Gree GMV-ND180PHS/B-T User manual

Owner's Manual
Original Instructions
Commercial Air Conditioners
Multi Variable Air Conditioners
Ducted Type Indoor Unit
Models:
GMV-ND22PHS/B-T GMV-ND25PHS/B-T GMV-ND28PHS/B-T GMV-ND32PHS/B-T
GMV-ND36PHS/B-T GMV-ND40PHS/B-T GMV-ND45PHS/B-T GMV-ND50PHS/B-T
GMV-ND56PHS/B-T GMV-ND63PHS/B-T GMV-ND71PHS/B-T GMV-ND80PHS/B-T
GMV-ND90PHS/B-T GMV-ND100PHS/B-T GMV-ND112PHS/B-T GMV-ND125PHS/B-T
GMV-ND140PHS/B-T GMV-ND160PHS/B-T GMV-ND180PHS/B-T

To Users
Thank you for selecting Gree product. Please read this instruction manual carefully before
installing and using the product, so as to master and correctly use the product. In order to guide you
to correctly install and use our product and achieve expected operating effect, we hereby instruct as
below:
(1) This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
(2) In order to ensure reliability of product, the product may consume some power under stand-
by status for maintaining normal communication of system and preheating refrigerant and
lubricant. If the product is not to be used for long, cut off the power supply; please energize
and preheat the unit in advance before reusing it.
(3) Please properly select the model according to actual using environment; otherwise it may
impact the using convenience.
(4) This product can’t be installed at corrosive, inflammable or explosive environment or the
place with special requirements, such as kitchen. Otherwise, it will affect the normal operation
or shorten the service life of the unit, or even cause fire hazard or serious injury. As for above
special places, please adopt special air conditioner with anti-corrosive or anti-explosion
function.
(5) If the product needs to be installed, moved or maintained, please contact our designated
dealer or local service center for professional support. Users should not disassemble or
maintain the unit by themselves, otherwise it may cause relative damage, and our company
will bear no responsibilities.
(6) All the illustrations and information in the instruction manual are only for reference. In order
to make the product better, we will continuously conduct improvement and innovation. If there
is adjustment in the product, please subject to actual product.

Exception Clauses
Manufacturer will bear no responsibilities when personal injury or property loss is caused by the
following reasons:
(1) Damage the product due to improper use or misuse of the product;
(2) Alter, change, maintain or use the product with other equipment without abiding by the
instruction manual of manufacturer;
(3) After verification, the defect of product is directly caused by corrosive gas;
(4) After verification, defects are due to improper operation during transportation of product;
(5) Operate, repair, maintain the unit without abiding by instruction manual or related regulations;
(6) After verification, the problem or dispute is caused by the quality specification or performance
of parts and components that produced by other manufacturers;
(7) The damage is caused by natural calamities, bad using environment or force majeure.

Contents
1 Safety Notices (Please be sure to abide) ................................................................. 1
2 Product Introduction ................................................................................................. 3
2.1 Names of Key Components.................................................................................................3
2.2 Rated Working Condition.....................................................................................................3
3 Preparations for Installation ..................................................................................... 3
3.1 Standard Fittings .................................................................................................................4
3.2 Location for Installation........................................................................................................4
3.3 Requirements for Communication Line ...............................................................................5
3.4 Wiring Requirements ...........................................................................................................6
4 Installation Instructions ............................................................................................ 7
4.1 Installation of Indoor Unit.....................................................................................................7
4.2 Refrigerant Pipe Connection ...............................................................................................9
4.3 Drainage Pipe Installation and Drainage System Testing..................................................10
4.4 Installation of Air Duct........................................................................................................13
4.5 Installation of Wired Controller ..........................................................................................15
5 Wiring Work.............................................................................................................. 15
5.1 Connection of Wire and Patch Board Terminal..................................................................16
5.2 Power Cord Connection ....................................................................................................17
5.3 Connection of Communication Wire between Indoor Unit and Outdoor Unit (or indoor unit)
.................................................................................................................................................17
5.4 Connect Communication Wire of Wired Controller............................................................18
5.5 Illuminate for Connection of Wired Controller and Indoor Units Network ..........................19
6 Setting of External Static Pressure ........................................................................ 21
7 Routine Maintenance............................................................................................... 21
7.1 Cleaning of Filter ...............................................................................................................21
7.2 Maintenance before the Seasonal Use .............................................................................21
7.3 Maintenance after the Seasonal Use ................................................................................22
8 Table of Error Codes for Indoor Unit...................................................................... 22
9 Troubleshooting....................................................................................................... 23

Multi Variable Air Conditioners Ducted Type Indoor Unit
1
1 Safety Notices (Please be sure to abide)
WARNING!If not abide strictly, it may cause severe damage to the unit or the people.
NOTE! If not abide strictly, it may cause slight or medium damage to the unit or the people.
This sign indicates that the operation must be prohibited. Improper operation may cause
severe damage or death to people.
This sign indicates that the items must be observed. Improper operation may cause damage
to people or property.
WARNING!
This product can’t be installed at corrosive, inflammable or explosive environment or the
place with special requirements, such as kitche
n. Otherwise, it will affect the normal
operation or shorten the service life of the unit, or even cause fire hazard or serious injury.
As for above special places, please adopt special air conditioner with anti-corrosive or anti-
explosion function.
This Multi
VRF System shall only be connected to an appliance suitable for the same
refrigerant.
All units in Manual Cover is a partial unit, complying with partial unit of IEC 60335-2-40:2018,
and must only be connected to other units that have been confirmed
as complying to
corresponding partial unit requirements of this international standard.
The electrical interface shall comply with electrical security requirement,current shall be
referred to the table of “Dimension of power cord and capacity of air switch” in Section 3.4,
and safety class of construction is I.
Please install the unit according
to instructions in this manual.
Read this manual carefully
before starting up or checking
the machine.
Installation should be performed
by dealer or qualified
technicians. Do not install the
product by yourself. Improper
installation may result in water
leakage, electric shock or fire
hazard.
Make sure the local power
supply is in accordance with
units before installation, and
check the power supply
carefully.
This air conditioner must be
properly grounded through the
receptacle to avoid electric
shock. The grounding wire
shouldn't be connected with gas
pipe, water pipe, lightning
arrester or telephone line.
Please use specialized
accessories or parts to carry out
installation, or water leakage,
electric shock, fire hazard may
resulted.
R410A refrigerant can produce
poisonous gas once it meets
fire, so please ventilate the room
immediately if refrigerant leaks
out during installation.

Multi Variable Air Conditioners Ducted Type Indoor Unit
2
Diameter of power cord must be
large enough. Damaged power
cord and connecting wire must
be replaced by specialized
electric cable.
After the power cord is
connected, please install the
cover of electric box to avoid
danger.
Nitrogen must be charged
according to technical
requirements.
Short circuit is forbidden. Do not
cancel the pressure switch in
case the unit may be damaged.
For units with wired controller,
do not connect power supply
until the wired controller is well
installed. Otherwise, the wired
controller cannot be used.
When the installation is finished,
please check and make sure the
drain pipe, pipeline and electric
wire are all well connected in
order to avoid water leakage,
refrigerant leakage, electric
shock or fire hazard.
Do not extend fingers or objects
into air outlet or air return grille.
If you use gas heater or
petroleum heater in the same
room, please open the door or
window to maintain good air
circulation in case the room may
lack of oxygen.
Never start or stop the air
conditioner by inserting or
removing the power cord.
Do not turn off the air conditioner
until it runs for at least 5
minutes. Otherwise, oil-return of
the compressor will be affected.
Children are not allowed to
operate the air conditioner. Do not operate the air conditioner with wet hands.
Please turn the unit off and
unplug your air conditioner
before cleaning. Otherwise, it
may cause electric shock or
personal injury.
Do not spray water on the air
conditioner or it will cause
malfunction or electric shock.
Do not expose the air
conditioner directly to water or
place it in a damp or corrosive
environment.
Connect power supply 8 hours
before operation. Do not
disconnect power if you want to
stop the unit in a short period of
time, e.g. in one night (This is for
protecting the compressor).
Volatile liquid like thinner or
gasoline will damage the
appearance of air conditioner.
Please use soft dry cloth or wet
cloth with mild detergent to clean
the outer case of air conditioner.
During Cooling mode, indoor
temperature should not be set
too low. Keep the difference
between indoor temp and
outdoor temp within 5℃.

Multi Variable Air Conditioners Ducted Type Indoor Unit
3
If abnormal condition occurs
(e.g. unpleasant smell), please
turn off the unit at once and
disconnect power supply. Then
contact GREE service center. If
the air conditioner continues to
operate despite of abnormal
condition, the unit may be
damaged and it may cause
electric shock or fire hazard).
Do not repair the air conditioner
by yourself. Improper repair will
cause electric shock or fire
hazard. Please contact GREE
service center and have it
repaired by professional
technicians.
Any personal injury or property loss caused by improper installation, improper debug,
unnecessary repair or not following the instructions of this manual should not be the responsibility of
Gree Electric Appliances, Inc. of Zhuhai.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material
resources. To return your used device, please use the return and collection systems or contact
the retailer where the product was purchased. They can take this product for environmental
safe recycling.
2 Product Introduction
2.1 Names of Key Components
Fig.2.1
2.2 Rated Working Condition
—Indoor Side Condition Outdoor Side Condition
Dry Bulb Temp(℃) Wet Bulb Temp(℃) Dry Bulb Temp(℃) Wet Bulb Temp(℃)
Rated Cooling 27 19 35 24
Rated Heating
20
15
7
6
3 Preparations for Installation
NOTE! Product graphics are only for reference. Please refer to actual products. Unspecified
measure unit is mm.

Multi Variable Air Conditioners Ducted Type Indoor Unit
4
3.1 Standard Fittings
Please use the supplied standard fittings listed below as instructed.
No.
Name
Appearance
Q'ty
Usage
1 Wired Controller 1 To control the indoor unit
2
Drain Hose Assembly
1
To connect with the hard PVC drain pipe
3 Special Nut
2 GMV-ND22~50PHS/B-T
1 GMV-ND56~180PHS/B-T
4
Corrugated pipe
1
GMV-ND56~180PHS/B-T
5 M10×8 Nut with Washer 4 To be used together with the hanger bolt
for installing the unit
6 M10 Nut (M10×8.4 Nut) 4 To be used together with the hanger bolt
for installing the unit
7 M10 Washer (Spring
Washer M10×2.6)
4 To be used together with the hanger bolt
for installing the unit
8 Insulation 1 To insulate the gas pipe
9 Insulation 1 To insulate the liquid pipe
10 Sponge 2 To insulate the drain pipe
11
Fastener
8
To fasten the sponge
NOTE: User can purchase remote controller and receiver otherwise by himself.
3.2 Location for Installation
(1) The appliance shall not be installed in the laundry.
(2) The top holder must be strong enough to support unit’s weight.
(3) Drain pipe can drain water out easily.
(4) There is no obstacle at inlet or outlet. Please ensure good air circulation.
(5) In order to make sure the space for maintenance, please install the indoor unit according to
the dimension described below.
(6) Keep the unit away from heating source, inflammable gas or smoke.
(7) This is a concealed ceiling type unit.
(8) Indoor unit, outdoor unit, power cord and electric wire should stay at least 1m from the TV
set and radio. Otherwise, these electrical appliances may have image interference and noise
(Even if the distance is 1m, when there is strong electric wave, noise may still occur)

Multi Variable Air Conditioners Ducted Type Indoor Unit
5
Unit: mm
Fig.3.2
NOTES!
①Installation of the unit must be in accordance with National Electric Codes and local
regulations.
②Improper installation will affect unit’s performance, so do not install the unit by yourself.
Please contact local dealer to arrange professional technicians for the installation.
③Do not connect power until all installation work is finished.
3.3 Requirements for Communication Line
CAUTION!
If air conditioner used under strong electronic-magnetic interference circumstance, STP (shielded
twisted pair) communication cable must be adopted.
3.3.1 Select Communication Line for Indoor Unit and Wired Controller
Fig.3.3.1

Multi Variable Air Conditioners Ducted Type Indoor Unit
6
Material type
Total length of
communication line
between indoor unit and
wired controller L (m)
Wire size
(mm²)
Material
Standard Remarks
Light/Ordinary
polyvinyl chloride
sheathed cord.
(60227 IEC 52
/60227 IEC 53)
L≤250 2×0.75~2×1.
25
IEC
60227-5
1) Total length of communication
line can't exceed 250m.
2) The cord shall be Circular cord
(the cores shall be twisted
together).
3) If unit is installed in places with
intense magnetic field or strong
interference, it is necessary to
use shielded wire.
3.3.2 Select Communication Line for Indoor Unit and Indoor Unit (Outdoor Unit)
Fig.3.3.2
Material Type
Total Length L (m) of
Communication Cable
between Indoor Unit
and Indoor (Outdoor)
Unit
Wire size
(mm²)
Material
Standard Remarks
Light/Ordinary
polyvinyl chloride
sheathed cord.
(60227 IEC 52
/60227 IEC 53)
L≤1000 ≥2×0.75 IEC 60227-5
1) If the wire diameter is enlarged to 2×1
mm², the total communication line length
can reach 1500 m.
2)
The cord shall be Circular cord (the cores
shall be twisted together).
3) If unit is installed in places with intense
magnetic field or strong interference, it is
necessary to use shielded wire.
3.4 Wiring Requirements
(1) Power Cord Size and Air Switch Capacity
Model Power Cord Size
Air Switch
Capacity
(A)
Minimum Sectional
Area of Ground Wire
(mm²)
Minimum Sectional
Area of Power Cord
(mm²)
GMV-ND22~180PHS/B-T 220~240V-1ph-50Hz
208~230V-1ph-60Hz
6 1.0 1.0