GVI Security GV-BVF480 User manual

Operating Instructions
GV-BVF480
1/3” Color, Varifocal, Weather Resistant,
Bullet Camera
Before installing and using the camera, please read the
instructions thoroughly and retain them for reference.
2
This symbol is intended to
alert the user to the presence
of non insulated “dan erous
volta e” within the product’s
enclosure that may be of
sufficient ma nitude to
constitute a risk of electric
shock to persons.
The exclamation point within
an equilateral trian le is
intended to alert the user to
the presence of important
operatin and maintenance
(servicin ) instructions in the
literature accompanyin the
product.
Warning
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicin to qualified
personnel only.
Wirin methods shall be in accordance
with the National Electric Code,
ANSI/NFPA 70.
egulatory Notices For U.S.A
This equipment has been tested and found
to comply with the limits for a Class A di ital
device, pursuant to Part 15 of the FCC
Rules. These limits are desi ned to provide
reasonable protection a ainst harmful
interference in a residential installation! This
equipment enerates, uses and can radiate
radio frequency ener y and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications.
However, there is no uarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turnin the equipment off and on, the user is
encoura ed to try to correct the interference
by one or more of the followin measures:
•
••
• Reorient or relocate the receivin
antenna.
•
••
• Increase the separation between the
equipment and receiver.
•
••
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
•
••
• Consult the dealer or an experienced
radio/TV technician for help.
This Class A di ital apparatus meets all
requirements of the Canadian Interference -
Causin Equipment Re ulations.
This product is manufactured to comply with the radio interference requirements of
EMC Directive 89/336/EEC and 93/68/EEC.

3
Contents
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features and Name of Each Part . . . . . . . . . . . . . . . . . . . . . . . 6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Notes on installation and usa e . . . .. . . .. .... 7
• Camera installation . . . . . . . . . . . . . . . . . . . . 7
Troubleshootin . . . . . . . . . . . . . . . . . . . . . . . . . .8
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Other Information . . . . . . . . . . . . . . . . . . . . . . . . 11
4
Precautions
Do not attempt to disassemble
the camera
To prevent electric shock, do not remove
screws or covers. There are no user
serviceable parts inside. Ask a qualified
service personnel for servicin
.
Avoid
facing the came
ra with
direct sunlight
Do not aim the camera at bri ht objects.
Never face it with direct sunli ht or other
extremely bri ht objects. Otherwise
bloomin or smear may be caused.
Do not use strong solvents or
detergents
Use a dry cloth to the camera when it is dirty.
If it is hard to remove the dirt on the camera,
use a mild deter ent and wipe it ently.
Before operating, please check
proper temperature, humidity
and power source ratings.
Use the camera under conditions where
temperature is between 14°F~122°F
(-10°C~50°C)
Do not expose the camera in
such conditions shown below.
Do not use in a room or area filled with
ci arette smoke, dust or as.
Handle the camera with care
Do not abuse the camera. Avoid strikin ,
shakin , etc. The camera could be
dama ed by improper handlin or
stora e.

5
Composition
Confirm that the followin parts are included:
Camera Sun Shield Bracket
Sun-Shield Bolt Screw
Instruction Manual
6
FEATU ES
• Bullet color camera
• 1/3” Super HAD Sony CCD
• 480 TV Lines Resolution
• Minimum Scene Illumination 0.3 Lux
• Varifocal Fixed Iris Lens built-in 4~9mm Vari-
focal, Fixed Iris F1.5 Lens
• Externally Adjustable Focal Len th & Focus by Rin
• Back Li ht Compensation
• Weather Resistant (IP66)
• Back, Top and Bottom Side Bracket Mountin available
• 12VDC
 Name of Each Part
POWER(DC12V)
VIDEO-OUT
ZOOM RING
FOCUS RING
BRACKET HOLE
(DON'T UNSCREW)
SUN SHIELD SUN SHIELD BOLT
BRACKET HOLE
BLACK(-)
RED(+)

7
Installation
 Notes on installation and usage
1. Do not disassemble the camera.
2. Always handle the camera with care. Please avoid mechanical shock or
vibration, and take caution to prevent dama es or make scratches on the
camera window lass due to careless stora e and/or handlin .
3. Do not clean the camera body with stron abrasives or soaps. When the
camera becomes dirty, clean it with dry ru s. Take Precaution to use
dedicated ru s to clean window lass
4. Please keep the camera in a cool area that is not exposed to the direct
sunli ht. Failin to do so can cause undesired effects on the product.
 Camera Installation
1. Attach the bracket to the mountin surface by drillin with the supplied screws.
2. For the ideal type of mountin style, refer to the pictures below.
3. For a wide an le view turn the Zoom Rin to wide(W), for a narrower an le
view turn it to tele(T).
4. After adjustin the camera to the desired an le of view, adjust the Focus Rin
to near(N) or far (∞) while holdin the zoom rin by a hand
5. After adjustin the an le of view, cover the camera with the sun-shield and
fix it to the camera with the sun-shield bolt.
[Back Side Mounting] [Bottom Side Mounting]
[Top Side Mounting]
8
Troubleshootin
If you have trouble operating the camera, check the following
guides for the possible cause of the problem.
• Nothin appears on the screen.
->Check the power and video si nal line connection.
• The video ima e is not clear.
-> Check if the window lass has dust on the surface.
Clean the window lass with a clean cloth or brush.
-> Make sure that the screen is not exposed directly to a bri ht li ht.
Adjust the position of the camera if necessary.
-> Check if protective sheet of camera window is removed.
• The screen is dark.
-> Adjust the contrast feature of the monitor.
If you can’t solve the problems with above guidelines, please contact
an authorized technician.

9
Specifications
Model GV-BVF480
Si nal System NTSC
Ima e Sensor 1/3” Super HAD Sony CCD
Effective Pixels 768H×494V (380K pixels)
Scannin System 525 Lines 2:1 Interlace
Scannin Frequency 15.734KHz (H), 59.94Hz (V)
Resolution 480TV-Lines
Shutter Speed 1/60 ~ 1/100,000sec.
S/N Ratio More than 48dB (AGC off)
Sync. System Internal
Min. Illumination 0.3 Lux
White Balance AWC
Video Output VBS 1.0 Vp-p (75 Ω load)
Lens 4~9mm Vari-focal, Fixed Iris F1.5 Lens
Power Supply DC12V±10%
Power Consumption Max.160mA (DC12V)
Operatin Temp. 14°F~122°F (-10°C~50°C)
Operational Humidity 90% RH max.
Dimension 44mm ( Ø ) x 116mm (L)
* Desi n and specifications are subject to chan e without notice.
10
 Dimension
Unit: mm (inch)
Ø44.0(1.73)
52.8(2.08)

11
 Other Information
Material Information
- Body and Bracket: Aluminum
- Glass Thickness: 1.85mm
12
GVI Security,
Inc.
• 2801 Trade Center Dr., Suite 120
• Carrolton, TX 75007
• Toll Free: 888-595-2288
• Fax: [phone]
•
www. viss.com
MADE IN KO EA