GSM Activate SWV2G-RS2 User manual

GSM 2G/3G 240V
ROLLER SHUTTER OPENER
No More Key Fobs! Open roller shutters with your mobile phone
www.gsm-activate.co.uk
Page 1
MODEL NUMBER SWV2G-RS2

Page 2
Product Information
The GSM Roller Shutter/Opener incorporates a professional industrial grade GSM engine
that receives calls at its SIM number as any ordinary mobile phone. The system operates
in the GSM module quad-band frequency 850/900/1800/1900Mhz.
Just to give an example, if your SIM has a phone number 07123456789, that is the
number you have to call to open the shutter door. The system has a memory where you
will store the numbers of people enabled to open your shutter (up to 50).
When the Roller Shutter/Opener receives a call it will check the calling number and if the
number is in the prepared list it will answer the call. You then use your telephone keypad
to open and close the roller shutter.
The advantages of this over other systems are that you do not have to leave your car to
open the shutter therefore, avoiding weather or safety issues. Furthermore, you do not
need to carry a separate remote device or indeed replace it if it were to be lost.
Specification
●Simply dial the simcard number to open the gates/shutter door.
●Phone list for added security up to 50 stored numbers.
●Text for signal strength.
●Call and use keypad to move shutter up or down.
●Antenna supplied.
●Sim Active Function
●Dimensions - L150 x W90 x H45mm
●Dimensions - L125 x W67mm
●INPUT 240VAC
●Output Relays are 10 AMP N/O or N/C Volt Free
●Quadband Frequency - 850/900/1800/1900Mhz
●No need to keep replacing remote keyfobs when the keyfobs are lost!

INSTRUCTIONS
IMPORTANT- PLEASE READ
PLEASE MAKE SURE YOU DISCONNECT THE POWER WHEN YOU FIT THE
SIMCARD AND YOU PLACE THE SIMCARD WITH THE CLIPPED CORNER FACING
OUT WARDS.
PLEASE SEE PICTURE ABOVE.
1: First you must register and put credit on your simcard. Please follow the instructions
given with your simcard
2: Insert the simcard into a mobile phone and disable the voicemail using the codes
below
Vodaphone: call 1210 Tesco call 2915
T-Mobile: call 222 O2 call 1760
Orange: call 4502 Giff Gaff call 1626
EE - send the text message command VM OFF to 150
3: Refer to steps 1 - 4 in Fig 1 above
Important Notice
You must remove the PIN request from the SIM before inserting it into the unit otherwise
the device will not work. In order to do so, insert the SIM in a phone and disable the PIN
request.
1. Slide back the sim door and lift it up.
2. Slide the simcard into the door making sure that the clipped corner of the simcard lines
up with the clipped corner of the simcard holder.
3. Close the simcard door.
4. Slide the simcard door to lock the simcard in place.
When you first switch the unit on, the blue LED will flash
The blue LED will continue to flash until the unit is ready then the green LED will come on.
Page 3

Page 4
How to program the roller shutter opener.
Text message entry
You must first enter the telephone numbers that are authorized to use the Roller shutter
opener. Insert your simcard into the Roller Shutter opener and turn on the unit and wait
until you receive a steady green light this will indicate that you have a mobile signal.
You will now need to send a text with the contact numbers.
Example: (Hash) (WHL) (Hash) (phone number) (hash)
To avoid confusion we have colour coded the hash (#) and the star (*) symbols.
#WHL#07123456789# Then send this as a text to the simcard
NOTE
PLEASE NOTE YOU CAN ONLY SEND ONE NUMBER AT A TIME. (Max 50 numbers)
PLEASE SEND THE TEXT MESSAGE AND WAIT FOR THE ROLLER SHUTTER
OPENER TO SEND YOU BACK THE TEXT ACKNOWLEDGEMENT “STORED” BEFORE
YOU TRY TO ADD ANOTHER NUMBER VIA TEXT ENTRY.
If you do not need authorized numbers you can turn Dip switch 1 to the OFF position as in
fig.1. This will allow any number to operate the roller shutter if they call the simcard number
used inside the unit. Automated calls will not be able to operate the unit as they would be
unable to use the keypad commands.
If you wish to cancel a number follow this example.
(Hash) (delete) (Hash) (NUMBER) (Hash)
#Delete#07123456789# Deletes the stored number
Please make sure you have credit on your simcard to receive the text acknowledgment.
It may take a time to receive a text acknowledgement. This depends upon how busy your
telephone network is.

Page 5
How to use the Roller Shutter Opener
Using your mobile phone or landline, dial the simcard number within the unit. You will hear
two ring tones. The unit will then answer the call. Once the call is open you can use the
keypad on your phone to operate the device.
Press key 1 - Relay 1 will pulse
Press key 2 - Relay 2 will pulse
Pushing key number 1 or 2 again will stop the command and the shutter will hold in a
stationary position.
We recommend connecting relay 1 to OPEN/UP and relay 2 to CLOSE/DOWN on your
roller shutter control board.
When you press 1 you will hear a fast dialling tone.
When you press 2 you will hear a slower dialling tone.
Please view the diagram on page 6 for wiring information.
Latching Relay - Deadmans Button
This function is used for roller shutter control boards whereby you need to manually hold
the button to open or close the roller shutter. Once you remove your finger from the button
the roller shutter will stop the operation your are performing.
To use the roller shutter opener in this mode (latching relay) you need to put dipswitch 2
to the ON position. The relay will now latch on for 15 seconds instead of pulsing.
Pressing key 1 will cause relay 1 to pulse to open for 15 seconds
Pressing key 2 will cause relay 2 to pulse to close for 15 seconds
Pressing key 3 will cancel the command and stop the shutter.
Signal Strength
To help make sure that you place the unit in a suitable position you can text the unit to see
how much signal strength the dialler is receiving by texting the command
#SIGNAL
The unit will perform a test on the signal strength.
You will receive a text telling you the signal strength score between 0-30. We strongly
recommend that you place the unit where you will receive a score of at least 10. You will
find that a signal strength score of less than 10 will make the unit unreliable.
Factory Reset
To perform a quick factory reset which will delete ALL of your stored numbers please send
the text command
#RESET
The red LED will flash 6 times indicating that the reset has been successful.

For more technical support please browse the FAQ’s on our website www.gsm-activate.co.uk
Alternatively email our technical support team at technica[email protected] and we will
do our best to reply within 24 hours Monday - Friday.
Page 619/09/19 GD
Using your mobile phone or landline phone, dial the simcard number within the unit. You
will hear 2 ring tones then the unit will answer the call. Once the call is open you can use
your phone keypad to operate the roller shutter.
Press key 1 will cause the relay to pulse
press key 2 will cause the relay to pulse