Grizzly G5783 User manual

Introduction
Drill in tight places with this 3⁄8" reversible angle
drill. Producing up to 1300 RPM, this angle drill
includes a 3⁄8" Jacobs® chuck and chuck key. The
large paddle switch also makes this drill easy to
use in any position. Requires 90 PSI of air pres-
sure with 7 CFM of compressor capacity.
Inventory
A. Angle Air Drill ............................................. 1
B. Chuck Key .................................................. 1
C. Hex Wrench 3mm ...................................... 1
Operation
Insert your drill bit up to 3⁄8" into the chuck and
tighten with the chuck key. Change the drill direc-
tion by pushing the reverse valve into the body
then rotate to lock into position. Connect the drill
to your regulated air source. The hex wrench is
included for removing the screw (Ref #55) that
holds the chuck to the spindle.
MODEL G5783
3⁄8" REVERSIBLE
ANGLE AIR DRILL
INSTRUCTION SHEET
Figure 1. Model G5783.
Figure 2. Lubricating directly into air fitting.
If you need help with your new pneumatic tool,
call our Tech Support at: [phone].
COPYRIGHT © JUNE, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#PC8322 PRINTED IN TAIWAN
INJURY HAZARD!
Always disconnect tool from
air to prevent unexpected
operation during service!
EYE/EAR INJURY HAZARD!
Wear safety glasses and
hearing protection during
use of this tool!
Air drill MUST have 3-4 drops of air tool oil directly
dropped into the air fitting before each use as
shown in Figure 2. Keep the head gear lubricated
by pumping a small amount light grease into the
ball cap on the head.
DO NOT EXCEED 120 PSI!
Personal injury could
occur.

G5783 Parts Breakdown and List






 
 

















  











 
 
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 P5783001 MOTOR HOUSING 34 P5783034 BALL BEARING
2 P5783002 AIR INLET 35 P5783035 LOCK RING
3 P5783003 DEFLECTOR 36 P5783036 INTERNAL GEAR
4 P5783004 STOP RING 37 P5783037 PLANET GEAR
5 P5783005 HOUSING CAP 39 P5783039 CAGE
6 P5783006 SCREW 39-1 P5783039-1 PIN
7 P5783007 LEVER 40 P5783040 SPACER
8 P5783008 SPRING PIN 41 P5783041 GEAR SPINDLE
9 P5783009 GASKET 42 P5783042 BALL BEARING
12 P5783012 VALVE SCREW 43 P5783043 PINION
13 P5783013 O-RING 44 P5783044 GEAR
14 P5783014 VALVE BUSHING 45 P5783045 ANGLE HOUSING
15 P5783015 THROTTLE VALVE 45-1 P5783045-1 BALL CAP
16 P5783016 O-RING 46 P5783046 BALL BEARING
18 P5783018 VALVE BUSHING 47 P5783047 RETAINER RING
20 P5783020 REVERSE RETAINER 48 P5783048 SPINDLE
21 P5783021 REVERSE BUSHING 49 P5783049 KEY
23 P5783023 REVERSE VALVE 50 P5783050 BALL BEARING
24 P5783024 REVERSE SPRING 51 P5783051 BEARING CASE
25 P5783025 BALL BEARING 52 P5783052 RETAINER RING
27 P5783027 GASKET 54 P5783054 SET SCREW
28 P5783028 REAR END PLATE 55 P5783055 SCREW
29 P5783029 CYLINDER 56 P5783056 CHUCK KEY
30 P5783030 ROTOR 57 P5783057 WAVE WASHER
31 P5783031 ROTOR BLADE 58 P5783058 CHUCK KEY
32 P5783032 MOTOR PIN 59 P5783059 3/8 DRILL CHUCK
33 P5783033 FRONT END PLATE 60 PAW03M HEX WRENCH 3MM