GST I-9201 User manual

30308433 Issue 1.02
Features
Electronically addressed. Address can bemodified
in field.
Built-in microprocessor processes information
intelligently.
Reusable button can be reset manually.
Providing an independent output contact.
Plug-in structure.
Description
I-9201(T) Addressable Manual Call Point with FT Jack
(MCP) is installed in public places. When there is a fire,
pressing the nearest MCP, alarm signal can be sent to
the fire alarm control panel (FACP). And the FACP will
show the address of the MCP, and give alarm sound.
Person in field can communicate with person at fire
telephone panel by plugging his handset of P-9912(A)
or P-9912(B) into this FT jack.
The MCP is operated by pressing the mechanically
latched button to reduce possibility of accidental alarm.
The built-in microprocessor can execute alarm
checking and communication with the control panel.
The microprocessor contains an EEPROM to store
messages like address and device type.
Connection and Cabling
Fig.1 shows terminals of the MCP.
Conduit
Mounting
Hole
65mm
Fig.1
Connection:
Z1, Z2: Loop connection, polarity-insensitive.
K1, K2: Volt-free normally open output contact. The
closed contact signal shall be output when the MCP is
pressed to directly control external devices.
TL1, TL2, AL, and G: Connecting with I-9304
Emergency Telephone Module or Fire Telephone
Panel.
Recommended Cabling:
1.0 mm2 or above fire cable for all cables. Subject to
local codes.
Installation
Unplug the MCP, thread the cable through the wiring
hole of the base box and connect it to corresponding
terminals, and plug the MCP back. The base of the
MCP can be surface mounted or flush mounted as
shown in Fig.2 and 3.
YM-02C Back Box
Conduit
Back Box
MCP Conduit
MCP
Fig.2 Fig.3
Warning: Before installing the MCP, disconnect the
power from the loop and verify that all bases are
securely installed and that the wiring polarity is
correct at each base.
Application
Connect the terminals Z1 and Z2 to the loop of control
panel directly. If connected with multi-wire fire
telephone panel, only TL1 and TL2 are needed. If
connected with addressable fire telephone panel, TL1,
TL2, AL and G are needed.
Before operation, the MCP should be
programmed by programmer. Please refer to
P-9910B Hand Held Programmer Installation and
Operation Manual for details.
If the connection and wiring are correct, the
control panel should be able to register the MCP.
When fire occurs, pressing the glass on the MCP,
the LED should flash quickly and the control
panel should display fire alarm message.
Please reset the MCP in time when fire alarm is
disposed.
The Intelligent Solution
I-9201(T) Addressable
Manual Call Point with FT Jack

30308433 Issue 1.02
Specification
Operating Voltage
Loop 24V (16V~28V)
Standby Current
≤0.6mA
Alarm Current
≤1.8mA
Indicator
Red, flashes every 3
seconds in polling and
illuminates in alarming
Output Capacity
Rating 60VDC/100mA;
Volt-free output contact
signal;
contact resistance≤100mΩ
Type of Initiating
Part
Reusable
Initiating Mode
Pressing the glass manually
Reset Mode
Manually reset by a sucker
Program Mode
Electronically addressed
Programming
Electronic programming one
address within 1～242.
Wiring
Non-polarized signal loop for
FACP, Four-wire with
emergency telephone Jack
and two-wire with fire
telephone panel.
Ingress Protection
Rating
IP43
Environment
Temperature
-10℃～+50℃
Relative Humidity
≤95%, no condensing
Material and Color
of Enclosure
ABS, Red (PANTONE 185C)
Dimension
90mm×122mm×48.5mm
(with base)
Mounting Hole
Distance
65mm
Weight
About 221g (with base)
Accessories and Tools
Model
Name
Remarks
P-9910B
Hand Held
Programmer
Order separately
YM-02C
Back Box
Order separately
Limited Warranty
GST warrants that the product will be free from defects
in design, materials and workmanship during the
warranty period. This warranty shall not apply to any
product that is found to have been improperly installed
or used in any way not in accordance with the
instructions supplied with the product. Anybody,
including the agents, distributors or employees, is not
in the position to amend the contents of this warranty.
Please contact your local distributor for products not
covered by this warranty.
GST China
Gulf Security Technology Co., Ltd.
No. 80, Changjiang East Road,
QETDZ, Qinhuangdao, Hebei,
P. R. China 066004
Tel: [phone]
Fax: [phone]
sales.gs[email protected].com
www.gst.com.cn
GST UK
Global System Technology PLC
Lion Court, Staunton Harold Hall,
Melbourne Road, Ashby de la Zouch,
Leicestershire, England LE65 1RT
Tel: [phone]
Fax: [phone]
[e-mail]
www.gst.uk.com
GST Dubai
Global System Technology PLC
P.O. Box 17998 Unit ZA04
JEBELALI Free Zone,
Dubai, UAE
Tel: [phone]
Fax: [phone]
[e-mail]
www.gst.uk.com
This document is subject to change without notice. Please contact GST for more information or questions.