Grosvenor RM-LUM-M320-IT/A User manual

1. GT10 Only
Feed USB cable through the
aperture in the back plate
before attaching module.
2. Fit Module to Back Panel
Slide the Fingerprint Module
into the groove in the bottom
aperture of the Back Panel as
shown below.
RM-LUM-M320-IT/A
Installation Guide
Version 1.2 May 2020
Lumidigm Biometric
Reader Module
General
The RM-LUM-M320-IT/A uses
the Lumidigm Mercury sensor, an
optical biometric ngerprint module
that uses multispectral imaging
technology.
Module Power Loading
150mA @12V Terminal Power IN
Key features include
Verify (1:1) and Identify (1:N)
modes of operation
Finger Sensor sealed to IP65
Easy installation
Simple USB Connection
The biometric ngerprint reader is
housed in a module that slots on
to the terminal back panel and is
secured in position using a single
screw.
Fitting the Reader Module
This module can be used with the GT10 (RM-LUM-M320-A) or
IT51E and GT4 (RM-LUM-M320-IT) type terminals.
Ensure the terminal is powered down and then follow the
procedure below.
Note: The RM-LUM-M320-IT/A reader can be
connected to any of the 6 USB ports found on
the IT51E/GT10 terminal front panel assembly
or any of the 4 USB ports found on the GT4
terminal front panel.
GT10 +
RM-LUM-M320-A
IT51E +
RM-LUM-M320-IT
GT4 +
RM-LUM-M320-IT
3. Secure Module with Screw(s)
The module is secured using the single screw (IT51E
& GT4) or 3 screws (GT10) provided as shown. Screw
tension should be su󰀩cient to hold module rmly but avoid
over tightening.
4. Connect Module
Feed the USB cable through the bottom aperture in the Back
Panel and connect to an available USB port inside the unit.
GT10 Only.
Fit the 2
longer screws
at the front.

Email: [e-mail]
Telephone: [phone]
Web: www.grosvenortechnology.com
Enrolling Fingers and Using the Sensor
For best results it is recommended that the equipment is
used with a ‘light/consistent touch’, i.e. the nger should
be presented in a consistent manner, with only light
pressure applied to the sensor. Research has shown
that pressing the nger hard on the sensor can reduce
the quality of a scan and this in-turn can impact on the
performance of the device.
User Capacities
When operating the Lumidigm reader in Identify mode
(1:N), the device has a capacity for 500 or 2000
depending on Terminal rmware, with 2 ngers per user.
The maximum number of users possible when operating
the device in Verify mode (1:1) is dependent upon the
terminal type and terminal memory allocation.
Fingerprint Reader Setup/Test
Once connected, the RM-LUM-
M320-IT/A module will automatically
be detected when the terminal
is powered on, no hardware
conguration is required.
It is possible to conrm the basic
operation of the module using the
Biometric/Test Sensor function that
can be found within the Terminal
Setup menus.
The Test Sensor option on the
terminal is accessible via the
following Setup menu screens:
Please note, the Calibrate Sensor
function is not supported by the
Lumidigm biometric reader
Place nger on sensor, hold in
position and after several seconds
a graphical representation of the
ngerprint should appear on the
terminal display.
Sensor Cleaning
Dampen a lint-free cloth or cotton swab with alcohol. Gently rub the cloth across the nger sensor in a left and right
direction. Move slowly down the sensor to ensure the entire surface is cleaned. Repeat this process 2-3 times.
Visually inspect the sensor surface to ensure that no residual solution remains. Caution: Abrasive cleaning uids/
materials should NOT be used to clean the nger sensor.
RM-LUM-M320-IT/A
Installation Guide