Greenlee GATOR RK425 User manual

INSTRUCTION MANUAL
GATOR®RK425
Remote Crimping Tool
6-ton • Single-acting
52065530 REV 4 © 2019 Greenlee Tools, Inc. 9/19
Serial Number
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
Register this product at www.greenlee.com

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
2
Description
The RK425 6-ton, Single-acting, Remote Crimping Tool
is a hand-held crimping tool with removable crimping
jaws. The single-acting ram requires hydraulic pressure
to advance, and uses an internal spring to return.
This crimping tool requires an external 10,000psi
(700bar) hydraulic power source, such as Greenlee 975,
976-22, 980, 980-22, and EHP700. The RK425 may
also be powered using a hydraulic intensier capable of
developing 10,000psi (700bar), such as the Greenlee
Dynapress®intensier.
Safety
Safety is essential in the use and maintenance of
Greenlee tools and equipment. This manual and any
markings on the tool provide information for avoiding
hazards and unsafe practices related to the use of this
tool. Observe all of the safety information provided.
Purpose of this Manual
This manual is intended to familiarize all personnel with
the safe operation and maintenance procedures for the
following Greenlee tool:
RK425 Remote Crimping Tool
Keep this manual available to all personnel.
Replacement manuals are available upon request
at no charge at www.greenlee.com.
Do not discard this product or throw away!
For recycling information, go to www.greenlee.com.
All specications are nominal and may change as design
improvements occur. Greenlee Tools, Inc. shall not be liable for
damages resulting from misapplication or misuse of its products.
Dynapress and GATOR are registered trademarks of Greenlee Tools,
Inc.
Blackburn is a registered trademark of Thomas & Betts.
KEEP THIS MANUAL
Table of Contents
Description ..................................................................... 2
Safety ............................................................................. 2
Purpose of this Manual .................................................. 2
Important Safety Information ..................................... 3–4
Identication................................................................... 5
Specications................................................................. 5
Operation.................................................................... 6–7
Die and Connector Selection ......................................... 8
Maintenance................................................................... 9
Illustrations and Parts Lists .................................... 10–12

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
3
IMPORTANT SAFETY INFORMATION
SAFETY
ALERT
SYMBOL
This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury or
property damage. The signal word, dened below,
indicates the severity of the hazard. The message
after the signal word provides information for pre-
venting or avoiding the hazard.
Immediate hazards which, if not avoided, WILL result
in severe injury or death.
Hazards which, if not avoided, COULD result in
severe injury or death.
Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.
Read and understand all of the
instructions and safety information
in this manual before operating or
servicing this tool.
Failure to observe this warning will
result in severe injury or death.
Do not use this crimping tool with any hydraulic
hoses or other hydraulic components rated at less
than 10,000psi (700bar).
Failure to observe this warning will result in severe
injury or death.
Electric shock hazard:
This tool is not insulated. When
using this unit on or near energized
electrical lines, use proper personal
protective equipment.
Failure to observe this warning
could result in severe injury or death.
Wear eye protection when operating
or servicing this tool.
Failure to wear eye protection could
result in serious eye injury from
ying debris or hydraulic oil.
Skin injection hazard:
Do not use hands to check for oil
leaks. Oil under pressure easily
punctures skin. If injured, seek
medical attention immediately to
remove oil.
Failure to observe this warning
could result in serious injury, gan-
grene, or death.
Do not use solvents or ammable
liquids to clean the tool body.
Solvents or ammable liquids could
ignite and cause serious injury or
property damage.

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
4
An incomplete crimp can cause a re.
Use proper die, connector, and cable combinations.
Improper combinations can result in an incomplete
crimp.
Failure to observe this warning could result in severe
injury or death.
Pinch points:
Keep hands away from the crimping
tool head when crimping.
Failure to observe this warning
could result in severe injury or death.
Inspect tool and dies before use. Replace any
worn or damaged parts. A damaged or improp-
erly assembled tool can break and strike nearby
personnel.
Failure to observe this warning could result in severe
injury or death.
Do not perform any service or maintenance other
than as described in this manual. Injury or damage
to the tool may result.
Failure to observe this precaution may result in injury
and property damage.
Follow the operating instructions and safety informa-
tion supplied with the hydraulic power source.
Note: Keep all decals clean and legible, and replace
when necessary.
IMPORTANT SAFETY INFORMATION

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
5
Identification
Specifications
Length........................................................................................................... 12.6" (320.0 mm)
Diameter ........................................................................................................... 2.3" (58.4 mm)
Weight............................................................................................................... 2.0 lb (0.91 kg)
Crimping Force ...................................................................................................6 tons (53 kN)
1. Lock Pin
2. 3/8" Male Screw-type Coupler
1
2

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
6
Operation
Inspect tool and dies before use. Replace any
worn or damaged parts. A damaged or improp-
erly assembled tool can break and strike nearby
personnel.
Failure to observe this warning could result in severe
injury or death.
Electric shock hazard:
This tool is not insulated. When
using this unit on or near energized
electrical lines, use proper personal
protective equipment.
Failure to observe this warning
could result in severe injury or death.
Wear eye protection when operating
or servicing this tool.
Failure to wear eye protection could
result in serious eye injury from
ying debris or hydraulic oil.
Pinch points:
Keep hands away from the crimping
tool head when crimping.
Failure to observe this warning
could result in severe injury or death.
Use proper die, connector, and wire combinations.
Mismatched components can result in an incomplete
crimp. Failure to complete a crimp could result in
severe injury, death, or re if a connection separates
or if it has high electrical resistance.
Follow the operating instructions and safety informa-
tion supplied with the hydraulic power source.

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
7
Operation (cont’d)
Crimping Procedure
1. Insert conductor into the connector and align the
tool and die on the connector. Start in the center for
splices and “H” frames; and on the end, nearest the
pad, for terminals.
2. Activate the hydraulic power source until the ram
has advanced and the crimp is completed.
Note: To ensure a complete crimp, verify that the
power source has reached 10,000psi (700bar).
Refer to the “Periodic Relief Valve Check” in this
manual.
3. Stop the power source and allow the ram to retract.
4. Continue crimping the connector until the correct
number of crimps has been completed. Work from
the center to the outer edges for splices and “H”
frame connectors, alternating sides if possible, for
the best compression connections.
An incomplete crimp can cause a re.
Use proper die, connector, and cable combinations.
Improper combinations can result in an incomplete
crimp.
Failure to observe this warning could result in severe
injury or death.
Die Selection
Interchangeable dies may be used in the standard die
opening. Dies that may be used include:
• Greenlee KD6 series
• Burndy W and X series
• ILSCO ND series
• Huskie HT58 series
• Panduit CD-2001 series
• Other industry W-type dies
Installing Dies
1. Select the proper dies for the connector to be
crimped.
2. Install dies in jaws making certain that they are
properly secured by the spring-loaded, positive
lock, die buttons.
Preparing Cable
Follow the lug manufacturer’s instructions for appropri-
ate cable strip length.
Crimping Direction
First Compression
Crimping Direction
SIDE A
Crimping Direction
SIDE B
First Compression
SIDE A
First Compression
SIDE B

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
8
CJ22 Jaw and KA22/KC22-type Die Selection
Note: This tool will provide a cUL and UL classified crimp ONLY when used with the CJ22 jaws
and KA22- or KC22-type dies.
Note: This tool will provide 53 kN (6 tons) of crimping force when used with the CJ22 jaws.
Crimps made on copper cable with Greenlee KC22-type dies and the copper connectors listed here are cUL and UL classied.
Crimps made on copper or aluminum cable with Greenlee KA22-type dies and the dual-rated aluminum connectors listed
here are cUL and UL classied.
Refer to “Connector Selection” for brand names and model numbers of appropriate lugs as well as crimping instructions.
Dies for Dual-rated Aluminum Connectors
Catalog Number UPC Number Cable Size
KA22-8 06744 8 AWG
KA22-6 06745 6 AWG
KA22-4 06746 4 AWG
KA22-2 06747 2 AWG
KA22-1 06749 1 AWG
KA22-1/0 06750 1/0 AWG
KA22-2/0 06751 2/0 AWG
KA22-3/0 06752 3/0 AWG
KA22-4/0 06753 4/0 AWG
KA22-250 06754 250 kcmil
KA22-300 06755 300 kcmil
KA22-350 06756 350 kcmil
Dies for Copper Connectors
Catalog Number UPC Number Cable Size Color Code
KC22-8 03079 8 AWG Red
KC22-6 03080 6 AWG Blue
KC22-4 03081 4 AWG Gray
KC22-2 03082 2 AWG Brown
KC22-1 03083 1 AWG Green
KC22-1/0 03084 1/0 AWG Pink
KC22-2/0 03085 2/0 AWG Black
KC22-3/0 03086 3/0 AWG Orange
KC22-4/0 03087 4/0 AWG Purple
KC22-250 03088 250 kcmil Yellow
KC22-300 03089 300 kcmil White
KC22-350 03090 350 kcmil Red
KC22-400 03091 400 kcmil Blue
KC22-500 03092 500 kcmil Brown
KC22-600B 03094 600 kcmil Green
Connector Selection
CJ22 Crimping Jaw Range: Copper — 8 AWG to 600 kcmil†; Dual-rated Aluminum — 8 AWG to 350 kcmil
When used with KC22-type dies, this tool is cUL and UL classied for use with the following connector brands:
Connector
Type
Barrel
Type Anderson Blackburn®Burndy ILSCO Panduit T&B Penn- Union†
No. of
Crimps*
Copper
Splice
Short VHSS CSP YS-LsCT SCSS/SCS 54504-54518 BCU
A
Long VHS CU YSsCTL SCL/SCH 54804-54818 BBCU
Copper
Lugs
Short VHCS CTL-2/CTL
YA-2LN/YA-L/YA-2L
YA/YA-L-TC/YA-L-2TC
CSW
CRA/CRB
LCAS/LCA
LCD
54104-54118
54204-54218 BLU
Long VHCL CTL-L/LCN YA-2N
CLN/CLW
CRA-L/CRB-L
CRA-2L/CRB-2L
LCB/LCC 54930BE-54918BE
54850BE-54876BE BBLU
When used with KA22-type dies, this tool is cUL and UL classied for use with the following connector brands:
Connector Type Barrel Type Anderson Blackburn®Burndy ILSCO Panduit** T&B Penn-
Union
No. of
Crimps*
Dual-rated
Aluminum Splice — VACS ASP YS-A AS ASN SA 60501-60565 PIK
B
Dual-rated
Aluminum Lugs — VACL ATL YA-A YA-ATN
ACL/ACN
2ACL/2ACN
ALNS/ALNN/ALND
LAA/LAB 60101-60166
60230-60267 BLUA
* Use the number of crimps listed in the last column instead of the number provided with the connector:
A — 8 to 1/0 AWG: 1 crimp B — 8 to 2 AWG: 2 crimps
2/0 AWG to 600 kcmil: 2 crimps 1 to 3/0 AWG: 3 crimps
4/0 AWG to 350 kcmil: 4 crimps
** 6 AWG to 350 kcmil
† 500 kcmil maximum with Penn-Union connectors
s8 AWG to 350 kcmil with Burndy copper splices
95R7

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
9
Maintenance
• Keep the tool clean. Use the tool with care to keep dirt
and grit out of the hydraulic system. Contamination is
the most common cause of failure for hydraulic tools.
• Store the tool in its original case with the ram fully
retracted.
• Occasionally lubricate the lock pin. A molybdenum
disulde grease is recommended.
• Inspect the hydraulic hoses periodically.
• Periodically verify that the power source reaches
10,000psi (700bar). Refer to the “Periodic Relief
Valve Check” in this manual.
Periodic Relief Valve Check
Skin injection hazard:
• Do not use ngers or hands to
check for leaks.
• Depressurize hydraulic system
before servicing.
High pressure oil easily punctures
skin causing serious injury, gangrene
or death. If injured seek medical help
immediately to remove oil.
Wear eye protection when using this
tool.
Failure to wear eye protection could
result in serious eye injury from ying
debris or hydraulic oil.
Pinch points:
Keep hands away from closing dies.
Failure to observe this warning could
result in severe injury or death.
Inspect tool and dies before use. Replace any worn or
damaged parts. A damaged or improperly assembled
tool could break and strike nearby personnel with suf-
cient force to cause severe injury or death.
• Do not operate crimping tool without dies in place.
Damage to the ram or crimping tool head may
result.
• Do not perform any service or maintenance other
than as described in this manual. Injury or damage
to the tool may result.
Periodically verify that your hydraulic power source
is supplying between 9600 and 10,400 psi (662 and
717bar).
Use a test-quality pressure gauge on the supply line
from the hydraulic power source.
1. Refer to the instructions supplied with the pressure
gauge.
2. Stop the ow of hydraulic oil from the power source.
3. Connect the pressure gauge to the supply line of the
power source.
4. Install the set of test dies into the crimping tool.
5. Activate the power source until the ram has
advanced and the power source reaches relief
pressure. The pressure gauge should read between
9600 psi and 10,400 psi (662 bar and 717 bar) .
6. Release the pressure by stopping ow from your
power source. The ram will retract.
If crimp pressures are low, the hydraulic power source
relief valve may need adjustment.
Relief valve adjustments must be performed accord-
ing to the instructions provided with the hydraulic
power source.

RK425 Remote Crimping Tool
Greenlee Tools, Inc. 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
10
1
2
3
4
5
6
8
14
13
9
10
7
11
12
15
16
17
18
19
20
21
22
23
Key Part No. Description Qty Key Part No. Description Qty
1 52065902 Sheath
52049399 Spring kit (includes 2–6)
2 Bolt, shoulder ............................................ 1
3 Disc............................................................ 1
4 Compression spring .................................. 1
5 Washer....................................................... 1
6 O-ring ........................................................ 1
7 52057496 Screw......................................................... 1
8 50032631 Jaw holder................................................. 1
52049400 Latch kit (includes 9–12)
9 Compression spring .................................. 1
10 Locking pin ................................................ 1
11 Compression spring .................................. 1
12 Pin ............................................................. 1
52049401 Roller kit (includes 13 and 14)
13 Roller ......................................................... 2
14 Ram ........................................................... 1
15 52065527 Decal, ID .................................................... 1
16 52065868 Piston ........................................................ 1
17 52065869 Seal............................................................ 1
18 52065870 Cylinder ..................................................... 1
19 52065901 Grip............................................................ 1
52065823 3/8" male coupler kit (includes 20–23)
20 Seal............................................................ 1
21 Fitting......................................................... 1
22 Coupler...................................................... 1
23 Cap ............................................................ 1
52067054 Tag, connector chart ................................. 1
Illustration and Parts List—RK425