Gree Trendy Series User manual

1
115V
R410A
CANCEL
Model Remarks
Summary and features
Trendy Series

COOLING HEATING COOLING HEATING
3100/2500 (W) 3800/2750 (W) 4100/3500 (W) 4400/3850 (W)
10600/9000(Btu/h) 13000/9500(Btu/h) 14000/12000(Btu/h) 15000/13000(Btu/h
)
1250/730 1450/840 1450/1100 1550/1200
1250 1450 1450 1550
12 13.6 13.6 14.5
3.42 3.27 3.18 3.2
Model of Indoor Unit
Fan Motor Speed (r/min)
(H/M/L)
Output ofFan Motor (w)
Input Power of Heater (w)
Fan Motor Capacitor (uF)
Fan Motor RLA(A)
Fan Type-Piece
Diameter-Length (mm)
Evaporator
Pipe Diameter (mm)
Row-Fin Gap(mm)
Coil length (l) xheight(H) x
coil width (L)
Swing Motor Model
Output ofSwing Motor (W)
Fuse (A)
Sound Pressure Level dB
(A) (H/M/L)
Sound Power Level dB (A)
(H/M/L)***
Dimension (W/D/H)( mm)
Dimension of Package
(W/D/H)( mm)
Net Weight /Gross Weight
(kg)
Model GWHD09A3NA3IA
Function
Rated Voltage 115V
Frequency(Hz) (High/Standard *) 60HZ
Total Capacity(W) (High/Standard
*):
Total Capacity(Btu/h) (High/
Standard *):
Power Input (W) (High/ Standard*)
Rated Input (W) (High/Standard *)
Rated Current (A) (High/Standard
*)
Air Flow Volume (m3/h) (H/M/L)** 550
Dehumidifying Volume (l/h) 1.2
EER / C.O.P (W/W)
EnergyClass B
Indoor
unit
GWHD09A3NA3IA/I
high：1200 mid：1060low：700
13
/
1
0.18
Cross flow fan – 1
Ø97 X 583
Aluminum fin-copper tube
Ø7
2-1.4
681×324.3×38.1
MP28VA
2
Controller3.15 transformer0.2
43 /37 /30
53/47/40
770×190×250
830×296×330
8.5/12..5
GWHD12A6NA3IA
115V
60HZ
550
1.2
B
GWHD12A6NA3IA/I
high：1350 mid：1200 low：1100
20
/
4
0.28
Cross flow fan – 1
Ø92.1—616
Aluminum fin-copper tube
Ø7
2-1.4
681×324.3×38.1
MP28VA
2
Controller3.15 transformer0.2
11/14
43 / 37 / 30
53/47/40
830×225×285
875×312×372
2Specifications and technical parameters

GWHD09A3NA3IA/O GWHD12A6NA3IA/O
SANYO SANYO
C-6RZ092H1AB C-6RZ092H1AB
Twin rotory Twin rotory
33 33
3.92 3.92
960 960
Int11l-3979 Int11l-3979
Capillarythrottling Capillarythrottling
Transducer starting Transducer starting
-7℃≤T≤43℃-7℃≤T≤43℃
Aluminum fin-copper tube Aluminum fin-copper tube
9.52 9.52
2-1.4 2-1.4
645X508X44 645X508X44
830±20 830±20
30 30
0.3 0.3
2.5 2.5
1800 1800
Axial fan –1 Axial fan –1
400 400
Auto defrost Auto defrost
T1 T1
II
IP24 IP24
3.8 3.8
1.2 1.2
53 55
63 65
848X320X540 848X320X540
878X360X590 878X360X590
40/45 40/45
R410A/1.2 R410A/1.27
66
15 15
Liquid Pipe (mm) Ø6(1/4”) Ø6(1/4”)
Gas Pipe (mm) Ø12(1/2”) Ø12(1/2”)
Height(m) 5 5
Length (m) 15 15
Length (m)
Sound Pressure Level dB (A) (H/M/L)
Dimension (W/D/H)( mm)
Dimension of Package (W/D/H)(mm)
NetWeight /Gross Weight (kg)
Refrigerant Charge (kg)
Climate Type
Fan Type-Piece
Fan Diameter (mm)
Sound Power Level dB (A) (H/M/L)
Permissible Excessive Operating
Pressure for the Discharge Side(MPa)
Permissible Excessive Operating
Pressure for the Suction Side(MPa)
Isolation
Moisture Protection
Air Flow Volume ofOutdoor Unit (m
3
/h)
Output ofFan Motor (W)
Fan Motor RLA(A)
Defrosting Method
Compressor Power Input(W)
Fan Motor Capacitor (uF)
Working Temp Range (℃)
Coil length (l)xheight (H) xcoil width
(L)
Fan Motor Speed (rpm)
Rows-Fin Gap(mm)
Condenser
Pipe Diameter (mm)
CompressorModel
CompressorType
L.R.A. (A)
Compressor RLA(A)
Outdoor
unit
Connec
tion
Pipe
Gas additional charge(g/m)
Outer
Diameter
Max
Distance
Overload Protector
Throttling Method
Starting Method
Model of Outdoor Unit
Compressor Manufacturer/trademark
Trendy Series
The above parameters are subject to change without notices, please refer to the nameplate for reference.

3
Window
receiver
Part name
Indoor Unit
Outdoor Unit

4
Trendy Series
Overall and Installing Dimension
UOverall and Installing Dimension of Indoor Unit
Air inlet grill
Left piping hole Right piping hole
Top view
Rear view
Unit:mm
Wall-mounting plate

UOverall and Installing Dimension of Outdoor Unit
Unit: mm
Bolt
Nut
Wrench

5
Trendy Series
Circuit Diagram
These circuit diagrams are subject to change without notice. Please refer to the ones stuck on the machines.

66
66
6Manual of functions of remote controller and operation method
Manual of functions of remote controller
The room setting temperature(Tpreset)
The room ambient temperature (Tamb)
Temperature parameter
Basic Functions
It will delay 3 minutes for restarting unit after compressor is stoped.
Cooling Mode
Cooling Conditions and Process
When T amb. Tpreset , the unit will run under cooling mode, in which case the compressor \ indoor fan and outdoor fan
will start , the indoor fan will run at setting speed.
When T amb. Tpreset 2 , the compressor will stop, the outdoor fan will atop running after 30 seconds,the indoor fan will
run at setting speed.
When Tpreset 2 T amb. Tpreset+1 , the unit will maintain its original operating status.
Under this mode, the switchover valve will not be powered on, and the setting temperature range is16 ~30 .
Protection
Antifreeze Protection
When the antifreezing pretection is detected,the compressor will stop,the outdoor fan will stop after 30s , the
indoor fan motor and swing fan motor will run at original run conditions under the cool mode.Indoor fan motor
will run at low speed and indoor fan motor will run at oroginal conditions under the dehumidify mode.When ant
-ifreezing protection is eliminated and the compressor has stopped for 3 minutes,the whole unit will run in the
oroginal mode.
Overcurrent protection
If total current is high,the compressor wil run in limited frequency.If total current is over the stop-running current,then the
compressor will stop,the outdoor will delay 30 seconds to stop.
DRY Modes
The conditions and process of DRY
When T amb. Tpreset , the unit will run under DRY mode, in which case the compressor \indoor fan and outdoor fan
will be started and the indoor fan will run at low speed.
When Tpreset 2 T amb Tpreset , the unit will run with original setting.
This manual is applicable to DC inverter Trendy Series: GWHD09A3NA31A, GWHD12A6NA31A.
The centigrade is used for the following function manual, if there will be the Fahrenheit degree,
that will be TF=TCX1.8+32.
Tamb.
Tpreset
Tpreset
Compressor
Outdoor fan
Indoor fan
Running Stopping
Preset fan speed
3mins.
Start cooling
Original running status
Stop cooling
Running Stopping
Indoor fan
Outdoor fan
Compressor 3mins.
During anti-freezing protection

Trendy Series
When Tamb. Tpreset 2 , the compressor will be stopped, and outdoor fan will be stopped after 30 seconds,the indoor fan
will run at low speed.
Under this mode, the switchover valve will not be powered on, and the setting temperature range is 16 ~30 .
Protection function is the same with cool mode
HEAT Mode
The conditions and process of heating
When Tamb Tset 2 ,the system enters heating running, in this case, the reversal valve, compressor,
out fan enter simultaneously running.The indoor fan will run with setting fan speed and anti-coolwind will be runned.
When Tamb Tset 5 ,the compressor will stop, and outdoor fan will be stopped in 30 seconds,the indoor unit
will run at setting fan speed for 60s then will stop .The switchover valve will be powered off after compressor is
stopped for 2 minutes under heating-off mode or the condition that heat is changed to other modes
Under this mode, the switchover valve will be powered on, and the setting temperature range is16 ~30 .
When Tset 2 Tamb Tset 5 ,unit will keep the original operation status.
Conditions and processes of defrost
Fan mode
Auto Mode
Compressor
Outdoor fan
Indoor fan
Running Stopping
Low fan speed
Tpreset
Tpreset
Tamb. Cooling
Dehumidifying
Stop running
Stop heating
Original running status
Start heating
Tpreset
Tpreset
Tamb.
3mins.
Compressor
Outdoor fan
Indoor fan
Reversal valve
Anti-cool wind Anti-cool wind
Running Stopping
Under Heat mode, due to the malfunction, the compressor will stop, indoor unit will blow surplus heat.
Under this mode, the system will accord to temperature change to automatically select its running mode (Cool, Heat, Fan). The
protection function is the same with that under Cool, Heat mode. When ambient temperature has changed, firstly will switch the
mode. After compressor started up, there is no 6mins delay at least.
Under this mode, indoor fan could select High, Medium, Low and Auto running, compressor, outdoor fan and 4-way valve will
stop to run.
Under this mode, the temperature setting range is 16-30 .
When total current raise up, the frequency drop protection
When total current is high, compressor will run in limit frequnt or drop frequent; If total current exceeds the current value of unit stopping,
the compressor will stop running, outdoor fan will stop after 30s delay.
Indoor fan stops running, compressor rotate to 25Hz (mechanical frequency) running, after 75s later, outdoor fan will stop, the
4-way valve will stop running; After compressor raise frequency to the defrosting frequency for defrosting. When compressor
defrosting has 8mins, or Tout pipe 10 , compressor will turn to 25Hz running,75s later, 4-way valve will start up, outdoor
fan will start up, compressor will turn to oil return frequency for running, indoor fan will run accord with anti-cool wind condition,
the displayer board temperature will display H1 (Only for the unit, which has indoor temperature display).

Protection function in each mode
Overload protection
Compressor discharge temperature protection
Communication mulfunction
Module protection
Other control
ON/OFF
The switch status is changed one time when pressing the ON/OFF key.
Mode function
Unit will choose and display the below mode when pressing mode key: AUTO, COOL DRY, FAN, HEAT, AUTO.
TEMP. setting button
Each time TEMP or TEMP button is pressed, the set temperature will be increased or decreased by 1 . Adjusting range is 16-30 .
In AUTO mode, this button does not function.
Auto key
If controller is turned on, it will be stopped when pressing this key. If controller is turned off, unit will run with
auto and swing is running whe
Timer control
The unit is turned on or off according to the timer set by the remote controller.
Sleep function
When the air conditioner is in Cool or Dry mode, after Sleep mode has been set properly, the preset Tset will
be increased by 1 after the sleep program has run for 1 hour, and Tset will be increased by another 1 after
2hours. Tset has been increased by 2 totally in two hours. Then the unit will run at this set temperature and the
set speed.
When the air conditioner is in HEAT mode, after Sleep mode has been set properly, the preset Tset will be
decreased by 1 after the sleep program has run for 1 hour, and Tset will be decreased by another 1 after
2hours. Tset has been increased by 2 totally in two hours. Then the unit will run at this set temperature and at
the set speed.
In Fan and Auto mode, the set temperature is fixed.
Indoor fan control
Use the remote controller to set the indoor fan running at High, Med or Low speed. At this time the fan will run
at high, medium or low speed. It can also be set to AUTO
Power supply for outdoor unit
Buzzer
The controller is powered on and detect the signal received, the buzzer will beep.
When module is in protection, the compressor will stop. It will resume running after stopping for 3mins.
During the period of module protection, there will display malfunction in indoor unit and total
unit will stop running.
There have communication mulfunction when unit don't receive the corrrect signal for 3 minutes, the unit will
stop running.
When the temp. is over the standard, then compressor stop running. When the discharge temp. resume the
original conditions and compressor has stop running for 3 minutes, the compressor will resume running.
When tube temp. is detected high, the compressor runs in limited frequency or slow-frequency. When the temp. is over standard, then
compressor stop running. In auto Heat or Heat mode, the indoor fan will blow for 60s and then stop. In other modes, the indoor fan will
run at the setting speed.
Tpreset
Tpreset
Tpreset Setting temp. Tpreset
1hr. 2hrs. 2hrs. above
1hr. 2hrs. 2hrs. above
Tpreset
Tpreset
Tpreset
Setting temp. Tpreset
The method of power supply is outdoor power supply ( that is the power cable is directly conntected to outdoor unit),
the power supply of whole unit is not controlled by the controller.