1
GB
Application
Can be used in conjunction with: Pressurised storage heaters,
thermally and hydraulically controlled instantaneous heaters.
Operation with low-pressure displacement water heaters is
not possible!
Specifications
• Flow pressure min. 0.5 bar / recommended 1 - 5 bar
• Operating pressure max. 10 bar
• Test pressure 16 bar
If static pressure is greater than 5 bar, fit pressure reducer.
Avoid major pressure differences between cold and hot water
supply.
• Flow rate at 3 bar flow pressure: spout 29 l/min
hand shower 16.5 l/min
• Temperature
Hot water inlet: max. 80 °C
Recommended: (energy saving) 60 °C
• Water connection cold - right
hot - left
Installation
Flush pipes thoroughly.
Installation and connection, see fold-out page I and II,
Figs. [1] to [8].
Refer to the dimensional drawing on fold-out page I.
The dimensional drawing show a form of installation
suggested by GROHE, for which no further components are
required.
Install side valves, see Figs. [1], [2] and [3].
1.Install mounting and sealing set (A1) on the side valve
shank.
2.Fasten the side valve from above using mounting and
sealing set (A2).
The distance from the side valve upper edge to the finished
surface must be 8 - 11mm, see Fig. [3].
3.Attach escutcheon (B), see Figs. [1] and [2].
4.Attach spindle & sleeve (C).
5.Connect hoses (D1) and (D2) to the side valve.
Install spout, see fold-out page II, Figs. [4] and [5].
1.Install shank with sealing set (E1).
2.Prod.-Nr. 25 064: Screw adaptor (F) to shank and attach
hoses (G).
2. Prod.-Nr. 25 065: Attach hose (H).
3.Attach spout (I) to shank, insert set screw (I1) using a 4mm
allen key.
Install diverter, see Figs. [3] and [6].
1.Install mounting and sealing set (J1) on the diverter shank,
see Fig. [6].
2.Fasten the diverter housing from above using mounting and
sealing set (J2).
The distance from the diverter housing upper edge to the
finished surface must be 8 - 11mm, see fold-out page I,
Fig. [3].
3.Attach spindle (K), see Fig. [6].
The distance from spindle (K) upper edge to the finished
surface must be 51mm. Fasten adjusted spindle (K) using
set screw (K1).
4.Attach escutcheon (L).
5.Install escutcheon hold down (M).
6.Install diverter knob (N).
7.Attach hoses (D2) from the side valve to the diverter.
8.Attach hose (H) from the spout to the diverter.
9.Attach shower hose (O).
Install hand shower, see Fig. [7].
1.Attach hose guide (P) using mounting and sealing set (P1).
2.Insert shower hose (O) through hose guide (P).
Avoid crossing the hoses!
3.Attach taper nut (Q) to shower hose (O).
4.Insert seal (Q1) into the taper nut (Q) and attach
hand shower (R) to taper nut (Q).
When using the hand shower (R), it must be ensured that
spray water does not penetrate the hose guide (P).
Flush pipes thoroughly.
Attach hoses (D1) to the existing connections, see Fig. [8].
The cold-water supply must be connected on the right and
the hot-water supply on the left.
Open cold and hot-water supply and check connections
for leakage!
Install handles, see Fig. [8].
- Grease o-ring of handle with special grease supplied.
- Install handles (18 033) or (18 034) and fasten using
set screw (S).
Maintenance
Inspect and clean all parts, replace as necessary and grease
with special grease (Prod. no. 18 012).
Shut off cold and hot water supply!
I. Headpart, see Fig. [9].
1.Loosen set screw (S) and remove handle (T).
2.Completely remove pre-mounted spindle & sleeve (C).
3.Remove escutcheon (B).
4.Unscrew extension (U).
5.Unscrew headpart (V) using a 17mm socket spanner.
II. Filter, see Fig. [10].
1.Pull out the shower hose (O) and secure against sliding
back.
2.Unscrew hand shower (R) from the taper nut (Q).
3.Clean or replace filter (Q1).
4.Remove spray hose (O).
III. Diverter, see Fig. [11].
1.Remove diverter knob cap (N1).
2.Remove nut (N2) using a 7mm socket spanner.
3.Detach diverter knob (N3).
4.Remove escutcheon hold down (M) using a 19mm open-
ended spanner.
5.Remove escutcheon (L).
6.Remove diverter (W) using a 17mm socket spanner.
IV. Remove non-return valve (X), see fold-out page III.
V. Unscrew and clean mousseur (13 927),
see fold-out page III.
Assemble in reverse order.
Replacement parts, see fold-out page III (* = special
accessories).
Care
For directions on the care of this fitting, refer to the
accompanying Care Instructions.
