Greness Enterprise Moto-620 User manual

Moto-series
Installation Manual
Greness Enterprise Co., Ltd.
1F, 19-1. Lane39. Sec2. Jianguo South Road, Taipei 10658, Taiwan, R.O.C
TEL: [phone] FAX: [phone]
Website: www.greness.com.tw,
®Copyright 2011 Greness Enterprise Co., Ltd. All rights reserved.,
All content subjects to modificatio
n without notice.
Motorcycle / ATV Specialised Outdoor Audio System

1. Introduction
The Moto series provides everything you require to setup a complete audio system. It is specially
designed to provide the maximum outdoor music entertaining experience to the users. It offers high
quality music experiences and 4 different user-friendly means of installation. The audio system can
be installed on a variety of mobile vehicles, including motorcycles, ATV, UTV, most of the watercrafts
and
scooters
.
CONTENTS
1. Introduction ………………………………………………...……………………………………………….1
2. Applications …………………………………………………………………………………………………1
3. Safety Precaution …………………………………………………………………………………………..1
4. Specification ………………………...……………………………………………………………………...2
5. Parts list ……………………………………………………………………………………………………..3
6. Select the best location for mounting …………………………………………………………………….4
7. Amplifier Installation Manual ……………………………...………………………………………………4
8. Loudspeaker Installation Manual …………………………………………………………………………5
9. Appendix ……………………………….………………...…………………………………………………6
2. Applications
Moto series are built to withstand tough challenges in different outdoor / marine environments. They
can be installed at locations with high humidity and high chance of water splashes. Vehicles suitable
for installation include:
 Motorcycle
 All terrain vehicle (ATV)
 Personal watercraft (PWC)
 Snowmobile
 Utility task vehicle (UTV)
 Golf car
 Recreational vehicle (RV)
 Boats / yachts
1
6
3. Safety Precaution
 Read the manual before installation. It contains important information for all users.
 Turn off the main electricity supply before beginning the installation
 For electric drill, ensure it is connected to the ground properly and the area is free of any liquid.
 If any problem occurs during the installation, please contact your local dealer for advice before
pro
ceeding. Contract professionals if necessary.
9. Appendix
Item
Qnty
Description
A 1 Amplifier
B 1 Amplifier bracket
C 1 Volume control
D 1 Volume control clamp
E 2 Jet-engine speakers
F 2 Brackets (surface mount)
G 2 Clamps (handle bar mount), 7/8”
H 2 Clamps (handle bar mount), 1”
I 2 Speaker holders
J 2 Stainless steel brackets
K 2 Pan head, Phillips, type C, 4x15 mm
L 2 Pan head, Phillips, type C, 4x25 mm
M 4 Speaker nuts, 4x7mm
N 6 Pan head, Phillips, type A, 4x12 mm
O 2 Pan head, Phillips, type A, 4x6 mm
P 2 Hex nuts 4.85x3.8 mm
Q 2 Lock washers 6.3x10 mm
R 2 Lock washers 5.8x10 mm
S 4 Flat washers 6.3x10 mm
T 2 Square head bolts, 4.85x10 mm
U 2 Hex point, type A, 6.3x19 mm
V 2 Truss head, Phillips, type B, 4x13
mm, spare for plastic mount.
W 1 EPDM gasket, 50Lx15Wx1.5H mm
X 1 EPDM gasket, 82Lx15Wx1.5H mm
Y 1 Volume control, Pan head, Phillip
s,
type C, 4x25 mm
Moto-620 / 625 / 630
Moto-820 / 825 / 830
Item
Qnty
Description
A 1 Amplifier
B 1 Amplifier bracket
C 1 Volume control
D 1 Volume control clamp
E 4 Jet-engine speakers
F 4 Brackets (surface mount)
G 4 Clamps (handle bar mount), 7/8”
H 4 Clamps (handle bar mount), 1”
I 4 Speaker holders
J 4 Stainless steel brackets
K 4 Pan head, Phillips, type C, 4x15 mm
L 4 Pan head, Phillips, type C, 4x25 mm
M 8 Speaker nuts, 4x7mm
N 12 Pan head, Phillips, type A, 4x12 mm
O 4 Pan head, Phillips, type A, 4x6 mm
P 2 Hex nuts 4.85x3.8 mm
Q 2 Lock washers 6.3x10 mm
R 2 Lock washers 5.8x10 mm
S 4 Flat washers 6.3x10 mm
T 2 Square head bolts, 4.85x10 mm
U 2 Hex point, type A, 6.3x19 mm
V 2 Truss head, Phillips, type B, 4x13
mm, spare for plastic mount.
W 1 EPDM gasket, 50Lx15Wx1.5H mm
X 1 EPDM gasket, 82Lx15Wx1.5H mm
Y 1 Volume control,
Pan head, Phillips,
type C, 4x25 mm
The amplifier has auto on/off system to help saving power and has a self protective thermal fuse
device to protect both amplifier and loudspeakers from short circuiting. It is compatible with audio
devices that have an AUX-IN 3.5mm jack and the system is highly adapted to condition changes in
the environment, including humidity and temperature. Complete with waterproof accessories, the
amplifier and loudspeakers carry IP 68 rating and IP 65 rating respectively.

Figure
5
. Wiring diagram of Moto
-
8
2
0 /
M
oto
-
825 / Moto-830.
1. Red wire - Audio amplifier power (+).
Connect the red wire directly to the positive (+)
terminal of the battery.
2. Black wire - Audio amplifier ground (-).
Connect black wire to the negative (-) terminal
of the battery.
3. Grey wire - Connect the grey wire to the
positive (+) terminal of the right front speaker.
4. Grey/White wire - Connect the grey/white
wire to the negative (-) terminal of the right front
speaker.
5. White wire - Connect the white wire to the
positive (+) terminal of the left front speaker.
6. White/Black wire - Connect the white/black
wire to the negative (-) terminal of the left front
speaker.
7. Purple wire - Connect the purple wire to the
positive (+) terminal of the right rear speaker.
8. Purple/white wire - Connect the purple/white
wire to the negative (-) terminal of the right rear
speaker.
4. Specification
Moto-620 / 625 / 630
 2 Channel 40 watts waterproof outdoor Class D Amplifier for iPod / MP3 / portable CD players or
any satellite radio system
 Two jet-engine speakers including (2”/ 2.5”/ 3”for selection) with 3 different available mounting
styles
 Waterproof and corrosion-proof amplifier case with mounting bracket
 Waterproof volume control with 6fit cable and 3.5mm mini plug
 Protection :Thermal and short circuit protection and auto recovery feature
 AUX-IN 3.5 mm jack with rubber cover
 Automatically turn on power and automatically turn off power (30 - 50 seconds)
 Amplifier : IP68 rating / CE certificate / E-Mark / FCC / RoHS conformed
 Speaker : IP65 rating / IEC-268-5 (100 hrs tested) / RoHS conformed
 Frequency response : 20 Hz – 20000 Hz
 Impedance : 4 ohms
 Output power : 20W/Chennal 4 ohm load from 12V DC
30W/Chennal 4 ohm load from 24V DC
 Power supply : From 10V - 26V DC
 SNR : 98 dB / 12V 102 dB / 24V
5
2
1) Standard Flat Surface:
1. Mount the plastic bracket on the chosen flat surface with the
screws (4×12 mm) provided in the package
2. Hold the jet-engine speaker in position and secure the
mounting with a screw (4×15 mm) and a nut
3. Adjust the projecting angle of the speaker and tighten any
loose screws
2) Handle bar:
1. Select the appropriate mounting clamp from the package
2. Hold the jet-engine speaker in position and secure the
mounting to the clamp with a screw (4×15 mm) and a nut
3. clamp it around the handle bar
4. Adjust the angle of the clamp. Tighten the clamp with a screw
(4×25 mm) and a nut.
5. Adjust the projecting angle of the speaker and tighten any
loose screws
3) Mirror side:
1. Select the appropriate mounting bracket from the package and
dissemble the side mirror
2. Select the appropriate mounting style of the bracket. To
position the speakers at a higher level see depiction A; to
position the speakers at a lower level see depiction B
3. Hold the jet-engine speaker in position and secure the
mounting to the holder with a screw (4×15 mm) and a nut
4. Screw the holder to the stainless steel bracket with a 4×6 mm
screw and adjust the angle
5.
Reassemble the side mirror on the stainless steel bracket as
A
B
8. Loudspeaker Installation
Manual
Moto-820 / 825 / 830
 4 Channel 40 watts waterproof outdoor Class D Amplifier for iPod / MP3 / portable CD players or
any satellite radio system
 Four jet-engine speakers including (2”/ 2.5”/ 3”for selection) with 3 different available mounting
styles
 Waterproof and corrosion-proof amplifier case with mounting bracket
 Waterproof volume control with 6fit cable and 3.5mm mini plug
 Protection :Thermal and short circuit protection and auto recovery feature
 AUX-IN 3.5 mm jack with rubber cover
 Automatically turn on/off power and automatically turn off power (30 - 50 seconds)
 Amplifier : IP68 rating / CE certificate / E-Mark / FCC / RoHS conformed
 Speaker: IP65 rating / IEC-268-5 (100 hrs tested) / RoHS conformed
 Frequency response : 20 Hz – 20000 Hz
 Impedance : 4 ohms
 Output power : 10W/Chennal 4 ohm load from 12V DC
15W/Chennal 4 ohm load from 24V DC
 Power supply : From 10V - 26V DC
 SNR : 98 dB / 12V 102 dB / 24V
9. Green wire - Connect the green wire to the positive (+)
terminal of the left rear speaker.
10.Green/white wire - Connect the green/white wire to the
negative (-) terminal of the left rear speaker.
11. Black wire - Connect amplifier and volume control through
a black 3.5 mini plug waterproof wire and then connect to MP3
player or i-Phone.

5. Parts List
Please check the parts and their quantity before installing your audio system. Contact your local
dealer if anything is missing as soon as possible. For the list of all parts, please see the appendix
Figure 2.
Parts of
Moto
-
820
/ 825 / 830
.
Contents of all the parts included in the
Moto
-
8
20 package
Figure 1. Parts
of
Moto
-
620
/ 625 / 630
.
Contents of all the parts included in the Moto
-
620 package
6. Select the best location for mounting
Be aware that Moto series can adapt different mounting styles and each follows a separate set of
installation instructions. The loudspeakers are designed to stand on top of a strong surface. All
speakers are intended to be installed into a sturdy panel.
The surface/panel you select should have the appropriate strength to hold the unit firmly in place
after installation. Apart from the strength, consider the effects of shock, vibration, shear pressure and
movement in different directions have on the mounting surface/panel. If the surface is not sturdy
enough, the housing may be dislocated from its original position and it may be damaged. If you are
uncertain about the location of your choice, contact the local dealer for advice.
7. Amplifier Installation Manual
Read the following installation manual carefully before proceeding. If you are unfamiliar with wiring
electronic devices, consult your local dealer or contract professionals. False wiring could damage the
amplifier and the rest of audio system.
Figure
4
.
Wiring diagram of
Moto
-
62
0
/
M
oto
-
625 /
Moto-630.
1. Red wire - Audio amplifier power (+). Connect the
red wire directly to the positive (+) terminal of the
battery.
2. Black wire - Audio amplifier ground (-). Connect
black wire to the negative (-) terminal of the battery.
3. Grey wire - Connect the grey wire to the positive
(+) terminal of the right speaker.
4. Grey/White wire - Connect the grey/white wire to
the negative (-) terminal of the right speaker.
5. White wire - Connect the white wire to the positive
(+) terminal of the left speaker.
6. White/Black wire - Connect the white/black wire to
the negative (-) terminal of the left speaker.
7. Black wire - Connect amplifier and volume control
through a black 3.5 mini plug waterproof wire and
then connect to MP3 player or i-Phone.
4
3
Figure 3. Amplifier and volume control installation quick guide.
Select a stable and sturdy surface before beginning the process. Mount the amplifier unit as illustrated in the diagram (left).
For reference to volume control installation, please see right. Ensure the right parts are used during installation. For the parts
list, please see Parts List on page 3 and Appendix on page 6. Test the audio system by playing music from your audio device.
If the green light comes on then rotate the volume control knob to adjust the volume. Contact your local dealer if the system
fails to function.