, and RS-232 serial bus.
Equipment from Grayhill Included with 3D50Dev-100 Kit
3D50VT-100 Display
3D50 Mounting Frame
3D50 Development Stand
3D50 Breakout Board
3D50 18-pin DT cable to connect 3D50 Display to Breakout Board
USB to CAN adapter to provide CAN port for PC
DB9 cable to connect CAN adapter port to 3D50 Breakout Board
12VDC Universal Power Supply
DB9 cable to connect PC serial port to 3D50 Breakout Board *
USB to Ethernet adapter to provide Ethernet port on 3D50 *
Ethernet cable to connect PC Ethernet port to 3D50 Ethernet adapter *
* These items are only provided on kits shipped after January 1, 2016
Insert Card
The Insert Card directs users to the following links for downloading software development tools
and product literature:
http://www.grayhill.com/vui-builder/
http://www.grayhill.com/qt43d/
http://www.grayhill.com/codesys/
Hardware Setup Instructions
The following steps describe how to set up the 3D70 hardware. Take care to avoid damaging the development
board. Note that the color of the cables shown in the pictures below may be different than the color of the
cables provided.
1. Mount the 3D50 Display to
the mounting frame using
the four provided screws
2. Open the rubber cover on
the back of the 3D50
display and plug in the USB
to Ethernet adapter.

3D50 Dev Kit –Quick Start Guide 3 Bulletin 1250 rev.0817
3. Connect the 18-pin DT
cable to Breakout Board. Be
sure to match Pin 1 on the
cable to Pin 1 on the
Breakout Board.
4. Connect 18-pin DT cable to
back of the 3D50 Display.
Note that this connector is
keyed.
5. Mount the frame with the
3D50 Display to the
Breakout Board.
6. Connect Ethernet cable to
USB to Ethernet adapter.

3D50 Dev Kit –Quick Start Guide 4 Bulletin 1250 rev.0817
7. Connect DB9 serial cable to
Breakout Board COM 1
port.
8. Attach other end of this
cable to the serial port on
the development PC.
9. Connect the power cable to
the Breakout Board.
10. Attach the other DB9 cable
to the CAN 1 port on the
Breakout Board.
11. Attach the other end of this
cable to the USB to CAN
adapter.
PC to CAN-bus Interface
The Series 3D50 Display device has two CAN bus interfaces that can be used for various purposes.
The GridConnect USB-to-CAN adapter and software is a PC to CAN-bus interface that can be used for
monitoring and sending messages on the CAN bus. The GridConnect software can be installed on the
development PC as shown below:

3D50 Dev Kit –Quick Start Guide 5 Bulletin 1250 rev.0817
1. Insert the disc or download the software from
www.gridconnect.com and install the PCAN
USB software.
2. A copy of the Dynamic Link Library
(PCANBasic.DLL) provided with the USB PCAN
adapter needs to be copied to the Windows PC.
It is recommended that the DLL be copied to
the same folder as the application (e.g., VUI
Builder) that will be using it. Make sure that the
32-bit version is used as opposed to the 64-bit
version of the DLL. (Note: The PCANBasic.dll
file can be found in the folder
“\PreRelease\PCAN-Basic v3.4 (CAN-FD
Support)\Win32” on the disc. It’s also available
on the GridConnect web site under “Support ->
Product Packages -> PCAN-USB package”. Then
look in the download file “usb.zip” under the
folder “PCAN-Basic API\Win32\”.)

3D50 Dev Kit –Quick Start Guide 6 Bulletin 1250 rev.0817
Appendix A
POWER REQUIREMENT
Voltage: 12V
Current: 1.5A
J6, J7, J9, J10
TYCO
747844-6
J2, J3
CUI
RCJ-014-SMT
J12
CUI
PJ-002AH
J1 MAIN CONNECTOR Mating Connector
HOUSING: DEUTSCH DT16-18-SA-K004
TERMINAL: DEUTSCH 0462-201-16141
SCHEMATIC

3D50 Dev Kit –Quick Start Guide 7 Bulletin 1250 rev.0817
MAIN CONNECTOR (J1)
POWER SWITCHES VBAT (SW1) and VSW (SW2)

3D50 Dev Kit –Quick Start Guide 8 Bulletin 1250 rev.0817
VIDEO INPUTS CAM1 (J2) and CAM2 (J3)
CAN CONNECTORS CAN1 (J6) and CAN2 (J7)
RS232 CONNECTOR COM1 (J9)
IO CONNECTOR I/O1 (J10)

3D50 Dev Kit –Quick Start Guide 9 Bulletin 1250 rev.0817
DIP Switch SW3
Leave both switches open (OFF) for normal operation.
Closing both switches (ON) connects CAN port 1 to CAN port 2.
DIP Switch SW4
Leave all switches open (OFF) for normal operation.
Closing switch 1 (ON) connects DIG_IN_1 to IO1
Closing switch 2 (ON) connects IO2 to IO1
Closing switch 3 (ON) connects IO2 to IO3
Closing switch 4 (ON) connects IO4 to IO3
Closing switch 5 (ON) connects TXD1 to RXD1

3D50 Dev Kit –Quick Start Guide 10 Bulletin 1250 rev.0817
LEDs D2, D3, D4, D5, and D6
LEDs are illuminated if their corresponding signal is high.