Griven GR0660 User manual

GOBOSTORM P US MK2
GR0660
Instruction manual

INDEX
1.0 Introduction ...................................................................................................................................................................4
1.1 Safety information...................................................................................................................................................................................................4
1.1.1 Prote ting against ele tri sho k................................................................................................................................................................4
1.1.2 Installation......................................................................................................................................................................................................4
1.1.3 Prote tion against burns and fire.................................................................................................................................................................4
1.1.4 Prote tion against lamp explosion..............................................................................................................................................................4
1.1.5 Weather prote tion .......................................................................................................................................................................................4
1.1.6 Prote tion against UV radiation ...................................................................................................................................................................4
1.2 Warranty onditions ...............................................................................................................................................................................................4
1.3 Complian e ............................................................................................................................................................................................................5
2.0 Size .................................................................................................................................................................................5
3.0 Components of the unit................................................................................................................................................6
4.0 Packaging and transport .............................................................................................................................................6
4.1 Pa kaging ...............................................................................................................................................................................................................6
4.2 Transport ..................................................................................................................................................................................................................6
5.0 Quick turn on.................................................................................................................................................................7
6.0 Installation .....................................................................................................................................................................9
6.1 Fixing........................................................................................................................................................................................................................9
6.2 Adjusting light beam dire tion............................................................................................................................................................................10
6.3 Conne tion to mains power................................................................................................................................................................................10
6.4 Conne tion to DMX signal...................................................................................................................................................................................13
7.0 amp installation and replacement..........................................................................................................................15
7.1 Lamp spe ifi ations ............................................................................................................................................................................................15
7.2 Lamp installation...................................................................................................................................................................................................15
8.0 Replacing gobos and focus ......................................................................................................................................17
8.1 Repla ing gobos ..................................................................................................................................................................................................17
8.2 Fo us......................................................................................................................................................................................................................18
8.3 Mounting the optional 16° Angle lens ................................................................................................................................................................18
9.0 Use of the unit..............................................................................................................................................................20
9.1 Setting operating mode .......................................................................................................................................................................................20
9.2 Unit ontrol panel .................................................................................................................................................................................................20
9.2.1 Reading the display and using ontrols ...................................................................................................................................................20
9.3 DMX Address setting ............................................................................................................................................................................................20
9.4 AUTOMATIC mode................................................................................................................................................................................................21
9.4.1 Programs exe ution....................................................................................................................................................................................21
9.4.2 Programs setting..........................................................................................................................................................................................21
9.5 Lamp setting..........................................................................................................................................................................................................22
9.6 Utility.......................................................................................................................................................................................................................22
9.7 Software release ...................................................................................................................................................................................................22
10.0 DMX function mode..................................................................................................................................................23
10.1 DMX hannels.....................................................................................................................................................................................................23
10.2 DMX fun tions .....................................................................................................................................................................................................23
10.3 DMX signal interruption ......................................................................................................................................................................................25
10.4 Lamp management by DMX signal..................................................................................................................................................................25
11.0 Master-Slave and Automatic function....................................................................................................................25
11.1 AUTOMATIC onfiguration .................................................................................................................................................................................25
11.2 MASTER onfiguration.........................................................................................................................................................................................25
11.3 SLAVE onfiguration ...........................................................................................................................................................................................25
12.0 RDM function .............................................................................................................................................................26
13.0 Maintenance.............................................................................................................................................................26
13.1 Cleaning the unit ................................................................................................................................................................................................26
13.2 Regular he ks...................................................................................................................................................................................................26
13.3 Gears lubri ation ................................................................................................................................................................................................27
14.0 Spare parts ................................................................................................................................................................28
15.0 Disposal......................................................................................................................................................................28
16.0 Message errors..........................................................................................................................................................29
17.0 Troubleshooting.........................................................................................................................................................30
18.0 Technical specifications ..........................................................................................................................................30

4 English
1.1 Safety information
1.1.1 Prote ting against ele tri sho k
• Disconnect the unit from mains supply before servicing it or performing any other action.
• Always ground/earth the unit electrically.
• Before connecting the unit to power supplies, verify that operating voltage and frequency are compatible.
• Do not handle the unit with wet hands or in the presence of water.
• Check regularly that the power supply cable is not damaged or crushed.
• Apply to a qualified technician for any regular maintenance action not described in this manual.
1.1.2 Installation
• Fix the unit with screws, hooks or any other support able to bear the weight of the unit itself.
• If the unit is fixed onto a suspended structure, this structure is supposed to bear at least ten times the weight of
all devices to be fixed.
• The unit installation actions must be performed by a qualified staff.
1.1.3 Prote tion against burns and fire
• Suitable to be installed onto normally inflammable surfaces.
• If the projector is in a fixed position and the beams is directed towards a flammable surface, the unit should be
kept at a minimum of 1 mt. If the beam is directed to people or thing at a distance lower than 2 mt, please
turn the lamp immediately off.
• The unit is not to be installed in places where the ambient temperature exceeds 35° (95°F).
• The external temperature of the unit surface (front glass) can reach 80°C (176°F).
• The lamp is very hot during operations! Wait at least for 20 minutes before changing.
1.1.4 Prote tion against lamp explosion
• Please replace any lamp that may present any damage or deformation.
• During the lamp replacement always use adequate body and eye protection (see the lamp manufacturer
instruction)
1.1.5 Weather prote tion
The unit is classified as device with an IP65 weather protection rate.
1.1.6 Prote tion against UV radiation
• Never operate the fixture with missing or damaged lenses and / or cover.
• Replace any damaged shields with original RIVEN spare parts..
• Do not stare directly into the light. Never look at an exposed lamp while it is lit.
1.2 Warranty conditions
• Each product manufactured by RIVEN srl of Italy is assembled and built in accordance to current CE con-
formity rules and regulations.
• Every single product and component has been tested before the final assembling and all products must pass
the in-house quality control before they are shipped.
• RIVEN srl of Italy guarantees the good quality and manufacture of the products and undertakes to repair or
supply again, according to his opinion and free of charge, within the shortest time possible, any part that shows
- during the guarantee period - defects of constructions, manufacture or material.
• The guarantee is valid for 12 (twelve) months starting from the delivery date of the products.
• RIVEN srl of Italy does not respond for damages occurred to the units during transport and for irrational use and
inaccuracy in regular maintenance of the products.
• The guarantee excludes all consumables.
• The customer will take care of the return of the faulty parts to RIVEN srl of Italy, at his own charge and risk.
1.0 Introduction
Warning!
This unit is suitable for professional use only, not for domestic use.

English 5
• The parts which have been repaired or replaced are sent by RIVEN srl of Italy ex-factory.
• For any dispute, the Court of Mantova (Italy) will be competent and in conformity with relevant jurisdiction the
Italian Law is enforced for any controversy.
1.3 Compliance
• Product in compliance with EN60598-1 EN60598-2-17.
• Product in compliance with 2002/95/CE (RoHS).
176mm
6,92”
368mm
14,47”
285mm
11,22”
173mm
6,81”
213mm
8,39”
2.0 Size
660mm
25,99”
715mm
28,16”
506mm
19,92”
473mm
18,62”
598mm
23,56”

6 English
Components description:
A. Front cover
B. Optic group
C. Color and gobos group
D. Electronic box
E. Ballast
4.1 Packaging
Check carefully the content of the box and, in case of damage, contact your forwarder immediately.
The following items are included in the box of this unit:
n° 1 Gobostorm Plus MK2 unit
n° 1 owner’s manual
n° 1 Ballast
n° 2 Connection kit
n° 4 obos
n° 4 Spacers 502868 for metal gobos
n° 9 Fixing springs
4.2 Transport
The carton box has not been designed to be used more than once, therefore, it is recommended to use one of
our flight cases to transport the unit.
Warning!
• Griven S.r.l. liability will cease upon consignment of goods to the forwarder: claims for damage due to trans-
port must be addressed directly to the forwarder.
• Griven S.r.l. will accept claims for broken or missing goods only within seven days of receipt of the goods.
• Returns of equipment will not be accepted without prior authorization granted by Griven S.r.l. and if not duly ac-
companied by relevant shipping documents.
3.0 Components of the unit
AB
C
D
E
4.0 Packaging and transport

English 7
In this chapter brief essential instructions for an immediate use of the unit are listed. These instructions are neces-
sary to connect and power up the unit, but they will not describe in complete details the functions of the unit it-
self. All other chapters in this manual are therefore supposed to be read, in order to learn all pieces of necessary
information relevant to the unit.
A. Open the box and check the content.
B. Install the unit.
C. Remove the screen protection “1”.
D. Install the lamp “2”.
E. Connect the ballast by using the terminal “3”.
5.0 Quick turn on
1
2
3

8 English
F. Connect the DMX signal by using the cables “4”.
G. Power up the unit by using the cable “5”.
H. Adjust the DMX address and the operating mode by using the
control panel “5” in the rear of the unit.
4
5
6

English 9
6.1 Fixing
The unit can be used both rested on floor and fixed onto a structure.
Possible mounting positions are shown in the following picture.
Use the holes Ø12.5 and Ø14 in the bracket to fix the unit.
6.0 Installation
Min 10 cm Min 10 cm
70mm
2,76in
70mm
2,76in
90mm
3,54in
180mm
7,09in
180mm
7,09in
14mm
0,55in
12mm
0,47in

10 English
6.2 Adjusting light beam direction
A. Untighten the screws "7" and the grain “8”.
B. Rotate the body of the unit towards desired direction
and tighten the screws “7” and the grain “8”.
6.3 Connection to mains power
The unit can operate with voltage from 200 to 220Vac or 230 to 240Vac and with frequency of 50 and 60Hz.
A. Untighten the screws “9” ed open the projector.
7
8
Warning!
• Before connecting the unit, verify that power supplies features are compatible with the unit features.
• The unit must never be installed if not grounded electrically.
• It is suggested to use a magnetothermic switch along the power supply line, as prescribed by in force rules.
• The unit must not be powered up through a dimmer power device.
• Wiring and connection actions are to be performed by a qualified staff.
99

English 11
Connect the ballast by using the terminal “10”.
Close the projector following the numerical order shown in
the picture.
Power up the ballast.
10
Cable n° 3
Cable n° 2
Cable n° 1
Vac IN
1
2
3
4
5
67
8
Live
Ground
Neutral
Brown
Yellow Green
Blue
Main supply

12 English
Gobostorm Plus MK2 is fitted with butt connectors and heat shrink tube which allow to perform IP67 connections.
To make the connection follow these instructions.
A. Open the bag with label “POWER SUPPLY”.
You will find inside a piece of heat shrink tube and 4 butt connectors.
B. Insert the tube “12” onto the power supply cable “11” on the
rear box of the unit.
C. Make the connection to the network by using the butt
connectors “14”, pressing them with a proper tool “13”.
D. Warm up the tube by using a heater for heat shrink tubes “15”
till the complete shrinkage.
The connection so obtained features an IP67 protection rate.
12 11
14
13
15

English 13
6.4 Connection to DMX signal
The DMX signal is to be connected by using a shielded cable designed for devices RS-485.
The signal cable must be connected according to the following table:
ND = Hose
DATA - = Black
DATA + = Red
Gobostorm Plus MK2 is fitted with butt connectors and heat shrink tube which allow to perform IP67 connections.
To make the connection follow these instructions.
A. Open the bag with label “DMX”.
You will find inside two pieces of heat shrink tube and 7 butt connectors.
B. Insert the tube “16” onto the dmx cable “17” on the side of
the rear box of the unit.
C. Make the connection to the network by using the butt
connectors “18”, pressing them with a proper tool “19”.
Warning!
All data wires must be isolated one from another and from the shield.
The GND of the DMX signal is not to be connected to the electric ground of the unit.
Insert a terminal plug with a 120 Ω resistor connected to DATA- and DATA+ in the last unit.
16
17
18
19

14 English
D. Warm up the tube by using a heater for heat shrink tubes “20”
till the complete shrinkage.
The connection so obtained features an IP67 protection rate.
If the unit which you are connecting is the last one of the DMX line, insert a 120 Ω terminal resistor connected
between DATA- and DATA+, as shown and following.
Execute stages “A” and “B”, as previously described.
C. Connect the 120 Ω resistor “21” between DATA- and DATA+
and press the butt connectors by a proper tool.
D. Heat the tube “21” by using a heater for heat shrink tubes till
the complete shrinkage and then press the final end of the
tube with a pincer “22” in order to seal the connection.
20
21
DATA-
DATA+
21
22

English 15
7.1 amp specifications
Gobostorm Plus MK2 is designed to be used exclusively with Philips MSD 575 or MSR 575 lamp.
The lamps are part of the metal halide family of discharge lamps and must be handled with great care. The lamp
operates at high pressure, and the slight risk of explosion of the lamp exists if operated over its recommended life.
We recommend, therefore, that the lamp is replaced within the manufacturer’s specified lamp life.
Every time the lamp is replaced, please reset the lamplife counter, as described in paragraph 9.5, in order to de-
termine when to perform the next replacement.
The specification of the lamp, available via the riven network of dealers and distributors, are shown in the table
below.
7.2 amp installation
A. Untighten the screws “9” ed open the projector.
7.0 amp installation and replacement
Attention!
Installing any other lamp may create a safety hazard or damage the fixture!
Lamp PHI IPS MSD 575
riven code LP0997
Rated lamp wattage 575W
Colour temperature 5700K ÷ 6000K
Luminous flux 46000 lm
Average service life 2000 h
CRI 75
Lamp PHI IPS MSR 575
riven code LP0550
Rated lamp wattage 575W
Colour temperature 6990K ÷ 7200K
Luminous flux 49000 lm
Average service life 1000 h
CRI 70
Attention!
Disconnect the unit from mains supply before servicing it or performing any other action.
The lamp is very hot during operations! Wait at least for 20 minutes before changing.
99

16 English
B. Place the lamp “23” transversally.
Close the projector following the numerical order shown in
the picture.
23
1
2
3
4
5
67
8
Attention!
Operate the units with the front panel par-
tially open for 30-40 minutes before clos-
ing them for permanent use.
This precaution will avoid the forming of
condensation in the projector.

English 17
8.1 Replacing gobos
Gobostorm Plus MK2 features a gobos wheel hosting up to 5 gobos (D Size: Ext 53,3 – Int 38).
A. Untighten the screws “9” ed open the projector.
B. Slide the metal plate “24” as shown by the arrow.
C. Remove the fixing ring “25” and proceed with the re-
placement of the gobo.
D. WARNING! The spacer 502868 "27" (provided along with
the fixture) must be placed between the metal gobos
and the gear, as shown in the picture
“25” Fixing ring
“26” METAL gobo
“27” Spacer 502868
E. Re-insert the fixing ring and put back the metal plate “24” in its original position.
24
25
8.0 Replacing gobos and focus
25
27
26

18 English
8.2 Focus
The standard beam angle is 9°. By adjusting the objective it is possible to modify the focusing.
A. Loosen the knobs “28”.
B. Act on the objective “29” to reach the desired focus .
C. Tighten the Knobs “28”.
8.3 Mounting the optional 16° Angle lens
By installing the optional lens (provided along with the fixture), the projector will achieve a 16° beam angle.
A. Undo the screws “30”.
B. Remove the objective “31”.
28
29
30
31

English 19
C. Place the lens as shown in the picture and secure it
by using the screws previously removed.
D. Loosen the screws “32” and remove the spacer “33”.
E. Install the objective “34” in its seat and perform the focusing.
Close the projector following the numerical order shown in
the picture.
32
33
34
1
2
3
4
5
67
8

20 English
9.1 Setting operating mode
By the control panel it is possible to select one of the following operating modes:
• using DMX512 signal control mode
Each fixture is controlled from DMX512 signal control.
(see chapter 10.0 DMX function)
• MASTER-S AVE or AUTOMATIC mode
The projector operates independently, without DMX512 signal control.
(see chapter 11.0 MASTER/S AVE and AUTOMATIC function)
9.2 Unit control panel
After 20 seconds of inactivity, the display will show a mes-
sage about the projector status. 3 different status can be
shown:
• DMX OFF
• DMX ON
• AUTO ON
9.2.1 Reading the display and using ontrols
MENU button:
By pushing the “MENU” button the display will show the main menu or you can exit from function and go back to
main menu.
By pushing the “MENU” button when is show the DMX address, you will enter in the main menu.
• ADDRESS SETTING
• AUTOMATIC
• AMP SETTING
• UTI ITY
• RE EASE SOFTWARE
UP and DOWN buttons:
By pushing the “UP” and “DOWN” buttons, values of the function which is shown in the display can be changed.
ENTER button:
Press “ENTER” to select, or to memorize the function which is shown on the display.
9.3 DMX Address setting
When the projector is in “AUTOMATIC” mode the menu “ADDRESS SETTING” is not visible.
Press ENTER when the display shows ADDRESS SETTING.
By using the buttons UP and DOWN select the desired value (ON or OFF) and press ENTER to confirm.
9.0 Use of the unit