GunVault SVB 500 User manual

SpeedVault Biometric
Model SVB 500
User Manual
Patented Rev 1 (10/11)

- 1 -
Firearm Safety
WARNING: The SpeedVault Biometric safe or any other firearm storage device cannot
take the place of other safety procedures including advising children of the dangers
of firearms.
WARNING: The manufacturers and distributors of the SpeedVault Biometric safe do not
recommend, suggest, advise, promote or otherwise condone the ownership or use
of firearms. We at GunVault Inc. believe the decision to own or use a firearm is a
serious decision that should only be made by an adult who has carefully considered
the risks and benefits of such a decision.
WARNING: The keypad and push buttons on the control panel are electronic. They
have a certain feel to them and may seem different to different people. It is
important for you to become accustomed through practice, as to how the
SpeedVault Biometric safe responds to your own personal touch.
WARNING: Never mix alcohol or drugs with firearms or the SpeedVault Biometric safe.
Alcohol and other substances likely to impair normal mental or physical functions
should not be used before shooting or handling firearms or the SpeedVault
Biometric safe.
WARNING: Never grab your firearm by the trigger when removing or placing into the
SpeedVault Biometric safe. Make sure your firearm’s safety mechanism is on.
WARNING: Always point your firearm in a safe direction. Common sense should
dictate which direction is the safest.
WARNING: Always follow the firearm safety rules set out by the firearm’s manufacturer.
WARNING: Be familiar with how firearms work. GunVault recommends that you obtain
as much information as possible on firearm safety.
WARNING: Always handle firearms as if they are loaded and ready to fire. Always
assume that a firearm is loaded.
WARNING: In order to enjoy the maximum security benefits of the SpeedVault
Biometric safe product, it must be mounted in place using the equipment provided
with the product, according to the instructions provided herein. Use of this product
as a storage receptacle without mounting according to the instructions provided
herein, may compromise security of the SpeedVault Biometric Safe.

- 2 -
Understanding Biometrics
Biometrics are methods of authenticating the identity of person based on
physiological or behavioral characteristics. Biometric fingerprint authentication
refers to technology that measure and analyzes human physical characteristics
for identification and authentication purposes.
Everyone is known to have their own unique individual fingerprints. The
individuality of each fingerprint can be determined by the pattern of ridges and
furrows on the surface of the finger as well as by the minutiae points. Minutiae
points are local ridge characteristics that occur at either a ridge bifurcation or a
ridge ending.
The biometric scanner is a sensitive device that requires care not to damage the
device. In addition, it is recommended that you practice the authentication
process several time in order to become comfortable with the process.
About SpeedVault Biometric
SpeedVault Biometric is the ultimate solution to complete access control.
Invented and developed by GunVault, SpeedVault Biometric provides safe
storage and easily controlled access for handguns, weapons, ammunition,
jewelry and other valuable items including: pharmaceuticals, coins, stamps,
stocks, bonds, critical data and personal documents. SpeedVault Biometric
requires no external computer or power to function. Flash memory retains
fingerprint data even during complete battery or electrical failure.
Shipped with your SpeedVault Biometric are the following items:
SpeedVault Biometric
Mounting Bracket
Two backup keys
Instruction Manual

- 3 -
GETTING STARTED
NOTE: Set your keys to the side. Don’t lock them inside the safe!
Make sure to remove the backup key from the SpeedVault Biometric before
use and secure them.
The key is for emergency use only to unlock the case in the event of
fingerprint failure.
If the key is used to access the SpeedVault Biometric; it can only be removed
from the lock cylinder by returning the key back to its original locked position.
Please do not try to remove the key in any other position or this may cause
damage.
Do not try to use the fingerprint scanner and electronic locking system while
the key is in the unit.
ENROLLMENT OF THE ADMINISTRATOR
FINGERPRINTS
NOTE: The unit can store 120 fingerprints with the first two enrolled fingerprints
assigned as administrators. If the Learn Button is pressed and the LED flashes
red once and the unit beeps once the unit has reached its120 fingerprints
maximum.
NOTE: The unit requires the first or the second administrator’s fingerprint to be
enrolled before adding additional fingerprints.

- 4 -
Register the first two fingerprints as the administrator.
Press the Learn Button. You will hear one beep and the LED will flash green
indicating the enrollment procedure has started.
Place your finger over the scanner with the tip of your finger at the top of the
finger guide as shown in Figure B.
Make sure you have good, flat contact with the scanner. Begin to swipe your
finger from Position 1 to Position 2 (Figure C), taking 1 to 2 seconds to
complete the swipe. Try to get your entire fingerprint to cross the scanner.
Once the swipe is completed you will hear a beep. Repeat Step 3 one more
time. After swiping your finger 2 times the unit will beep twice, this indicates a
successful enrollment. If the swipe fails, the LED will flash red and the unit will
wait for another swipe.
Repeat steps 1 through 5 to add the second administrator.
ENROLLING ADDITIONAL USERS
Press the Learn Button. You will hear one beep and the LED will turn green
indicating the enrollment procedure has started.
Swipe the administrator fingerprint from Position 1 to Position 2 (Figure C)
and you will hear two beeps indicating the additional fingerprint is ready for
enrollment.
Place the new finger to enroll over the scanner with the tip of your finger at the
top of the finger guide as shown in Figure B.
Make sure you have good, flat contact with the scanner. Begin to swipe the
new finger from Position 1 to Position 2 (Figure C), taking 1 to 2 seconds to
complete the swipe. Try to get your entire fingerprint to cross the scanner.
Once the swipe is completed you will hear a beep. Repeat Step 3 one more
time. After swiping your finger two times the unit will beep twice, this indicates
a successful enrollment. If the swipe fails, the LED will flash red and the unit
will wait for another swipe.

- 5 -
ACCESSING THE UNIT
NOTE: The SpeedVault Biometric can be accessed either by valid fingerprint or
via the keys provided.
Fingerprint Access
Press and release the Start Button, the green LED flashes two times and the
unit beeps once.
Place your finger over the scanner with the tip of your finger at the top of the
finger guide as shown in Figure B.
Make sure you have good, flat contact with the scanner. Begin to swipe your
finger from Position 1 to Position 2 (Figure C), it will take 1 to 2 seconds to
complete the swipe. Try to get your entire fingerprint to cross the scanner.
If the unit detects a match, the LED will flash green two times and you will
hear two beeps, then the unit is open.
If the unit doesn’t detect a match, the LED will flash green and red, you will be
denied access. If an enrolled user is denied access, please try again. If the
problem persists, please delete all users and re-enroll again.
Key Access
NOTE: Key Access is intended for backup use only.
Insert the key into the front of the unit.
Turn clockwise to unlock the unit.
Lift the top of the SpeedVault Biometric to open.
To remove the key, close the SpeedVault Biometric, turn the key
counterclockwise.
DELETING USERS/RESETTING THE UNIT
NOTE: Individual users cannot be deleted from the SpeedVault Biometric. All
users will be deleted together.
To delete all fingerprints currently stored on the SpeedVault Biometric, press
and hold the Delete Button, the LED will turn red, and then press the Start
Button.

- 6 -
The unit will beep twice and the LED will flash green twice, indicating all users
fingerprints are deleted. If no fingerprints are stored, the red led will flash once
and beep once.
Replacing the Battery
NOTE: Low Battery Warning - When the unit is powered on, if the LED flashes
red and the unit beeps 3 times, this indicates a low battery.
Pull open the battery cover and remove the old battery.
Insert new 9v battery, following the Positive (+) and Negative (-) guides on the
holder.
Reinsert the battery and snap the battery cover back into place.

- 7 -
Mounting Bracket Installation
Tools Required: Mounting Bracket Images:
Phillips-Head Screw Driver
Optional Tools:
Power Drill
Phillips-Head Bit
Supplied Parts:
SpeedVault Biometric Safe x 1
Mounting Bracket x 1
Wood Screws x 4*
Thumbscrew(s) x 5
* Mounting screws provided are
for solid wood surface only. If mounting to another surface type, drywall,
cement, and etc, the appropriate hardware can be purchased through a local
hardware store.
Mounting Positions:
The SpeedVault Biometric can be mounted from the left, right, or back using the
provided bracket holes (see images below).
Left or Right Side View:
Back Side View:

- 8 -
Installing the SpeedVault:
IMPORTANT: When mounting the SpeedVault Biometric make sure the drawer
has enough space to drop open. The drawer requires gravity to fully release,
always install in a vertical position (see image below)
1. Secure the “Mounting Bracket” to the desired location using the “Wall
Mounting Holes” on the bracket and the provided wood screws.
IMPORTANT: Mounting screws provided are for solid wood surface only. If
mounting to another surface type, drywall, cement, and etc, the appropriate
hardware can purchased through a local hardware store.
2. Remove the two “Thumbscrews” located on the bottom of the SpeedVault
Biometric (see image below).
3. After removing the two “Thumbscrews”, open the SpeedVault Biometric
using the supplied keys. This will allow the drawer to be removed by lifting it
up and out.
4. With the drawer removed, the SpeedVault Biometric can now be mounted to
the bracket. Insert the “Mounting Hooks” into the “Hook Mounting Holes”
located on the left, right, or back of the SpeedVault. Now that the SpeedVault
Biometric is mounted to the bracket, it can be secured to the bracket by using
the supplied “Thumbscrews”.

- 9 -
5. Locate the three “Thumb Mounting Holes” beneath the “Mounting Hooks”
inside the safe. They will be on the same side as the “Mounting Bracket”.
6. Insert the “Thumbscrew” into the “Thumb Mounting Hole” and turn
clockwise until tight. Repeat for the other two “Thumbscrews”. The
SpeedVault Biometric is now securely mounted.
7. Reinstall the drawer and the two “Thumbscrews”.
8. The SpeedVault Biometric is now ready to be used.

- 10 -
Technical Support
If you have followed the above steps carefully and still have a problem operating your
SpeedVault Biometric, phone GunVault Technical Support. Almost all problems can be
solved within minutes over the telephone.
800-222-1055
Requirements for Return & Repair
If possible, do not return your SpeedVault Biometric safe to your dealer. Instead, call
GunVault Technical Support Department. GunVault product delivered without a
pre-arranged Return Authorization Number may be returned unopened, at owner
expense, and fees may accrue.

- 11 -

- 12 -
Limited Warranty
1. GunVault (the “Company”) warrants to the original consumer (the “Purchaser’)
that the SpeedVault Biometric safe will be free from defects in workmanship and
materials for a period of one (1) year from the date of purchase. These
warranties are not assignable or transferable to any other person.
2. Any damage to the SpeedVault Biometric safe as a result of misuse, tampering,
abuse, neglect, accident, improper installation, modification, unauthorized
service, destruction, or the alteration of the serial number, or use violation of the
instructions furnished by the Company will void this warranty.
3. The sole responsibility of the Company shall be limited to the repair or
replacement (in its sole discretion) of any component of SpeedVault Biometric
safe which fails to conform to this warranty at no cost to the purchaser for a
period of one (1) year from the date of original purchase.
4. Contact the Company directly to obtain service under this warranty. If it becomes
necessary to send a defective product to the Company, a Return Authorization
Number must first be obtained from the company.
5. Products shipped without prior Return Authorization and Return Authorization
Number may not be accepted, and the Company will not be responsible for their
disposition and/or cost of return to the owner.
6. The Company will not assume any responsibility for any loss or damage incurred
in shipping. All return authorized products should include a copy of the original
invoice in order that this warranty may be honored.
7. This warranty is not an insurance policy. The Company is not responsible for
damage to or theft of the Purchaser’s SpeedVault Biometric safe or its contents.
8. We recommend that the enclosed warranty card be completed in full, and
returned to the Company within ten (10) days of the original date of purchase to
validate this warranty.
9. Any implied warranties which the purchaser may have are limited to the duration
of the warranties described above. There are no further warranties which extend
or apply beyond the face hereof, and the company expressly disclaims and
excludes any and all warranties of merchant ability or fitness for a particular
purpose. Some states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.
10.Repair or replacement shall be the sole remedy for the purchaser under this
warranty. The Company shall not be liable for any direct, indirect, incidental or
consequential damages, losses or expense arising from the use or misuse of the
SpeedVault Biometric safe. Some states do not allow the exclusion or limitations
of incidental or consequential damages, so the limitation may not apply to you.
11.This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.

- 13 -
Notes

- 14 -

- 15 -
Inquiries or questions regarding the SpeedVault Biometric should be directed to:
GunVault, Inc.
Technical Support 800-222-1055
Protected by United States Patent Numbers
5,161,396 and 5,549,337