Great Little Trading L4975 User manual

1
Coffee Cup Wooden Play Kitchen
23/03/2021
V2
easy - medium - hard
Assembly Difculty
one-person job
L4975
A few important pointers before you start:
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools.Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the tools
you need at the beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete, just
in case you accidentally discard smaller parts or hardware.
Thank you for shopping with GLTC, we hope you enjoy
having this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail
through the whole process. But if it all feels a bit too much
like hard work, then we do have an assembly company we
can recommend: the Flatpack Construction Company offers a
nationwide service and can be contacted on 0843 289 4951 or
www.atpackconstruction.co.uk.

2
Safety Warnings:
• WARNING! Not suitable for children under 3 years due to small parts
which may become detached and present a choking hazard.
• CAUTION Adult assembly required. Assembly to be carried out by a
competent adult only.
• Remove all packaging before giving to your child.
• In an unassembled state product contains small parts which may pose
a choking hazard, not suitable for children under 3 years.
• Assemble and use on a at and level surface.
• During assembly children should be kept away from the product due
to possible risk of injury.
• Do not use this item if any components are missing or damaged.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• Always use the anti-tip wall strap provided.
• To avoid possible injury from tipping - DO NOT allow children to
climb on the product.
• Check all xtures and ttings regularly and tighten as necessary.
• Assembly to be carried out by a competent adult only.
• Please retain this information for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean using a soft damp cloth followed by a dry cloth.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [e-mail]
Thank you
Registered Address:
GLTC Ltd, 12 Buckhold Road,
Wandsworth, London, SW18 4GP, United Kingdom
Authorised Representative:Authorised
Representative Service, 77 Camden Street Lower,
Dublin, D02 XE80, Ireland

3
Component Check List
A
1x 1x 1x
1x 1x 1x
B C
D E F
1x 1x
1x
1x
1x
1x
1x
1x
GHI
J K L
1x
1x
1x
TU V
M N P
1x
1x
1x
1x
WX Y
1x
1x
1x 1x
Z AA
#1
1x
#2 #3
#4 #5 #6
#7 #8 You will need
(not supplied)
Phillips Head Screwdriver
Q R S
1x
1x
Anti-Tip Strap
AB
13x Barrel Nut
Bolts
40mmL
13x Barrel Nuts
7mm dia
1x Door
Catch
1x Door
Catch
4x Short Screws
8mmL
6x Medium Screws
16mmL
21x Long Screws
21mmL
1x
O

4
STEP 1:
Attach the door catch (#1) to panel A using 2x
short screws (#5).
STEP 2:
Attach the handle (C) to the door (B) using 2x long
screws (#7). Attach the door catch (#2) to the door
using 2x short screws (#5).
Hardware for Step 2:
2x #7 21mmL screws
2x #5 8mmL screws
1x #2 door catch
Hardware for Step 3:
Hardware for Step 4:
2x #6 16mmL screws
4x #6 16mmL screws
STEP 3:
Attach the soap drawer rest (E) to the back of the control panel (D) using 2x
medium screws (#6).
STEP 4:
Slide part assembled soap drawer (F) through the cut out on control panel(D).
Now secure panel back panel G to soap drawer (F) using 4x medium screws (#6).
A
B
D
G
#1
#5
#5
#5
#5
#7
#7
#2
#6
#6
#6
#6
F
E
C
Hardware for Step 1:
2x #5 8mmL screws
1x #1 door catch
2x
2x
D

5
Hardware for Step 5:
2x #3 barrel nuts
2x #4 barrel nut bolts
STEP 5:
Secure left hand side panel (H) to base panel (I) using 2x barrel nuts and bolts.
STEP 6:
Loosely attach right hand side panel (J) to base panel (I) using 2x barrel nuts and
bolts.With the panel J loosely attached now slide front plinth (K) into the dowel
holes on the inside faces of panel H and J.
With panel K now in place, now fully tighten the barrel nut bolts to fully secure
right hand side panel (J) to base panel (I).
STEP 7:
Secure dividing panel A to base panel (I) using 2x barrel nuts and bolts. Do not fully
tighten.You will need the panel to be slightly loose in order to complete step 8.
J
H
I
M
#3
#3 #4
#4
K
Hardware for Step 6:
2x #3 barrel nuts
2x #4 barrel nut bolts
Hardware for Step 7:
2x #3 barrel nuts
2x #4 barrel nut bolts
H
#4
#4 #3
#3
I
A
I
#4
#3
#4
#3
Loosely tighten
Do not fully tighten
STEP 8:
Gently push the dowels
on washing machine door
panel (L) into the holes on
the internal faces of panel
H and A.
Now slot the oven tray
(M) into the slots on the
internal faces of panels J
and A.
With panels L and M in
position. Now fully tighten
the barrel nuts and bolts
securing panel A to I.
L
H
J
A
Now fully
tighten

6
STEP 9:
Slide back panel (N) into the grooves on the internal faces of panels H,A and I,
Slide back panel (O) into the grooves on the internal faces of panels J,A and I,
STEP 10:
Firstly locate the oven door
hinge on panel B into the hinge
hole on panel 1.
Now position panel D between
panels H and J. So its rests on
the cut out on panel A. At the
same time ensure the oven
door hinge goes into the hinge
hole on underside of panel D
Now secure panel D to panels
H and J using 4x long screws
(#7).
STEP 11:
Now attach tap section (Q) to the worktop (P) using 2x long screws (#7).
STEP 12:
Carefully lower the worktop (P)
onto panels D,A, N and O.
Secure the worktop (P) into position
between panels H and J using 4x
long screws (#5).
O
P
N
#7
#7
#7
#7
#7
#7
#7
#7
#7
#7
Q
H
J
A
Hardware for Step 10:
6x #7 21mmL screws
#7
#7
H
J
A
D
I
B
Finally secure panel D to panel A using 2x long screws (#7).
A
Hardware for Step 11:
2x #7 21mmL screws
P
H
J
D
N
O
Hardware for Step 12:
4x #7 21mmL screws
I
A

7
STEP 13:
Carefully slide backboard (R) into
the grooves on panels H, J and O.
STEP 15:
Carefully slide backboard (T) into the
grooves on panels H, J and S.
STEP 16:
Secure panel X to panel S using 1x
barrel nut and bolt.
Now slot panelsV and U into panel S.
At the same time slot shelf (W) into the
cut outs on the internal faces of panels
X and V.
R
W
V
U
X
S
#3
P
H
J
Hardware for Step 14:
4x #3 barrel nuts
4x #4 barrel nut bolts
STEP 14
Secure panel S to panels H an J
using 4x barrel nuts and bolt.
The groove on the underside
of panel R should slot into
backboard (R).
#3
#3
#3
#4
2x
#4
2x
H
J
R
T
Hardware for Step 16:
1x #3 barrel nut
1x #4 barrel nut bolt
S
H
J
S
#3
#4

8
STEP 17:
Slot the dowels on panel
Y into the holes on the
top of panel S.
Now insert sink (AB)
into the cut out on the
worktop (P).
STEP 19:
Carefully position panel Z between panels
H and J, ensuring panels X, V and U slot
into the cut outs on the underside of
panel Z.
Secure panel Z to panels H and J using 4x
long screws (#7).
Now secure panel Z to panel X using 1x
barrel nut and bolt.
STEP 20:
Secure panel T to panel Z using 2x long screws (#7).
Now Attach the anti tip strap (#8) to the back of
the unit using 1x barrel nut and screw.
The barrel nut also secures panel Z into position.
The strap should now be attached to the wall using
hardware that is suitable for the walls in your home
(not provided).
STEP 18:
Secure the coffee machine (AA) to panel Z using
1x long screw (#7).
Copyright© 2020 G.L.T.C. Ltd. All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.
AA
Z
#7
#7
Y
AB
P
S
Hardware for Step 18:
1x #7 21mmL screw
Hardware for Step 19:
4x #7 21mmL screws
1x #3 barrel nuts
1x #4 barrel nut bolts
#7
#7
#7
#4
#3
Z
H
J
X
VU
Hardware for Step 20:
2x #7 21mmL screws
1x #3 barrel nuts
1x #4 barrel nut bolts
1x #8 anti - tip strap
T
Z
#7
#7
#3
#8 #4