Guest Internet GIS-R3 User manual

GIS-R3 connections
Hotspot Gateway Product Setup - Quick Start Guide 1
The Guest Internet Hotspot gateway products have
Ethernet LAN ports that can be used to connect wireless
access points, Internet café ios computers, wired
hotel rooms and business center computers. The
Internet (WAN) port must be connected to the DSL or
cable modem
First Time Product Configuration
Connect your laptop computer to one of the LAN ports of the gateway.
Connect the Internet port to your DSL router.
Open your computer browser. Instead of your login page you will see the
page shown below. This page is the SETUP WIZARD.
Connect your computer
Ethernet connector to the
LAN1 connector of the
gateway. Your computer
Ethernet connector should
be configured for dynamic
IP or as a DHCP client. It
cannot be used with a
fixed IP.
Download the product manual at: http://www.guest-internet.com/gateway
First connect the gateway
as shown in the diagram
to configure it using the
setup wizard.
Connect the Internet connector of the
gateway to the DSL or cable modem LAN
DSL
Or
Cable
Internet
Configuration
computer
Product
Configuration
WA
Internet port
LA port
GIS-R3
12volt power supply
For 110/220volts
WA
DSL/Cable router
Wireless
access
points
The setup process has four steps. Follow the instructions to type in the
information requested on each page. Then clic on the button to go to the
next page. When the setup process is completed your personalized
wireless Internet service will be ready for your guests to start using. The
setup process is shown overleaf: flip this page over to start the setup
process.
Login to the Admin pages at any time. Connect your computer to the
gateway via an Ethernet cable to a LAN port. Then open your browser and
type in the URL:
http://aplogin.com/admin
The username is admin , and the password is the one that you entered
with the wizard.
When the page opens select the option you need in the menu. See the
manual for more information about configuration.
For operation the WiFi Hotspot users will use
the wireless networ or ios computers.
Connect wireless access points and ios
computers to the gateway LAN ports.
Reset to Factory Defaults:With the gateway powered up, use a paperclip to press the reset button
through the hole shown. Hold the reset button down for 10 seconds then release. All parameters will be reset.
gateway to the DSL or cable modem LAN
Ethernet connector. The DSL of cable
modem should have the LAN networ
connector configured as a DNCP server.
Chec with the equipment manual to verify
the LAN connector configuration.
If you wish to connect more devices then
connect an Ethernet switch to one of the LAN
ports.
Copyright © Fire4 Systems Inc., 2012. All rights reserved.
[e-mail]
Reset
USE NLY THE P WER SUPPLY SHIPPED
WITH THE UNIT T PREVENT DAMAGE
D N T DISC NNECT P WER
DURING RESET T AV ID DAMAGE

Your gateway unit must have a connection to the
Internet for the configuration process to be completed. If
you see a green YES then proceed to step 2. If a red NO
then clic on the lin to diagnose the problem.
You may have to set a ‘fixed IP’. If you are not familiar
with setting a fixed IP then as a networ technician to
provide help with this.
Some DSL and Cable routers have a firewall setting that
prevents the gateway from connecting to the Internet.
You may have to change a setting on the router firewall.
Step 2: configure hotspot settings
Select your time zone and set your password. Note your
password and eep in a safe place.
If you select unlimited access then your guests will clic
on a disclaimer to access the Internet. If you select
controlled access then you will have to generate access
codes for your guests.
Step 1: test the Internet access Step 4: select guest access
Hotspot Gateway Product Setup - Quick Start Guide 2
Download the product manual at: http://www.guest-internet.com/gateway
Finished, click on reboot to start your hotspot
Your guests will see this information on the login page After reboot wait two minutes then open your browser
to see your login page. If you want to ma e changes
then login again and clic on the setup wizard.
Step 3: login page branding
Copyright © Fire4 Systems Inc., 2012. All rights reserved.
[e-mail]