Grundfos Unilift kp 150 User manual

GRUNDFOS INSTRUCTIONS

Unilift KP 150, KP 250, KP 350

Installation and operating instructions

English (US)

English (US) Installation and operating instructions

Original installation and operating instructions

CONTENTS Page

1. LIMITED WARRANTY

Products manufactured by GRUNDFOS PUMPS

CORPORATION (Grundfos) are warranted to the

original user only to be free of defects in material and

workmanship for a period of 24 months from date of

installation, but not more than 30 months from date

of manufacture. Grundfos' liability under this

warranty shall be limited to repairing or replacing at

Grundfos' option, without charge, F.O.B. Grundfos'

factory or authorized service station, any product of

Grundfos' manufacture. Grundfos will not be liable

for any costs of removal, installation, transportation,

or any other charges which may arise in connection

with a warranty claim. Products which are sold but

not manufactured by Grundfos are subject to the

warranty provided by the manufacturer of said

products and not by Grundfos' warranty.

Grundfos will not be liable for damage or wear to

products caused by abnormal operating conditions,

accident, abuse, misuse, unauthorized alteration or

repair, or if the product was not installed in

accordance with Grundfos' printed installation and

operating instructions.

To obtain service under this warranty, the defective

product must be returned to the distributor or dealer

of Grundfos' products from which it was purchased

together with proof of purchase and installation date,

failure date, and supporting installation data.

Unless otherwise provided, the distributor or dealer

will contact Grundfos or an authorized service station

for instructions. Any defective product to be returned

to Grundfos or a service station must be sent freight

prepaid; documentation supporting the warranty

claim and/or a Return Material Authorization must be

included if so instructed.

GRUNDFOS WILL NOT BE LIABLE FOR ANY

INCIDENTAL OR CONSEQUENTIAL DAMAGES,

LOSSES, OR EXPENSES ARISING FROM

INSTALLATION, USE, OR ANY OTHER CAUSES.

THERE ARE NO EXPRESS OR IMPLIED

WARRANTIES, INCLUDING MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE,

WHICH EXTEND BEYOND THOSE WARRANTIES

DESCRIBED OR REFERRED TO ABOVE.

Some jurisdictions do not allow the exclusion or

limitation of incidental or consequential damages

and some jurisdictions do not allow limit actions on

how long implied warranties may last. Therefore, the

above limitations or exclusions may not apply to you.

This warranty gives you specific legal rights and you

may also have other rights which vary from

jurisdiction to jurisdiction.

1. LIMITED WARRANTY 2

2. Symbols used in this document 3

3. General description 3

3.1 Applications 3

3.2 Operating conditions 3

3.3 Sound pressure level 3

4. Electrical connection 4

5. Installation 4

5.1 Pipe connection 4

5.2 Basic requirements 4

5.3 Pump location and positioning 5

5.4 Adjustment of float switch 5

5.5 Non-return check valve 5

6. Operation 6

6.1 Starting 6

7. Maintenance 6

7.1 Cleaning the pump 6

7.2 Replacement of parts 7

8. Fault finding chart 8

9. Disposal 8

Warning

Prior to installation, read these installation

and operating instructions. Installation and

operation must comply with local

regulations and accepted codes of good

practice.

English (US)

2. Symbols used in this document

3. General description

Fig. 1

1. Discharge port 1.25" NPT.

2. Handle.

3. Clamp.

4. Suction strainer.

5. Outer casing.

6. Float switch (optional).

3.1 Applications

The Grundfos Unilift KP 150, KP 250 and KP 350

pumps are single-stage submersible pumps

designed for pumping grey water.

The pump is capable of pumping water which

contains a limited quantity of spherical solids up to

3/8" in diameter without being blocked or damaged.

The pump is suitable for automatic (with float switch)

as well as manual operation and can be installed in a

permanent installation or used as a portable pump.

The pump is suitable for:

• Drainage of basements or buildings prone to

flooding,

• Pumping of wastewater from washing machines,

sinks, baths, showers, etc., up to the sewer level,

• Dewatering of sites or the pumping of water for

fountains,

• Pumping in draining wells,

• Emptying swimming pools, ponds, tanks, or

fountains.

The pump is not suitable for pumping:

• sewage

• liquids containing long fibers

• liquids containing solid particles larger than 3/8"

in diameter

• flammable liquids (oil, gasoline, etc.)

• aggressive liquids.

The pump contains approx. 70 ml of non-poisonous

motor liquid that may pollute the pumped liquid if the

pump should leak.

3.2 Operating conditions

Liquid temperature

Minimum 32 °F. The maximum liquid temperature

depends on the rated voltage of the pump, see the

table below.

Storage temperature

Not lower than -4 °F.

Minimum water level

Water level must be above strainer inlet.

Maximum installation depth

30 feet below liquid level.

3.3 Sound pressure level

The sound pressure level of the pump is lower than

the limiting values stated in the EC Council Directive

98/37/EC relating to machinery.

A-weighted sound pressure level

< 65 dB(A) in accordance with ISO 3743.

Warning

If these safety instructions are not

observed, it may result in personal injury.

Caution

If these safety instructions are not

observed, it may result in malfunction or

damage to the equipment.

Note

Notes or instructions that make the job

easier and ensure safe operation.

TM03 4327 2006

Caution

This pump has been evaluated for use

with water, grey wastewater and heated

wastewater.

With float switch

Warning

Do not use the pump in or at swimming

pools, garden ponds, etc. when there are

persons in the water.

Note

If the pump has been used for very dirty or

chlorinated water it should be flushed

thoroughly with clean water after use.

Voltage Maximum liquid

temperature

1 x 115 V, 60 Hz +122 °F (+113 °F KP 350)

English (US)

4. Electrical connection

The electrical connection should be carried out in

accordance with local regulations and following the

National Electrical Code. The pump should be

grounded. The operating voltage and frequency are

marked on the nameplate. Make sure that the motor

is suitable for the electricity supply on which it will be

used.

When connecting the pump for manual operation,

the 115 V plug is inserted into a 115 V outlet. If a

float switch is included for automatic operation it will

be of the "Piggy-back" design. Plug the 115 V plug

on the float switch into the 115 V outlet, and plug the

115 V plug from the pump into the float switch plug.

Fig. 2

5. Installation

5.1 Pipe connection

Steel or rigid plastic pipe can be screwed directly into

the 1.25" NPT discharge port. For permanent

installation, it is recommended to fit a union, a non-

return valve and an isolating valve in the discharge

pipe.

Other recommendations:

• For portable or temporary installations, plastic

discharge pipe can be used in conjunction with a

suitable screwed/hose connector.

• Removal of the pump should be by a cable

secured to the pump handle and not by the

discharge pipework.

• Screwed threads should be sealed using Teflon®

tape.

5.2 Basic requirements

When the pump is installed in a permanent

installation with a float switch, and the cable length is

set to the minimum length of at least 2.5" inches, the

minimum dimensions of the well should be as shown

in fig. 3.

Furthermore, the well should be sized according to

the relation between the water flow to the well and

the pump capacity.

Fig. 3

Warning

The Unilift KP pumps have built-in thermal

overload protection and require no

additional motor protection. If the motor is

overloaded, it will stop automatically.

When it has cooled to normal temperature

it will start automatically.

TM03 4461 2106

Warning

As a precaution, the pump must be

connected to a socket with earth

connection.

It is recommended to fit the permanent

installation with a ground fault circuit

interrupter (GFCI) with a tripping current

<30mA.

115 V outlet

Float switch plug

("Piggy-back") Pump plug

Note

The pump must not be installed hanging

from the discharge pipe.

TM03 4330 2006

‹

‹‹

‹

‹‹

‹

‹‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

ø 350 mm

400 mm

16 inches

With float switch

14 inches

English (US)

5.3 Pump location and positioning

Pumps without or with float switch can be used in

vertical position with the discharge port uppermost or

in horizontal or tilted position with the discharge port

as the highest point of the pump. See fig. 4.

When used in horizontal position, the pump must be

completely covered by liquid.

Fig. 4

When the pipe/hose has been connected, the pump

is ready for use.

Before positioning the pump, make sure that the

suction strainer will not be blocked or partly blocked

by silt, mud or similar materials.

This can be avoided by positioning the pump on

bricks, an iron plate, etc. See fig. 5.

Fig. 5

5.4 Adjustment of float switch

The float switch can automatically turn the pump on

and off. Switching the adjustment is possible by

repositioning the float switch in the handle of the

pump.

The free cable length must always be:

• at least 2.5 inches

• no more than 6 inches.

Fig. 6

The start/stop level varies according to the cable

length.

For manual operation, unplug both the pump and

float switch from the 115 V outlet. Plug the 115 V

plug on the pump into the outlet.

5.5 Non-return check valve

Whenever the pump is installed in a permanent

installation with a float switch, a non return valve

must be fitted in the discharge pipe or hose.

TM00 1548 0493

Note

Do not lift the pump by means of the

electric cable. Lift the pump by means of a

cable secured to the handle of the pump.

TM00 1549 0493

‹‹‹‹‹‹‹‹

‹‹‹‹‹‹‹

‹‹‹‹‹‹

‹‹‹‹‹

‹

‹‹

‹

‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

‹‹

‹

TM03 4331 2006

Cable length

Min. 2.5" Cable length

Max. 6"

Start Stop Start Stop

Unilift KP 150

Unilift KP 250 11.5" 5.5" 12,5" 3.5"

Unilift KP 350 12" 6" 13 4"

••••••••••••••

••••••••••••

•••••••••••

••••••••••••

•••••••••••

••••••••••

•••••••••••

••••••••••

•••••••••

••••••••

Min./max.

cable length

Start

Stop

English (US)

6. Operation

6.1 Starting

Before starting the pump, check:

• whether the pump is submerged in liquid.

During normal operation, the strainer of the pump

must be below the surface of the liquid

• whether the pump is positioned on a base so that

the strainer is not blocked by silt, mud or similar

materials

• whether the pipe/hose connection is tight

• whether the discharge pipe is open (bend of

hose, etc.)

• whether the pump is connected to the electric

supply in accordance with the instructions

• check the float switch for free movement.

After start-up, check that:

• the pump operates properly, that water is being

pumped, and the pump operates through the

control sequence

• the float switch will allow the pump to pump down

to a level of approximately 4". To pump out below

this level secure the switch in the manual

position. See section 5.4 Adjustment of float

switch.

7. Maintenance

Under normal operating conditions, the pump is

maintenance-free.

If the pump has been used for liquids other than

clean water, it should be flushed through with clean

water immediately after use.

7.1 Cleaning the pump

If the pump does not deliver a sufficient quantity of

water because of sediment, dismantle and clean the

pump.

The dismantling of the pump is carried out as

follows:

1. Disconnect the electricity supply.

2. Allow the pump to drain.

3. Carefully loosen the suction strainer by inserting

a screwdriver in the recess between the outer

casing and the strainer and pressing it hard.

Repeat the procedure until the strainer is free

and can be removed, see fig. 7.

Fig. 7

4. Clean the suction strainer and refit it.

If the pump still does not deliver a sufficient quantity

of water, dismantle the pump as follows:

1. Disconnect the electricity supply.

2. Turn the pump housing 90 ° counter-clockwise

using a screwdriver, see the arrow on the pump

housing. Pull off the housing, see fig. 8.

Fig. 8

Warning

As a precaution, the suction strainer must

always be fitted to the pump during

operation.

Warning

Never dismantle the pump unless the

electricity supply has been switched off.

During dismantling, caution should be

exercised as there will be access to sharp

edges, etc. which may cut.

TM03 4329 2006TM03 1168 1205

Pump housing

English (US)

3. Clean and flush the pump with water to remove

possible impurities between the motor and the

outer casing. Clean the impeller, see fig. 9.

Fig. 9

4. Check that the impeller can rotate freely. If not,

remove the impeller:

– Slacken and remove the nut on the motor shaft

(13 mm). Prevent the impeller from rotating by

means of a screwdriver, see fig. 10.

– Clean the impeller and around the shaft.

Fig. 10

5. Check the impeller, the pump housing and the

sealing part. Replace possible defective parts.

6. Assemble the pump in reverse order of

dismantling.

7.2 Replacement of parts

The impeller assembly and electric cord can be

replaced.

The part numbers and the components included in

the service kits will appear from the tables below and

fig. 11.

If pump components other than those mentioned

above are damaged or defective, please contact

your pump supplier.

Fig. 11

TM03 1169 1205TM03 1170 1205

Note

Check before and when fitting the pump

housing that the sealing part is positioned

correctly, see fig. 11. Moisten the sealing

part with water to facilitate the fitting.

Pump type Part number

Impeller kit

KP 150, 60 Hz

KP 250, 60 Hz

KP 350, 60 Hz

015783

015784

015786

Replacement cords

10' 60 HZ

25' 60 HZ 016728

016729

Service kit Description Qty.

Impeller kit

Impeller 1

Nut 1

Gasket 1

TM03 4328 2006

Electrical

cord

Impeller

Nut

Gasket

Pump

housing

Strainer

English (US)

8. Fault finding chart

9. Disposal

This product or parts of it must be disposed of in an

environmentally sound way:

1. Use the public or private waste collection service.

2. If this is not possible, contact the nearest

Grundfos company or service workshop.

Subject to alterations.

Fault Cause

1. Motor does not start. a) Supply failure.

b) Pump switched off by float switch/vertical level switch.

c) Fuses are blown.

d) Thermal relay has cut out the electricity supply to the motor

(see section 4. Electrical connection).

e) Check cable for defects.

2. Thermal relay trips out

after short time of

operation.

a) Temperature of pumped liquid higher than that stated in section

3.2 Operating conditions.

b) Pump partly blocked by impurities (see section 6. Operation).

c) Pump mechanically blocked (see section 6. Operation).

d) Check volts and amperage.

e) Check cable for defects.

3. Pump runs but gives

insufficient water. a) Pump partly blocked by impurities (see section 6. Operation).

b) Discharge pipe/hose partly blocked. Check the non-return valve, if fitted.

c) Check the impeller, the pump housing and the sealing part (see section

6. Operation).

4. Pump runs but gives

no water. a) Pump blocked by impurities (see section 6. Operation).

b) Non-return valve, if fitted, in discharge pipe/hose blocked in closed

position.

c) Liquid level is too low. During normal operation, the liquid level must be

above the strainer.

d) Pumps with float switch: The free cable of the float switch is too long (see

section 5.4 Adjustment of float switch).

Grundfos companies

GRUNDFOS Kansas City

17100 West 118th Terrace

Olathe, Kansas 66061

Phone: (913) 227-3400

Fax: (913) 227-3500

www.grundfos.us

GRUNDFOS Canada

2941 Brighton Road

Oakville, Ontario L6H 6C9 Canada

Phone: +1-905 829 9533

Telefax: +1-905 829 9512

www.grundfos.ca

GRUNDFOS México

Boulevard TLC No. 15

Parque Industrial Stiva Aeropuerto

C.P. 66600 Apodaca, N.L. México

Phone: 011-52-81-8144 4000

Fax: 011-52-81-8144 4010

www.grundfos.mx

96637677 0117

ECM: 1199725

www.grundfos.com

The name Grundfos, the Grundfos logo, and be think innovate are registered trademarks

Other manuals for Unilift KP 150

This manual suits for next models

Table of contents

Other Grundfos Water Pump manuals

Grundfos

Grundfos BMP 5.1 RS Operating instructions

Grundfos

Grundfos SRP User manual

Grundfos

Grundfos JP6 User manual

Grundfos

Grundfos S2 Series User manual

Grundfos

Grundfos CM series Operating instructions

Grundfos

Grundfos Multilift MD User manual

Grundfos

Grundfos SQFlex 11 SQF-2 User manual

Grundfos

Grundfos COMFORT 10-16 Temperature control User manual

Grundfos

Grundfos SP User manual

Grundfos

Grundfos CHV 2 Series User manual

Grundfos

Grundfos DDC User manual

Grundfos

Grundfos UPS 25 User manual

Grundfos

Grundfos CRN MAGdrive User manual

Grundfos

Grundfos CRK Series User manual

Grundfos

Grundfos UPA 15-90 User manual

Grundfos

Grundfos MAGNA1 C Manual

Grundfos

Grundfos TP User manual

Grundfos

Grundfos HYDRO SOLO-E User manual

Grundfos

Grundfos UPA 15-90 User manual

Grundfos

Grundfos DDA 7.5-16 User manual

Grundfos

Grundfos CH 2 User manual

Grundfos

Grundfos ALPHA1 L User manual

Grundfos

Grundfos PS.W.04-20 User manual

Grundfos

Grundfos SP14-27 User manual

Popular Water Pump manuals by other brands

Watershed Innovations

Watershed Innovations HYDRAPUMP SMART FLEX Instructional manual

Graco

Graco Modu-Flo AL-5M instructions

Messner

Messner MultiSystem MPF 3000 operating instructions

Xylem

Xylem Bell & Gossett WEHT0311M Installation, operation and maintenance instructions

WilTec

WilTec 50739 Operation manual

Franklin Electric

Franklin Electric Little Giant 555702 HRK-360S instruction sheet

Ingersoll-Rand

Ingersoll-Rand PD02P Series Operator's manual

VS ZJ Series Operating instruction

Flotec

Flotec FPZS50RP owner's manual

SKF

SKF Lincoln FlowMaster II User and maintenance instructions

Xylem

Xylem Lowara LSB Series Installation, operation and maintenance instructions

Water

Water Duro Pumps DCJ500 Operating & installation instructions

Action

Action P490 Operating instructions & parts manual

Flo King

Flo King Permacore Reusable Carbon Bag Disassembly. & Cleaning Instructions

ARO

ARO ARO PD15P-X Operator's manual

Pumptec

Pumptec 112V Series Operating instructions and parts manual

Virax

Virax 262070 user manual

Neptun

Neptun NPHW 5500 operating instructions

Grundfos Unilift KP 150 User manual

Popular Water Pump manuals by other brands