Grizzly T33905 User manual

***Keep for Future Reference***
For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL T33905
SCROLL SAW STAND
for MODEL G0969
INSTRUCTIONS
Introduction
The Model T33905 Scroll Saw Stand is specifical-
ly designed for the G0969 Scroll Saw. The stand
is made of steel, and the height can be adjusted
from 31"–38".
Inventory
COPYRIGHT © OCTOBER, 2023 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 07/23) #JM22794 PRINTED IN TAIWAN V1.10.23
Figure 1. Model T33905.
Description (Figure 2)Qty
A. Top Braces (Long) ...................................... 2
B. Top Braces (Short) ..................................... 2
C. Legs............................................................ 4
D. Bottom Braces (Short)................................ 2
E. Adjustable Leg Extensions......................... 4
F. Bottom Braces (Long) ................................ 2
G. Hex Bolts 5⁄16"-18 x 1" ................................. 4
H. Carriage Bolts 5⁄16"-18 x 1⁄2"....................... 24
I. Flat Washers 5⁄16"...................................... 32
J. Hex Nuts 5⁄16"-18 ....................................... 28
Figure 2. Inventory.
A B
C
D
E
F
G
H
IJ
To reduce risk of serious
injury, read these entire
instructions, as well as the
G0969 Scroll Saw manual,
BEFORE using scroll saw
stand.

-2- T33905 Scroll Saw Stand (Mfd. 07/23+)
•This stand was specifically designed for
the G0969 Scroll Saw. DO NOT mount
any machine but the G0969 Scroll Saw on
this stand. Doing so could cause stand to
tip or collapse, resulting in serious per-
sonal injury or property damage.
•Periodically check all fasteners and tight-
en, if necessary, prior to use.
Wear safety glasses during
the entire setup process!
Assembly
Items Needed Qty
Wrench or Socket 12mm ................................... 1
Open-End Wrenches 9⁄16" .................................. 2
Additional Person .............................................. 1
3. Attach (1) long bottom brace to (2) legs
with (2) 5⁄16"-18 x 1⁄2" carriage bolts, 5⁄16" flat
washers, and 5⁄16"-18 hex nuts, as shown in
Figure 4.
Note: Only hand tighten all fasteners for now.
You will be told when to tighten fasteners
later in these instructions.
4. Repeat Step 3 with remaining (1) long bottom
brace and (2) legs.
5. Attach (2) leg assemblies with (2) short bot-
tom braces, (4) 5⁄16"-18 x 1⁄2" carriage bolts,
5⁄16" flat washers, and 5⁄16"-18 hex nuts, as
shown in Figure 5.
To assemble scroll saw stand:
1. Remove (4) leveling feet and (8) 3⁄8"-16 hex
nuts from G0969 Scroll Saw base and install
on (4) adjustable leg extensions, as shown in
Figure 3.
2. Attach (4) adjustable leg extensions to bot-
tom of legs with (8) 5⁄16"-18 x 1⁄2" carriage
bolts, 5⁄16" flat washers, and 5⁄16"-18 hex nuts
(see Figure 3).
x 4
Adjustable
Leg Extension
(1 of 4)
x 8
Figure 3. Adjustable leg extensions attached to
legs.
x 2
Long Bottom
Brace
Legs
Figure 4. Long bottom brace attached to legs.
x 4
Short Bottom
Brace (1 of 2)
Figure 5. Leg assemblies attached with short
bottom braces.

T33905 Scroll Saw Stand (Mfd. 07/23+) -3-
6. Attach (2) long top braces to legs with (4) 5⁄16"-
18 x 1⁄2" carriage bolts, 5⁄16" flat washers, and
5⁄16"-18 hex nuts, as shown in Figure 6.
7. Attach (2) short top braces to legs with (4)
5⁄16"-18 x 1⁄2" carriage bolts, 5⁄16" flat washers,
and 5⁄16"-18 hex nuts, as shown in Figure 7.
8. Ensure stand is level, side to side and front
to back, then tighten all fasteners installed in
Steps 3–7.
Mounting Model G0969 Scroll Saw
on Stand
Tools Needed Qty
Safety Glasses (for each person).................1 Pr.
Wrenches 12mm................................................ 2
To mount G0969 Scroll Saw on stand:
1. Place stand on flat, level surface.
2. With help from an assistant, position scroll
saw on stand.
3. Secure scroll saw to stand using (4) 5⁄16"-18
x 1" hex bolts, (8) 5⁄16" flat washers, and (4)
5⁄16"-18 hex nuts (see Figure 8).
x 4
Figure 8. G0969 Scroll Saw mounted on stand.
Figure 6. Long top braces attached to legs.
Long Top
Brace
(1 of 2) x 4
Figure 7. Short top brace attached to stand legs.
Short Top
Brace
(1 of 2)
x 4

-4- Model T33905 Scroll Saw Stand (Mfd. 07/23+)
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.
T33905 Parts Breakdown & List
11
5
4
12
7
3
8
13
14
2
6
1
2
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT33905001 HEX BOLT 5/16-18 X 1 7 PT33905007 BOTTOM BRACE (SHORT)
2 PT33905002 FLAT WASHER 5/16 8 PT33905008 BOTTOM BRACE (LONG)
3 PT33905003 TOP BRACE (SHORT) 11 PT33905011 CARRIAGE BOLT 5/16-18 X 1/2
4 PT33905004 TOP BRACE (LONG) 12 PT33905012 ADJUSTABLE LEG EXTENSION
5 PT33905005 LEG 13 PT33905013 COMBO WARNING LABEL
6 PT33905006 HEX NUT 5/16-18 14 PT33905014 GRIZZLY.COM LABEL
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact [phone] or www.grizzly.com.