Grundig SM 3330 User manual

SM 3330
EN
COMPACT JUG BLENDER
KOMPAKT STANDMIXER

4
________________________________________________________________________________
B
J
A
D
E
F
G
I
C
H
K
L
M
N

5
ENGLISH
Please read this instruction ma-
nual thoroughly prior to using
this appliance! Follow all safety
instructions in order to avoid
damage due to improper use!
Keep the instruction manual for
future reference. Should this
appliance be given to a third
party, this instruction manual
must also be handed over.
█ This appliance is intended for
private domestic use only and
is not suitable for professional-
catering purposes. It should
not be used for commercial
use.
█ The blades are very sharp!
Handle the sharp blades with
utmost care, especially during
removing and cleaning, in
order to avoid injuries follow
all instructions.
█ Check if the mains voltage on
the rating label corresponds
to your local mains supply.
The only way to disconnect
the appliance from the mains
is to pull the plug from the wall
socket.
█ For additional protection, this
appliance should be connec-
ted to a household current
fault protection circuit breaker
of no more than 30 mA. Con-
sult an electrician for advice.
█ Do not immerse the motor
housing, power cord, or
power plug in water or any
other liquids. Do not hold it
under running water. Only the
lid and the plastic jug can be
cleaned safely with water and
washing-up liquid in the dish-
washer.
█ Disconnect the power plug
after using the appliance, be-
fore cleaning the appliance or
leaving the room and if a fault
occurs. Do not disconnect the
plug by pulling on the cord.
█ Do not squeeze or bend the
power cord and do not rub
it on sharp edges in order to
prevent any damage.
█ Keep the power cord away
from hot surfaces and open
flame.
█ Do not use an extension cord
with the appliance.
█ Never use the appliance if the
power cord or the appliance
is damaged.
SAFETY AND SET-UP _______________________

6ENGLISH
█ Our GRUNDIG Household
Appliances meet applicable
safety standards, thus if the
appliance or power cord is
damaged, it must be repaired
or replaced by an authorised
service centre to avoid any
dangers. Faulty or unqualified
repair work may cause dan-
ger and risks to the user.
█ Do not dismantle the appli-
ance under any circumstan-
ces. No warranty claims are
accepted for damage caused
by improper handling.
█ This appliance shall not be
used by children. Keep the
appliance and its cord out of
reach of children.
█ Children shall not play with
the appliance.
█ Appliances can be used by
persons with reduced physi-
cal, sensory or mental capa-
bilities or lack of experience
and knowledge if they have
been given supervision or ins-
truction concerning use of the
appliance in a safe way and
if they understand the hazards
involved.
█ Do not leave the appliance
unattended while it is in use.
Extreme caution is advised
when the appliance is being
used near children and peo-
ple with limited physical, sen-
sory or mental capabilities.
█ Before using the appliance for
the first time, clean all parts
which come into contact with
food carefully. Please see
details in the “Cleaning and
Care” section.
█ Never operate or place any
part of this appliance on or
near hot surfaces such as a
gas burner, hotplate or heated
oven.
█ Do not use the appliance for
anything other than its inten-
ded use.
█ Never use the appliance in or
near to combustible or inflam-
mable places and materials.
█ Operate the appliance only
with the delivered parts.
█ Do not use the appliance with
damp or wet hands.
SAFETY AND SET-UP _______________________

7
ENGLISH
█ Never place the appliance,
attachments, power cord or
plug on hot surfaces such
as gas or electric burners or
hot oven surfaces and never
use it with hot liquids or food.
Let hot food and liquids cool
down to min. 80°C or less,
before using the appliance.
█ Always use the appliance on
a stable, flat, clean, dry and
non-slip surface.
█ Make sure that there is no
danger that the power cord
could be accidentally pulled
or that someone could trip
over it when the appliance is
in use.
█ Position the appliance in such
a way that the plug is always
accessible.
█ The blade unit is very sharp!
Handle the blade unit with ut-
most care, especially during
cleaning, in order to avoid
injuries.
█ Do not use the appliance if
the blade unit is damaged or
shows signs of wear.
█ Never clean the appliance
with your bare hands.
█ Never try to use the appliance
without the lid.
█ Do not attempt to remove the
lid until the blades have com-
pletely stopped.
█ A spatula may be used to
remove the ingredients from
the plastic jug. The appliance
must be switched off before
doing this.
█ Never operate the appliance
for longer than necessary for
processing the food.
█ Remove bones and stones
from food to prevent the blade
unit and the appliance from
being damaged.
█ This appliance is only inten-
ded for short periods of use
and should only be in con-
tinuous use for maximum 1
minute. After use, let the appli-
ance cool down sufficiently.
█ Do not crush ice cubes.
█ Switch off the appliance and
disconnect from supply before
changing accessories or ap-
proaching parts that move in
use.
SAFETY AND SET-UP _______________________

8ENGLISH
AT A GLANCE _____________________________
Dear Customer,
Congratulations on the purchase of your new
GRUNDIG Compact Jug Blender SM 3330.
Please read the following user notes carefully to
ensure full enjoyment of your quality GRUNDIG
product for many years to come.
A responsible approach!
GRUNDIG focusses on contractu-
ally agreed social working condi-
tions with fair wages for both
internal employees and suppliers.
We also attach great importance
to the efficient use of raw materials
with continuous waste reduction of several tonnes
of plastic every year. Furthermore, all our acces-
sories are available for at least 5 years.
For a future worth living.
For a good reason. Grundig.
Controls and parts
See the figure on page 3.
A Cap
B Cover opening
C Cover
D Plastic jug
E Mixer blade device
F Motor housing
G Slow speed button
H High speed button
I Non-slip feet
J Cable reel
K Chopper
L Beaker blade device
M Cover for shredder
N Filter

9
ENGLISH
Preparation
Caution
█ Switch off the appliance and disconnect from
supply before changing accessories or ap-
proaching parts that move in use.
1 Remove all packaging and sticker materials
and dispose of them according to the appli-
cable legal regulations.
2 Take the entire unit of the motor housing F
and place it on a level surface, e.g. on the
kitchen counter.
Caution
█ The blade unit is very sharp! Handle the blade
unit with utmost care, especially during clean-
ing, in order to avoid injuries.
3 Clean all parts, with the exception of the
motor housing F as described in “Cleaning
and Care”.
4 Then re-assemble the jug blender in the re-
verse order.
5 Put the plastic jug D on the motor housing F.
Note
█ Make sure that the notches on the bottom of
the plastic jug D fit those in the motor hous-
ing F.
Blending
1 Place the device on an even and dry surface.
The non-slip feet I ensure the stability of the
appliance.
2 Make sure that the power cord is discon-
nected from the power supply.
3 Remove the plastic jug D from motor housing
F; to do this, turn the plastic jug D in an anti-
clockwise direction and lift it upwards; open
the cover C.
4 Now put the ingredients to be blended in the
plastic jug D. The ingredients should only be
about 2-5 cm long.
Notes
█ Add water to ensure the jug blender functions
smoothly.
█ Mix 3 units of hard food and 2 units of water
in order to have a smooth jug blender experi-
ence. (i.e: 60 gr hard food 40 ml water)
Caution
█ Do not put or blend hot food or liquids in the
plastic jug D. If you process soup, make sure
that the liquid temperature does not exceed
40°C.
█ Never let the jug blender operate while empty
(without food).
█ Never let the jug blender operate without the
plastic jug on the motor housing F.
5 Close the cover C. Ensure that the cap A is
located and secured in the cover opening B.
To close, turn in a clockwise direction.
6 Place the plastic container D upright on the
motor housing F and turn in a clockwise di-
rection.
Caution
█ Never move or turn the plastic jug after it is
properly seated in the place.
7 Connect the power plug to a suitable power
outlet.
8 Press the required cutting speed G or H.
Notes
█ To operate the blender at the low speed, turn
the control dial to “1”.
█ To mix at a high speed, press the speed regula-
tor H to “2”.
█ To add ingredients during operation: Add the
ingredients through the opening in the cover
C. To do this, turn the cap C in an anti-
clockwise direction and remove.
Caution
█ Never run the blender for longer than 1 minute,
otherwise it would overheat.
█ After running the appliance for 1 minute, let it
cool down before using it again.
OPERATION ______________________________

10 ENGLISH
█ Be sure the motor is switched off and has com-
pletely stopped before removing the plastic jug
D from the motor housing F.
█ Do not place any utensil (scraper, fork, etc.)
in the glass jug while the blender is operating.
9 Pull the power plug out of the power outlet.
10 Remove the plastic container D from the
motor housing F ; to do this, turn the plastic
container D in an anti-clockwise direction.
11 Take off the lid and pour the mixture into
glasses or other containers.
Maximum quantities and
processing time
█ See table with maximum quantities and proces-
sing time.
Ingre-
dients
Maximum
quantities
Processing
time
Fruit 100 - 200 g 20 - 30
Seconds
Fruits 100 - 200 g 20 - 30
Seconds
Fruit juice 100-200 g Fruit +
Water (optional)
20 - 30
Seconds
Milkshake 100 g Fruit +
300 ml Milk
20 - 30
Seconds
Shredder
Caution
█ Liquid food is not suitable for use of chopper
K.
█ The chopper K is suitable for ingredients such
as meat or onions.
1 Cut ingredients into 1-2 cm pieces and add to
the container.
2 Position the beaker blade device, L on the
beaker by turning it in an anti-clockwise direc-
tion.
3 Position the beaker upright on the motor hous-
ing by turning it in a clockwise direction.
4 Connect the power cable to a suitable socket.
5 Press the required cutting speed.
6 Open the blade device L by turning it in a
clockwise direction.
Filter (optional)
█ You can also grind fresh coffee with the filter
N.The filter ensures that the beans are col-
lected quicker and that they are more finely
ground.
█ You can also use the filter N to prepare
refreshing fruit juices, cocktails, or soya milk.
The filter ensures that the juice remains free of
seeds.
1 Add the coffee beans to the filter N.
2 Place the filter N in the plastic container.
3 Put on the cover C.
4 Place the plastic container D upright on the
motor housing F and turn in a clockwise di-
rection.
OPERATION ______________________________

11
ENGLISH
INFORMATION ___________________________
Tips for blending
█ To add food while the blender is operating,
remove the cap A and drop the ingredients
through the opening. Be sure to cut the food
into about 2-5 cm pieces to fit through the
opening. Replace the cap A when you have
finished adding ingredients.
█ When blending solid food, such as raw veg-
etables, cooked or uncooked meat and fruits
always cut them into no larger than 2-5 cm
pieces before placing them into the plastic jug.
Blend no more than 2 cups of these food at a
time. This will speed the blending process and
reduce wear on the blending blades.
█ Always place liquid ingredients in the plastic
jug first, unless a recipe specifically states oth-
erwise.
█ To blend beverages, place all ingredients in
the plastic jug at the same time.
█ Avoid overblending. Usually, you will need to
blend for a few seconds.
█ Overblending may cause food to become
mushy.
Cleaning and care
Caution
█ Never use petrol, solvents, abrasive cleaners,
or metal objects and hard brushes to clean the
appliance.
█ The blades of the cutter unit are very sharp!
Handle the blades with utmost care in order to
avoid injuries.
█ Never clean the appliance with your bare
hands.
█ Clean the jug blender after each use. Do not
let any food remnants harden on and inside
the jug blender. This will make it more difficult
to clean it later.
█ Do not use boiling water. The blade assembly
bearings have been designed with a lifetime
lubricant; exposure to boiling water may dam-
age these bearings and shorten the life of the
blender.
1 Turn the appliance off and disconnect it from
the wall socket.
2 Allow the appliance to cool down.
3 Remove the plastic jug D from the motor hous-
ing F. Rinse with water to remove any large
food particles that may have accumulated in
the plastic jug.
4 Replace the plastic jug D on the motor
housing F.
5 Place 1 to 1 ½ cups warm water with some
drops of mild cleanser into the glass jug D
and switch to speed “2” for a few seconds.
Remove the plastic jug from the motor housing
F and rinse with water. Repeat as necessary.
Note
█ Do not immerse the motorized base or blade
unit in liquid, or place them in the dishwasher.
Only the lid and the plastic jug may be im-
mersed and placed in the dishwasher.
6 Use a damp soft cloth and some mild cleanser
to clean the exterior of the appliance.
7 Wipe the blender base, cutter unit F and lid
with a lint free cloth before the next usage.
Storage
If you do not plan to use the appliance for a long
period of time, please store it carefully. Make sure
the appliance is unplugged and completely dry.
Store the appliance in a cool, dry place. Make
sure the appliance is kept out of the reach of chil-
dren.

12 ENGLISH
INFORMATION ___________________________
Environmental note
This product has been made from high-quality
parts and materials which can be re-used and
are suitable for recycling.
Therefore, do not dispose the product
with normal household waste at the
end of its service life. Take it to a col-
lection point for the recycling of elec-
trical and electronic equipment. This is
indicated by this symbol on the product, in the
operating manual and on the packaging.
Please consult your local authorities to find out
where the nearest collection point is.
Help protect the environment by recycling used
products.
Technical data
This product conforms to the Euro-
pean directives 2004/108/EC,
2006/95/EC, 2009/125/EC and
2011/65/EU.
Power supply: 220 - 240V~, 50/60 Hz
Power: 350 W
Technical and design modifications reserved.

Grundig Intermedia GmbH
Beuthener Strasse 41
D–90471 Nürnberg
www.grundig.com
72011 909 5900 15/28