Grosvenor GT10 User manual

IG-FP-GT10-R04
Connection Details
General
The GT-10 Data Collection Terminal is a
modular design which can be customised by
adding easy to install optional modules to the
terminal
Power Supply options include mains or PoE
Card Reader Module (Proximity or Swipe)
Biometric Module
Enterprise grade WiFi module
Battery option for up to 2 hours runtime
without power
Operating Temperature 0 to +45C (14 to
113F)
Humidity 5-90% non condensing
Weight 1.5Kg (3.3lb)
Power Loading - 620mA @12V Power IN
Power over Ethernet (PoE)
Module Position
Optional module enables
terminal to be powered via the
Ethernet cable using an
IEEE802.3af or IEEE802.3at
Ethernet switch or mid-span
injector
Battery Connector
For connection of the GTL Li-Ion
Battery Pack
EM-BB-2HR-A
Provides up to 2 hour runtime
Battery backup may be used with
all power options including PoE.
WARNING - ONLY FIT
BATTERY PACK SPECIFIED,
FAILURE TO OBSERVE MAY
RESULT IN FIRE HAZARD
Battery Housing
Housing for 2 or 6 hour battery
with securing strap
Ethernet Connector
10/100/1000baseT
Full duplex, auto crossover
Supports PoE (when option
module fitted)
Power IN Connector (2.1mm)
12V DC External PSU (centre
positive)12V± 5% with minimum
2A capacity (refer to Power
Loading for current calculation)
PWR Indicator
Indicates 12V power present
RESET Switch -
Press to initiate hardware
reset, Terminal will reboot
RTC Backup Battery
Real Time Clock Backup Battery
Maintains time during power
disconnection. 10 year life
Proximity Reader Module
Connector
Reader Modules include -
HID Prox and iClass
Feig Prox
Generic Prox 5V or 12V
For full list of supported
proximity modules and formats
refer to GTL website
Swipe Reader Module
Connector
Reader Modules include -
Mag Swipe
Barcode Swipe
USB Ports
Six USB2 full size sockets for
devices such as memory stick,
barcode scanner, extension
modules
USB Debug Port
For development use, allows
loading of applications
M.2 Port
Supports WiFi extension modules
Wireless Module Indicators
BT Indicator
Indicates Bluetooth Enabled
(requires supporting module)
WIFI Indicator
Indicates Wi-Fi Enabled
Memory Card Slot
Supports SD flash card
memories
Speakers (one each side)
Stereo
2W per channel
High efficiency class D amplifier
Camera and Microphone
Module
Camera and microphone may be
removed by extracting the two
screws and withdrawing the
module
Proximity Reader
Mounting Position
1 Insert the key
2 While Pressing the
key in rotate clockwise
3 Front panel bottom can
now be pulled forward
4 When separated lift
front panel to remove
Note: key cannot be removed in the unlocked position
1
2
3
4
Swipe
Reader
Mounting
Position
RECOVERY Switch
Press the Recovery button to
access the on-screen options
menu for functions including
Factory Reset
HTR Indicator
Indicates heater active, under
extreme cold conditions
integrated heater will warm unit
to minimum oprating
temperature before allowing
unit to run
C
A
B
Opening and fitting Front Panel to Back Panel
Green - 12Vin power present
Blue - PoE power present
Red- Running on battery
Front Indicators
Camera active
Application LED- Red, Green, Blue

Installing the GT-10
Secure to a Vertical Surface
Before mounting the back panel first fit any Biometric Reader options as these need access from the rear
of the unit.
Bring in any cables through snip-out apertures (A or B). Cables may be routed within the cabling cavity
between the back panel and mounting surface (C).
For installations in the USA the unit may be mounted over a power outlet with PSU (wall wart) inside the
case. For this type of installation snip-out the large aperture (B)
Fix the back panel to a flat vertical surface at a height that will be comfortable for users to see and touch
the screen observing any national regulations. Use suitable screws through any of the fixing points (D)
circled to firmly secure the device taking care to not over-tighten the screws or distort the case.
Extension Modules e.g. EM-IO-USB-IT may be fitted in the area (E)
D
DDDD
DDD
CA
B
E
Fitting Reader Modules
IT series Proximity Reader Modules may be fitted using the two mounting screws provided. Connect the
ribbon cable and apply power to the terminal.
The reader type will be automatically detected. Within the Settings menu select Readers & peripherals to
access the reader settings page.
WEEE : Please refer to www.grosvenortechnology.com for disposal instructions under EU
Directive 2002/96/EC
The default
PIN is 1905
Configuring the GT-10
With the module installed, power-up the Terminal and allow it to boot. The Terminal will detect installed modules
automatically.
To access the Settings menu allow the Terminal to boot then select ‘Admin’ . A PIN is required to enter setup mode,
the default is 1905. From the Apps menu select ‘settings’ then select ‘Readers & peripherals’.