Grizzly T30372 User manual

For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL T30372
MOUNTING KIT
FOR G0613/G0614
INSTRUCTIONS
COPYRIGHT © SEPTEMBER, 2019 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 6/19) #CS20520 PRINTED IN TAIWAN
Introduction
The Model T30372 Mounting Kit is a quick and
easy way to mount the Model T30399 Infeed/
Outfeed Roller Set onto your G0613 or G0614
Metal Bandsaw.
Description Qty
A. Extension Plate Cover ................................ 1
B. Outfeed Roller Plate ................................... 1
C. Infeed Mounting Bracket ............................ 1
D. Outfeed Mounting Bracket.......................... 1
E. Hex Bolts M10-1.5 x 25 ............................ 10
F. Flat Washers 10mm ................................. 16
G. Hex Nuts M10-1.5 ....................................... 6
H. Set Screws M8-1.25 x 8 ............................. 2
Inventory
Needed for Setup
V1.09.19
Description Qty
A. Wrenches or Sockets 17mm ...................... 2
B. Assembled Model T30399 ......................... 1
C. Model G0613 or G0614 Metal Bandsaw .... 1
D. Precision Level ........................................... 1
Figure 1. Main inventory.
A
B
C
D
F
G
Figure 2. T30372 hardware.
E
Assembly
1. Attach outfeed mounting bracket to bandsaw
base with (2) M10-1.5 x 25 hex bolts and (2)
10mm flat washers, see Figure 3.
H
Figure 3. Outfeed mounting bracket attached.

-2- T30372 Mounting Kit for G0613/G0614 (Mfd. 6/19+)
2. Attach outfeed roller plate to mounting
bracket with (2) M10-1.5 x 25 hex bolts, (4)
10mm flat washers, and (2) M10-1.5 hex nuts
(see Figure 4).
Figure 4. Outeed roller plate attached.
3. Attach infeed mounting bracket to rear vise
bracket on bandsaw with (2) M10-1.5 x 25
hex bolts and (2) 10mm flat washers (see
Figure 5).
4. Attach assembled Model T30399 outfeed
roller table and leg to outfeed mounting
bracket with (2) M10-1.5 x 25 hex bolts, (4)
10mm flat washers, and (2) M10-1.5 hex nuts
(see Figure 6).
5. Attach assembled Model T30399 infeed roller
table and leg to infeed mounting bracket
using (2) M10-1.5 x 25 hex bolts, (4) 10mm
flat washers, and (2) M10-1.5 hex nuts (see
Figure 7).
Figure 6. Outfeed roller set attached to mounting
bracket.
Figure 7. Infeed roller set attached to mounting
bracket.
6. Set extension plate cover on roller plate,
leaving roller exposed.
Figure 5. Infeed mounting bracket attached to
saw vise.
Bandsaw Vise
Brackets

T30372 Mounting Kit for G0613/G0614 (Mfd. 6/19) -3-
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
7. Tops of all rollers should be level with vise
bracket work surface. Adjust heights of tables
by loosening, adjusting, then retightening
hardware of legs and mounting brackets (see
Figure 5 & 8).
8. If rollers and vise bracket are not quite level,
insert (2) M8-1.25 x 8 set screws into mount-
ing bracket and tighten until level (see Figure
9).
Figure 8. Rollers level with vise bracket.
Vise Bracket
Work Surface
Tops of
Rollers
Figure 9. Location of leveling set screws.
1
3
5
4
2
6
7
8
9
T30372 Parts Breakdown & List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT30372001 EXTENSION PLATE COVER 6 PT30372006 ROLLER
2 PT30372002 HEX BOLT M10-1.5 X 25 7 PT30372007 OUTFEED MO UNTI NG BRACKET
3 PT30372003 ROLLER PLATE 8 PT30372008 SET SCREW M8-1.25 X 8
4 PT30372004 HEX NUT M10-1. 5 9 PT30372009 FLAT WASHER 10MM
5 PT30372005 I NFEED MO UNTI NG BRACKET