Green image GC-2102DMX-RJ45 User manual

V-Type DMX Decoder
GC-2102DMX-RJ45
Type:
Project:
Catalog#:
Main Features
Specification Features
Performance Parameter
Input Voltage Operating Temperature
Load Current
Model
greenimagetech.com
105 8288 N Fraser Way
Burnaby BC, V3N 0E9
T: [phone]
F: [phone]
© Green Image Tech, LTD. All rights reserved. We reserve the right to change design, materials
and finish in a
ny way that will not alter installed appearance or reduce function and performance.
GC-2102DMX-RJ45
12-36V DC
3/4x8A
Maximum Load Power 3/4×(96-288)W
Load Type
-20 ~ +50°C
0.04-0.1 W LED type
• Highly reliable, cost-effective decoder. There are two categories;
constant voltage output and constant current output.
• Addressable and easy to address, just press the keys under the
indicator board.
• Up to 4-channel output of one decoder which can be used as RGB
(X) decoder, also can use 3 of 4 output channels as the RGB decoder.
RJ 45 port can be connected to WIFI & Bluetooth signals, RF Remote
controlled or iOS/Android programmed by WIFI.
Addressable. Address can be freely set through the digital display with
an intuitive and user friendly interface.
Three-channel / Four-channel output is selectable, per channel maximum
ouput to be 8A.
Works with the power expander to infinitely amplify output power.
1
2
3
4
Safety & Warnings
The product must be installed and serviced by qualified personnel.
IP20. Avoid direct sunlight and rain. When installed outdoors, please ensure it is mounted in a waterproof enclosure.
Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
Please check that output voltage(s) of any LED power supplies used complies with the working voltage of the product.
Never connect any cables while power is on and always ensure correct connections to avoid short circuits before turning on.
Please ensure that the cable is secured tightly in the connector.
For update information please consult your supplier.
1
2
3
4
5
6
7

Using Instruction
Connection of DMX512 decoder, please view it as below:
Seting desired DMX512 address
Use the following buttons to set desired DMX512 address: “1” sets
“hundredths” position, “2” sets “tenths” position, “3” sets “ones”.
Address cannot be more than 512.
Ensure a stable connection for the DMX512 controller to work
properly.
“3” button
“2” button
“1” button
V-Type DMX Decoder
GC-2102DMX-RJ45
greenimagetech.com
105 8288 N Fraser Way
Burnaby BC, V3N 0E9
T: [phone]
F: [phone]
© Green Image Tech, LTD. All rights reserved. We reserve the right to change design, materials
and finish in a
ny way that will not alter installed appearance or reduce function and performance.
1
2

Using Instruction
Choosing Channel(s)
Press 2nd and 3rd button at the same time for 2 seconds, digital display will flash
cH, then press 1st button to choose 1/2/3/4, each corresponds to how many
desired channels (3 creates 3 channels, and so on). Press and hold any button
for >2 seconds to confirm 1,2,3 or 4 channels. The factory preset default is 4
channel outputs.
NOTE: For example, to set address as 001. When selecting 1cH, all four
channels will be the same address (001). When selecting 2cH, channel one and
three will be the same address (001), channel two and four will be (002). When
selecting 3cH, channel 1,2,3 will be address (001,002,003), while channel 4
address is also (001). When selecting 4cH, channel 1, 2, 3, 4 will be address
(001, 002, 003, 004).
Set DMX address
Press 1st button for 2 seconds, digital display flashes to set the required
DMX address, then press any button for >2 seconds to confirm.
Choose PWM frequency
Press and hold 1st and 3rd button for 2 secs, digital display will flash to show P_c.
P means PWM frequency. To change, press the 1st button. If display reads
"1", it is at 1500Hz, "2" is at 200Hz.
C means dimming options. To change, press the 3rd button. If display reads
"1", it is using logarithmic dimming, "2" uses linear dimming.
The factory preset default is PWM frequency 200Hz with linear dimming (2_2).
Warranty Agreement
V-Type DMX Decoder
GC-2102DMX-RJ45
greenimagetech.com
105 8288 N Fraser Way
Burnaby BC, V3N 0E9
T: [phone]
F: [phone]
© Green Image Tech, LTD. All rights reserved. We reserve the right to change design, materials
and finish in a
ny way that will not alter installed appearance or reduce function and performance.
1
2
3
We provide lifelong technical assistance with this product:
• 5-year warranty. Every product has a date printed for warranty expiration (ie. 1125 means year 2011, week 25).
The warranty is for free repair or replacement and covers manufacturing faults only.
• For faults beyond the 5-year warranty, we reserve the right to charge for labour and parts.
Limited Warranty
• Any defects caused by incorrect or inappropriate operation.
• Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and replacement of chips.
• Any damages due to transportation, vibration etc. after purchase.
• Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
• Any damages caused by negligence, including storing in high temperatures, humidity or proximity to harmful chemicals.
• Product has been updated.
Repair or replacement as provided under this warranty is the exclusive remedy to the customer.