Great Little Trading Star Bright Chest of Drawers - Tall Boy User manual

1
Star Bright Chest of Drawers - Tall Boy
A few important pointers before you start:
• It might be worth checking on our website that there are no updates
or revisions to these instructions (if we have had helpful feedback from
other customers we pass it on via the product web page). Simply check
the date and version number on the front of this leaet against that of
any site updates.
• Please read the instructions right through before you start, and check
that all the components have been included in the pack; we nd
separating all the hardware into piles makes it easier to be sure that
everything is present and correct.
• Make sure you have the right tools. Allen keys are provided if required,
but screw drivers and other tools are not. You’ll nd details of the
tools you need at the beginning of the instructions.
• It’s a good idea to build the unit in the room where you are going to be
using it, to avoid the need to move it after it’s been assembled.
• Do not throw away any packing materials until assembly is complete,
just in case you accidentally discard smaller parts or hardware.
L4644
02/11/2018
V1
easy - medium - hard
Assembly Difculty
Thank you for shopping with GLTC, we hope you enjoy having
this product in your home.
We know assembling furniture, toys or accessories is not everyone’s
favourite way to spend their time, so we’ve tried to make assembling
this item as quick and painless as possible.
Hopefully our efforts will have been worthwhile and you’ll sail through
the whole process. But if it all feels a bit too much like hard work, then
we do have an assembly company we can recommend: the Flatpack
Construction Company offers a nationwide service and can be
contacted on 0843 289 4951 or www.atpackconstruction.co.uk.
Good luck!
one-person job

2
Safety Warnings:
• Adult assembly required.
• Unassembled product contains small parts which may present a
choking hazard.
• Children should be kept away from the product during assembly to
avoid any possible risk of injury
• Assemble and use on a at and level surface.
• This product is heavy, we recommend that you build it where you are
planning to use it.
• DO NOT use power tools in the assembly of this product as there is a
risk of over-tightening and consequently splitting of the wood.
• To avoid possible injury from tipping, DO NOT allow children to climb
on the product.
• WARNING! FURNITURE TIPPING RISK. Serious or fatal crushing
injuries can occur from furniture tipping over.Ensure you secure this
furniture product to the wall before you use it using the kit provided. If
you have not received an anti-tip kit with your product please contact
Customer Services.
• Check all xtures and ttings regularly and tighten as necessary.
• Please retain these instructions for future reference.
Customer Service:
• If you nd that any components are missing or damaged, please do
not begin assembly and do not use the item. Please contact GLTC
Customer Services on 0344 848 6000 immediately.
• We do stock spare hardware packs at our warehouse, so we should be
able to send you a replacement pack immediately if required.
Product Care:
• Wipe clean only.
• Do NOT use cleaning products which contain ammonia, solvents or
abrasive material.
• Do NOT expose the item to extremes of heat and humidity.
Could we do better?
If there is anything you think could be improved in these instructions or in
the assembly of this product we’d be grateful if you could let us know; we’ll
pass any helpful hints and tips on to other customers via our website and
update the instructions.
All you need to do is drop us a line at [email protected]
Thank you.

3
Component Check List
A B
Component Check List
K
C D
EF
G H
I J
x5 Drawer Frontx1 Horizontal Divider Panel x1 LH Side Panel
x1 RH Side Panel x1 Base Plinth
x1 Top Panel x1 Back Panels
x5 Drawer LH Sides x5 Drawer RH Sides
x5 Drawer Base Panels
x5 Drawer Back Panels

4
Component Check List
#1 #2
Component Check List
#11 #12
You will need (not supplied)
#3 #4
Philips Head Screwdriver
#5 #6
#7 #8
#9 #10
1x Allen Key
x10 Screws
16mmL
x5 #1 Flat Runner x5 #2 Flat Runner
x5 RH L-Shaped Runners x5 LH L-Shaped Runners
x12 Wooden Dowels
25mmL
x20 Screws
25mmL
x28 Cam Dowels
35mmL
x28 Cam Locks
14mm diameter
x4 Barrel Nuts
10mmL
x4 Bolt
66mmL
x60 Screws
12mmL

5
Hardware for Step 1:
15x #12 12mmL Screws STEP 2:
Slot divider panel (A) to the xed hardware on LH side panel (B). Secure with x2 cam
locks (#8).
Hardware for Step 2:
2x #8 Cam Locks
STEP 1:
Locate LH side panel (B) and align as shown with the ledged side at the top. Line
up all x5 at runners (#1) ensuring that the wheel of the runers are away from the
ledged side. Secure each runner with x3 screws (#12) where shown.
Once all the runners are attached insert x2 wooden dowels and x2 cam dowels
(#7) where shown.
#1
#1
#1
#1
#1
#1
#5
#5
#7
#7
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#7
#7
#5
#5
#8
#8
AB
2x #5 Wooden Dowels
2x #7 Cam Dowels
5x #1 Flat Runners

6
STEP 3:
Locate RH side panel (C) and align as shown with the ledged side at the top. Line up
all x5 at runners (#2) ensuring that the wheel of the runers are away from the ledged
side. Secure each runner with x3 screws (#12) where shown.
Once all the runners are attached insert x2 wooden dowels and x2 cam dowels (#7)
where shown.
STEP 4:
Slot RH side panel (C ) to the other panels ensuring that the large hardware holes are
at the top and the ledged side facing upwards. Afx panel (C ) with x2 cam locks (#8).
#2
#2
#2
#2
#2
#2
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#12
#7
#7
C
Hardware for Step 3:
15x #12 12mmL Screws
2x #7 Cam Dowels
CA
B
#5
#5
#8
#8
Hardware for Step 4:
2x #8 Cam Locks
2x #5 Wooden Dowels
5x #2 Flat Runners

7
#9 #9
#9
#9
#5
#5
#5
#5
#10
#10
#10
#10
CA
B
D
Hardware for Step 5:
STEP 5:
Attach base panel (D) using x4 barrel nuts (#9), x4 wooden dowels (#5) and securing
with x4 bolts (#10). Ensure that the ledged side of the base panel is facing upwards.
4x #10 Bolts
4x #9 Barrel Nuts
4x #5 Wooden Dowels
STEP 6:
Insert x4 cam dowels (#7) to top panel (E ).
E
#7
#7
#7
#7
Hardware for Step 6:
4x #7 Cam Dowels

8
STEP 7:
Afx top panel (E ) to the unit using x4 wooden dowels (#5) and securing with x4 cam
locks (#8).
E
C
A
B
D
#5
#5
#5
#5
#8
#8
#8
#8
Hardware for Step 7:
4x #8 Cam Locks
4x #5 Wooden Dowels
E
A
D
C
B
F
#11
#11
#11
#11
#11
#11
#11
#11
#11
#11
Hardware for Step 8:
10x #11 18mmL Screws
STEP 8:
Place back panel (F) into the recess ensuring the hardware holes line up. Secure using
x10 screws (#11).
Please note that the 2x pilot holes indicated at the top of the unit are to attach anti-tip
straps included separately with this item.

9
#7
#7
#7
#7 I
STEP 9:
Insert x4 cam dowels (#7) to the x5 drawer front panels (I).
Hardware for Step 9:
20x #7 Cam Dowels
#4
#12
#12
#12
#12
#12
#12#4
G
Hardware for Step 10:
STEP 10:
Locate x5 LH drawer sides (G) and secure L-shaped runner (#4) with x3 screws (#12)
where shown. Repeat for each of the panels (G).
15x #12 12mmL Screws
5x #4 LH L-Shaped Runners

10
#3
#12
#12
#12
#12
#12
#12
#3
H
Hardware for Step 11:
15x #12 12mmL Screws
5x #3 RH L-Shaped Runners
STEP 11:
Locate x5 RH drawer sides (H) and secure L-shaped runner (#3) with x3 screws (#12)
where shown. Repeat for each of the panels (H).
STEP 12:
Construct the drawer by attaching side panels (G and H) to back panel (K) as shown
with 4x screws (#6). Ensure that the runners are on the outer side of the side panels
and that the wheels on the runners are at the back of the drawer.
Slide in the drawer base panel (J) into the grooves and insert 4x cam locks (#8) into
the hardware holes at the front of the drawer.Then slot in the drawer front panel (I)
and secure the 4x cam locks (#8).
Repeat until all x5 drawers are constructed.
#6
#6
#6
#6
K
G
H
J
I
#8
#8
#8
#8
Hardware for Step 12:
20x #8 Cam Locks
20x #6 25mmL Screws

11
I
I
I
I
I
STEP 13:
Insert the x5 drawers to the unit.
STEP 14:
Your unit is ready to use.
Please be aware that we advise that safety straps are used to secure this to the wall,for
details on securing the unit to the wall see the anti-tip kit instructions included with
this product.Alternative furniture safety straps are available at www.gltc.co.uk
Copyright© 2018 G.L.T.C. Ltd.All rights reserved.
Great Little Trading Company and GLTC are registered trade marks of G.L.T.C. Limited.