Gyyr TLC2100SHD User manual

TLC2100SHD
RS-232 Optional Feature
Operating Instructions

TLC2100SHD
RS-232 Optional Feature
Operating Instructions

Copyrights
© 2003 Silent Witness Enterprises Ltd.
This document is copyrighted with all domestic and international rights reserved. No part
of this document may be reproduced, stored in a retrieval system, or transmitted, in any
form, by any means, without the prior written permission of Silent Witness Enterprises
Ltd.
Trademarks
SilentWitness®is a registered trademark of Silent Witness Enterprises Ltd.
All brand names and product names are trademarks or registered trademarks of their
respective companies and are used with the permission of their owners.
Revisions
This document is written and published by Silent Witness Technical Communications in
Surrey, B.C., Canada. Every precaution has been taken to ensure its accuracy, but if you
do find an error, please contact us.
Silent Witness Enterprises Ltd. assumes no responsibility for errors in this document,
omissions, or their consequences. The information is subject to change without notice.
Reordering
When requesting additional copies of this document, please include the following
information:
Address all comments and requests regarding this document to:
Technical Communications
Silent Witness Enterprises Ltd.
6554 - 176th Street
Surrey, B.C. V3S 4G5
Canada
Tel:[phone]
Fax:[phone]
Toll free:1.888.289.2288
International: Toll free00.800.2020.8080 or +1.604.574.1523
Website:http://www.silentwitness.com
Part Number: 900.0060
Revision 1.01
Date of Issue: June 10, 2003

Document 900.0060 Rev 1.01 v
STOP!
TO SET SECURITY LOCK (Locks out access to VCR functions)
1. Press the NEXT and UP buttons at the same time.
2. Check the digital display. The Lock Annunciator will light when the lock is activated. Lwill appear below the
Alarm Counter of the TIME/DATE stamp on the monitor.
3. To deactivate security lock, press the NEXT and UP buttons at the same time. The Lock annunciator will no
longer be lit in the display. Lwill disappear from the TIME/DATE stamp on the monitor.
12-07-03 PL SUN A04
08:28:44A 30 T L
THE VERY FIRST TIME YOU POWER-UP YOUR VCR, PERFORM A MASTER RESET
TO PERFORM A MASTER RESET
The MASTER RESET function is performed by inserting a pointed object into each of the Reset holes at the same
time. This is used to perform a MASTER RESET for abnormal Time Lapse system operations such as T/D DISPLAY,
Speed Select, and so on. All programmable features must be reprogrammed after reset. A MASTER RESET tool is
supplied with this unit.
This unit is also equipped with a SYSTEM RESET function. The SYSTEM RESET function will NOT change any of the
menu settings. See "Tape Adjustment Controls: System Reset" for further information. Note: A SYSTEM RESET may
also be performed for Mecha Lock, Cyl Lock & Reel Lock. For more information, contact factory.
SHARPNESS 2-A24HR
TRACKING
SLOW
TRACKING
VLOCK PREV. DOWN V-POS H-POS ALARM
INDEX
ALARM
RESET
COUNTER
RESET
REC / PLAY
HOURS
TIMER DAYLIGHT
SAVINGS
S
PROG. NEXT UP
EJECT
REC
FIELD
REV
STILL FIELD
FWD
REVERSE
PLAY
REW/
SEARCH
F. F W D /
SEARCH
STOP PLAY
ABC
Next and Up
buttons
TAB TAPE END
INDEX
ALARM
TIMER BR
SPEED
LOCK
REC
Lock Annunciator
SHARPNESS 2-A24HR
TRACKING
SLOW
TRACKING
VLOCK PREV. DOWN V-POS H-POS ALARM
INDEX
ALARM
RESET
COUNTER
RESET
REC / PLAY
HOURS
TIMER DAYLIGHT
SAVINGS
S
PROG. NEXT UP
EJECT
REC
FIELD
REV
STILL FIELD
FWD
REVERSE
PLAY
REW/
SEARCH
F. F W D /
SEARCH
STOP PLAY
ABC
Reset
holes
REMOVE THIS CARD AND KEEP IN A SECURE PLACE. THIS
RECORDER HAS A CONCEALED SECURITY LOCK TO
RESTRICT UNAUTHORIZED USAGE OF THIS RECORDER
Lock indicator in
Time/Date stamp
End User Card
Dealer Card

June 10, 2003
vi

TLC2100SHD Operating Instructions
Document 900.0060 Rev 1.01 vii
Contents
About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Overview of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi
Cautions and Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii
1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Typical Installation Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2 Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Tape and Picture Adjustment Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Play/Record Operation Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Programming Operation Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Position and Alarm Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Timer and Miscellaneous Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Digital Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Rear Panel Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Video Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Audio Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Record Check Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Alarm Index Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3 Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
To Move and Edit in the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Time/Date Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Example of Setting the Clock and Navigating a Menu . . . . . . . . . . . . . . . . . . . . 24
Display Options Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
System Code Field. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Text Positions Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
System Options Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Timer Program Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Alarms Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Alarm Memory Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Alarm Record Options Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Camera Switcher Pulse Submenu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

June 10, 2003
Contents
viii
STD/Remote Port Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Remote Terminal Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Set 1 - Operational Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Set 2 - VCR Status Return Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Set 3 - VCR Extended Status Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Set 4 - Program Control Function Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Set 5 - Tape Speed Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Set 6 - Extended Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Set Date Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Read Date Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Set Time Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Read Time Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Set System Code Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Read System Code Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Set Timer Program Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
System Data Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Appendix A External Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Appendix B Remote Control Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Appendix C Warning Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Digital Display Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Appendix D Periodic Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Periodic Maintenance Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Regular System Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Appendix E Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Appendix F Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

TLC2100SHD Operating Instructions
Document 900.0060 Rev 1.01 ix
Figures
Figure 1-1 Typical Security Installation With ATM or ECR . . . . . . . . . . . . . . . . . . . . . . .3
Figure 1-2 Typical Security System With a Camera Multiplexer . . . . . . . . . . . . . . . . . . . . .4
Figure 2-1 Front Panel with Control Compartment Open . . . . . . . . . . . . . . . . . . . . . . .5
Figure 2-2 Front Panel with Control Compartment Closed . . . . . . . . . . . . . . . . . . . . . . .5
Figure 2-3 Cassette Compartment and Eject Button . . . . . . . . . . . . . . . . . . . . . . . . . .6
Figure 2-4 Tape and Picture Adjustment Controls . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Figure 2-5 Play/Record Operation Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Figure 2-6 Play/Stop Operation Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Figure 2-7 Programming Operation Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Figure 2-8 Position and Alarm Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Figure 2-9 Timer and Miscellaneous Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 2-10 Digital Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 2-11 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 2-12 Video and 15-Pin Connector Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 2-13 Audio Connector Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 2-14 Digital Display and Alarm Index Button . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 3-1 Full Time/Date Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 3-2 Half Time/Date Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

TLC2100SHD Operating Instructions
Document 900.0060 Rev 1.01 xi
About This Document
This document describes the TLC2100SHD timelapse recorder and provides the
procedures for installing the timelapse recorder system. This document also describes
the menus you use to configure and operate the timelapse recorder.
Overview of Contents
This document contains the following chapters and appendixes:
•Chapter 1, Getting Started, introduces the TLC2100SHD timelapse recorder, gives a
functional overview of its components, and explains what you need to get started.
•Chapter 2, Controls, lists the different controls available with the TLC2100SHD and
their functions. This chapter also explains how to use those controls to perform
tasks such as installation and record checks.
•Chapter 3, Menus, describes the Main Menu and submenus involved in using the
TLC2100SHD.
•Appendix A, External Interface, presents a detailed description of the 15-pin D
connector and the functions of each pin.
•Appendix B, Remote Control Feature, explains how to use the TLC2100SHD remote
control feature.
•Appendix C, Warning Codes, describes warning codes that may appear and what they
mean.
•Appendix D, Periodic Maintenance, lists suggested periodic maintenance steps to
ensure maximum performance of the TLC2100SHD.
•Appendix E, Troubleshooting, lists common operational problems that may be
encountered from time to time and provides possible solutions.
•Appendix F, Specifications, lists the TLC2100SHD specifications.

June 10, 2003
xii
Cautions and Warnings
WARNING! To prevent fire or electrical shock, do not expose this
appliance to rain or moisture.
Caution To prevent electric shock do not remove cover. No user
serviceable components inside. Refer servicing to qualified service
personnel.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
The lightning flash with the arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.

TLC2100SHD Operating Instructions
Document 900.0060 Rev 1.01 xiii
Note This equipment has been tested and found to comply with part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction guide, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
Note This digital apparatus complies with Canadian ICES-003.
Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacture of
your video product, safety is a major factor in the design of every instrument. Safety is
also your responsibility.
The following sections list important information that will help to assure proper use of
a video cassette recorder and accessory equipment. Please read it carefully before
operating your video product and keep it in a handy place for future reference.
Use High Quality High Grade VHS Cassettes
High resolution timelapse recording requires a high quality high grade tape for
satisfactory performance. Some brands of tape can have an adverse effect on video head
performance and head life. The following brands have been found to meet our critical
specifications:
GYYR BASF MAXELL TDK
Read Instructions
Read all of the safety and operating instructions before the appliance is operated.

June 10, 2003
xiv
Retain Instructions
Retain the safety and operating instructions for future reference.
Heed Warnings
Adhere to all the warnings on the appliance and in the operating instructions.
Follow Instructions
Adhere to all of the “operating and use” instructions.
Grounding
This video product is equipped with a 3-wire grounding-type plug (a plug having a third
pin for grounding). This plug will only fit into a grounding-type power outlet. This is a
safety feature. If you are unable to insert the plug into your outlet, contact your
electrician to replace your obsolete outlet. Do not attempt to defeat the safety purpose
of the grounding-type plug.
Power Sources
This video product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power you are using, consult your
video dealer or local power company.
Overloading
Do not overload wall units and extension cords as this can result in a risk of fire or
electric shock. Frayed power cords, damaged or cracked wire insulation, and broken
plugs are dangerous. Periodically examine the cord and have it replaced by your service
technician if appearance indicates damage or deteriorated insulation.
Power-Plug Protection
The power supply cords should be routed so they are not likely to be walked on or
pinched by items placed upon or against them. Pay particular attention to cords at the
plug, convenience receptacles, and the point where the cord exits from the video
product.

TLC2100SHD Operating Instructions
Document 900.0060 Rev 1.01 xv
Ventilation
Slots and an opening in the cabinet are provided for ventilation and to ensure reliable
operation of the video product and to protect it from overheating. Therefore, these
openings must not be blocked or covered. The openings should never be blocked by
placing the video product on a bed, soft rug, or other similar surface. This video product
should not be placed in a built-in installation such as bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been followed.
Attachments
Do not use attachments other than those specifically recommended by the video
product manufacturer as they may cause hazards.
Caution Maintain electrical safety. Powerline operated equipment or
accessories connected to this unit should bear the UL listing mark
or CSA certification mark on the accessory itself and should not
have been modified so as to defeat the safety features. This will
help avoid any potential hazard from electric shock or fire. If in
doubt, contact qualified service personnel.
To Prevent Shock Hazard, Do not Expose this Unit to Rain or
Moisture
If you spill liquid on the unit, consult authorized service personnel. Moisture can damage
internal parts. Do not use this recorder near sources of water.
Accessories
Do not place this video product on anything unstable: cart, stand, tripod, bracket, or
table. The video product may fall, causing serious injury to a child or adult, and serious
damage to the appliance. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer. Any mounting of the video product should follow
the manufacturer’s instructions, and should use a mounting accessory recommended by
the manufacturer.
An appliance and cart combination should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance and cart combination to overturn.

June 10, 2003
xvi
Cleaning the Outside Surfaces
Unplug this video product from the wall outlet before cleaning. Do not use liquid aerosol
cleaners. Use a damp cloth for cleaning.
Object and Liquid Entry
Never push objects of any kind into this video product through openings as they may
touch dangerous voltage points or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the video product.
Servicing
Do not attempt to service this video product yourself. Opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Conditions Requiring Service
Unplug this video product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
• When the power cord or plug is damaged
• If liquid has been spilled into the video product
• If the video product has been exposed to rain or water
• If the video product does not operate normally by following the instructions.
Adjust only those controls that are covered by the operating instructions. The
adjustment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the video product to its normal
operation.
• If the video product has been dropped or the cabinet has been damaged
• When the video product exhibits a distinct change in performance—this indicates
a need for service
Replacement Parts
When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric shock, or other
hazards and void the warranty.

TLC2100SHD Operating Instructions
Document 900.0060 Rev 1.01 xvii
Safety Check
Upon completion of any service or repairs to this video product, ask the service
technician to perform safety checks to determine that the video product is in safe
operating condition.
Important Note to the Installer
This installation should be made by qualified service personnel and should conform to
all local codes.
In order to provide this product with protection against risk of unintentional operation
by employees, customers, janitors, and cleaners working on the premises, and from
falling objects, building vibrations and similar causes, Silent Witness recommends that:
• This product be enclosed in a tamper-resistant lockbox. Make sure that the
lockbox is well ventilated or maintained with an air cooling system.
• Security locking procedures described on the detachable card at the front of this
guide be followed (page v).

TLC2100SHD Operating Instructions
Document 900.0060 Rev 1.01 1
1
Getting Started
Introduction
If you have never used a timelapse recorder system before, this section explains what
you need to do to get started.
In addition to your timelapse recorder, you need the following equipment:
• A video camera
• A monitor
• Cables for the camera and monitor (typically these are coax cables with BNC
connectors)
• A T-120 or T-130 VHS video tape. Silent Witness recommends the following
brands of tape: Gyyr, BASF, Maxell, and TDK
• Power sources for the VCR, camera, and monitor
Before connecting any piece of equipment to a power source, make the following
connections:
• Connect the camera to the VCRs Video In connector
• Connect the monitor to the VCRs Video Out connector
• Plug in all of your equipment to their power sources. This VCR unit connects into
a 120 VAC wall outlet.
• The very first time you power up your VCR, perform a Master Reset. The
procedure for performing a Master Reset is on the detachable STOP! page at the
beginning of this guide (page v).
• Insert the video tape into the unit
Your monitor should now display a camera image. A Time/Date stamp displays on the
monitor with its factory default setting. A flashing message displays: Set Clock.
If you wish to program the Time/Date Display, see Time/Date Submenu on page 24. A
step-by-step description is covered in that section.

June 10, 2003
Getting Started
2
You will also notice that the letters PL are flashing in the Time/Date display. PL stands
for Power Loss. To remove PL from the display, simply press the ALARM RESET
button. However, be aware as you learn about the more advanced functions of your
VCR, that pressing the ALARM RESET button will also clear the alarm memory.
If you wish to display the VCR On-Screen Menus, press the PROG. button. Information
about all the Programming Buttons is found in Programming Operation Controls on page 9.
Information about the VCR On-Screen Menus is found in Menus on page 21.
If you wish to learn more about the Front Panel Controls, you might begin with the
Play/Record Operation Controls. Information about these controls is found in
Play/Record Operation Controls on page 7. These controls are somewhat similar in
operation to those of a home VCR.
As you are operating your recorder, keep an eye on the Digital Display and become
familiar with the various indicators. This display will become invaluable as you become
more comfortable with the operation of your recorder.
If you have questions about the operation of this unit, contact your local dealer or call
one of the phone numbers listed on the back cover for expert assistance.
Typical Installation Scenarios
The diagrams on these two pages depict typical installations at a security system site.
For detailed installation and rear panel interface information, see Rear Panel Functions,
page 14, Video Installation, page 16, and Audio Installation on page 17.

TLC2100SHD Operating Instructions
Document 900.0060 Rev 1.01 3
Figure 1-1 Typical Security Installation With ATM or ECR
IN
OUT
Y/C VIDEO
IN VIDEO OUT
IN OUT
AUDIO
Video Camera
Monitor
RS-232
Text Inserter
Electronic
Cash
Register
Automated
Teller
Machine
EZ Bank ATM
Video In
Alarm
Port
OR
Video Out
POWER
PRGM PREV NEXT DOWN UP

June 10, 2003
Getting Started
4
Figure 1-2 Typical Security System With a Camera Multiplexer
Monitor
Camera Multiplexer
ATM
RS-232 Text Inserter
Video Out
Video Cameras
1 2 3 4 5 6 7 8
FREEZE
DISPLAY
SELECT
TIME
LAPSE
MENU
PREVIOUS
VIEW
NEXT
ENLARGE
RECORD PLAY
DIGISCAN III
Õ
Õ
Õ
Õ
16151413121110
9
POWER
PRGM PREV NEXT DOWN UP
EZ Bank ATM
IN VIDEO OUT
IN OUT
AUDIO
Video In
Alarm
Port