Greenfield 11203 User manual

Greenfield
POTTING BENCH
Model# 11203 Assembly Instructions
General Information:
» Read through carefully before beginning assembly.
» When assembling components, place on a clean, flat,
non-abrasive surface to avoid scratches.
» In the event of missing or defective parts, please call our
customer service department directly at 1-877-258-6020
Tools required:
» Cordless Drill with #2 phillips bit
» File or Sandpaper
» Rubber Mallet (optional)
Part # Description Qty
1 2” sq. x 48¼” Back Left Post 1
2 2” sq. x 48¼” Back Right Post 1
3 2” sq. x 38” Front Post 2
4 1½” x 4” x 46½” Table Support 2
5 1½” x 4” x 46½” Shelf Support 2
6 1½” x 4” x 20¼” Side Rail 4
8 ⅞” x 3” x 46½” Back Rail 1
9 1½” x 5½” x 46½” Back Rail 1
10 1½” x 5½” x 42½” Shelf Rail 1
11 10¾” Shelf Support Bracket 2
12 1½” x 5½” x 43” Table Top Rail 3
13 ⅞” x 1½” x 16½” Table Brace 2
14 16½” Table Top End Cap 2
15 5½” Shelf End Cap 2
16 Hardware Kit (includes):
2” sq. Post Cap 4
1¼” Kappet Screws 12
¾” Kappet Screws 48
Kappet Screw Caps 48
PVC Cement Can 1
7 ⅞” x 3” x 20¼” Table/Shelf Rail 14
Parts List:
FIGURE 1
Product dimensions &
Part identification

Insert ⅞” x 3” x 46½” back rail (part 8)
into top hole in back right post (part
2). Insert 1½” x 5½” x 46½” back rail
(part 9) into top of large hole of back
right post. Insert one table support
(part 4), into bottom of large hole of
back right post. Insert one shelf
support (part 5) into bottom hole of
right back post. Insert free ends of all
rails into corresponding holes of back
left post (part 1).
Flip over potting bench back panel,
keeping parts inserted into posts.
Using ¾” kappet screws,
screw together potting
bench back panel. Be
sure that all parts are fully
inserted into posts before
securing. Snap kappet
screw caps over screw
heads.
Insert one table support (part 4), into
top hole of one front post (part 1).
Insert one shelf support (part 5) into
bottom hole of same front post. Insert
free ends of table and shelf support
into corresponding holes of second
front post (part 1).
Flip over potting bench front panel,
keeping parts inserted into posts.
Using ¾” kappet screws, screw
together potting bench front panel.
Be sure that all parts are fully inserted
into posts before securing. Snap
kappet screw caps over screw heads.
1
2
3
4

Insert three ⅞” x 3” x 20¼” table/shelf
rails (part 7) into table support of back
panel. Insert eleven ⅞” x 3” x 20¼”
table/shelf rails (part 7) into shelf
support of back panel. Insert two
1½” x 4” x 20¼” side rails (part 6) into
back right and back left post. Insert
free ends of all rails into
corresponding holes of front panel.
Using ¾” kappet screws, screw
together potting bench. Be sure that
all parts are fully inserted into posts
before securing. Snap
kappet screw caps
over screw heads.
Lay out three ½” x 5½” x 43” table top
rails (part 12). Using 1¼” kappet
screws, insert screws through two
⅞” x 1½” x 16½” table brace (part 13).
Fasten screws to screw pilot holes of
the three table top rails. Using
PVC glue can, apply glue to
inner edges of 16½” table top
end cap (part 14). Slide end
cap onto ends of table top.
Using a file or sandpaper, file
sharp corners of end cap.
5
6
7

From behind, slide shelf through
gap in back panel of potting bench.
Using six ¾” kappet screws, fasten
wide end of brackets to
1½” x 5½” x 46½” back rail. Snap
kappet screw caps over screw
heads.
Lay out the 1½” x 5½” x 42½” shelf
rail and two 10¾” shelf suppport
brackets. Using a tape measure,
mark shelf rail 6” in from each end.
Using three ¾” kappet screws,
fasten narrow end of each bracket
to shelf rail 6” from end of shelf rail.
Shelf rail should sit on part of
bracket without screw holes. Apply
glue to inner edges of 5½” shelf
end cap (part 15). Slide end cap
onto ends of shelf rail.
8
9
Apply PVC glue to inner edges of
four 2” sq. post caps and place on
top of each post. Set table top
assembly into working area of
potting bench. The table top is
designed to be removed for easy
and quick cleaning.
10