Griffin Technology WS993 User manual

www.Griffin-Stands.com
Rack Mount
Rolling Stand
www.Griffin-Stands.com
www.Griffin-Stands.com
Griffin™ stands and accessories are manufactured
in several innovative factories responsible for
developing products that address the newest
needs and trends of the current market. We take
pride in the Griffin™ brand and endeavor to be on
the forefront of the musical stands and musical
and lighting accessories market.
Performance Issue, Uneven or Unstable- Make
sure all nuts and bolts are tight on the product. If they
are, then loosen all nuts and bolts 1 full turn counter-
clockwise, then go back and tighten each bolt only ½
turn tight. Then do a final tighten turn for another ½
turn tight. Next, Make sure there are not any missing
nuts or bolts. Third, ensure all parts on the product
are not broken or defective. Finally, Re-read the
assembly instructions or watch the product
demonstration video to ensure you have correctly
assembled or are using the product properly with
factory specifications.
Missing Parts- The pictures, videos and images
shown in this manual might have changed style or
count due to the product being redesigned. So in rare
cases the part may no longer be included or of a
different style. However, if you think you are missing
a part that is necessary to the assembly and use of
your product, then first carefully double check all
packaging for any parts you think are missing. Some
parts might be hiding in the packaging or loose in an
inner box.
User Manual
M o d e l # W S 9 9 3
Griffin | 11408 Hwy 64 W, Tyler, TX 75704 |
[email protected] | www.Griffin-
Stands.com
For current product specifications, please to go
www.griffin-stands.com and type the model number
into the search bar. Locate the product listing to view
the current factory specifications. Thank you for purchasing the Griffin Rack Mount
Rolling Stand. Your product comes with a 1 year
factory warranty from purchase date. Please read all
assembly instructions prior to assembling your new
cart. Pictures that may aid in assembly can be found
by going to www.griffin-stands.com and typing
WS993 into the search bar.

Step 3 –Take the
upright support bar
(Part E) and connect
to assembly done in
Step 2 as shown in
Figure 3. Once done
take the cross-
member bar (Part D)
and place near the
where the upright
support bar angles
Step 4 –Take the Right
and Left side mixer mount
bar (Part F) and the round
cross bar (Part G), connect
these as shown in Figure
4. Once done take another
cross-member bar (Part H)
and screw into the front
part of Right and Left side
mixer mount bar (Part F)
(See Figure 5).
Step 5 –Now take the piece assembled in Step 4 and
place over the piece assembled in Step 3 and secure using
a bolt screwed in the center shown in Figure 6 above.
Step 6 –Place the
knob (Part J) at the
side of the stand,
this will allow you
to adjust the angle
of the rack mount
stand to your
preference. (See
Figure 7).
Please scan the QR Code below for the product
demonstration video. Or go to the URL shown here and find
the product video. www.Griffin-Stands.com/Videos
Step 2 –Take the cross-member bar (Part B) and
connect to the bottom support bar (Part A). These has
locking clamps that fits through the holes of the bottom
support bar and fix in place with a bolt (See above
Figure 2).
Step 7 –For safety reasons, please always make sure to
test the stability and safety of the product before use.
Double check all nuts and bolts, knobs and connectors,
make sure that these are tight and securely fastened
before use of your product. Test the product under light
use or light loads the first time to confirm assembly and
structure of the product is correct.
Please note that hardware
bolts to assemble the
stand maybe screwed into
the parts themselves. So,
for example, if you are
missing a bolt that goes
into the bottom base
support tube, then look at
the end of the bottom
base support tube and
you will see that hardware
bolt is already screwed
into the stand. All you
out. Screw this in tightly and set aside.
need to do is unscrew that bolt and then screw it
back in to assemble the two parts that connect on
that end. If the stand is wobbly loosen up each bolt
on the stand slightly. Then tighten up 1 bolt all the
way as much as it will tighten. After that start on the
next bolt that is completely opposite of the 1st bolt
that you tightened. For example, if you first tightened
up the bolt in the top right of the stand, then next
start to tighten up the bolt on the bottom left. Keep
going in order of the opposite bolt that you tightened
up last. Once you are done, repeat the process of
going through and tightening up the bolts one more
time.
Step 1 –Take the bottom support bar (Part A) and screw
in the wheels provided as shown in Figure 1.